BAFANG H500F User manual

1

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6.1 Introduction 

6.2 Specifications 3

6.2.1 Outline and geometric size 3

6.2.2 Surface 3

6.2.3 Storage Information 3

6.3 Drive Unit Installation 4

6.3.1 List of Tools to be used 4

6.3.2 Motor Installation 4

6.4 Maintenance 5

CONTENT

6 DEALER MANUAL FOR H500F

(RM G060.350.DC)

2BF-DM-C-RM G060-DC-EN November 2019

6.1 INTRODUCTION

•Product Model

RM G060.350.DC

•Scope

Applies only to electrically powered pedelecs

developed or licensed by Bafang. It is suitable

for fat bikes or all terrain bikes, which have been

developed for off road on gravel or sand use.

The engine is not suitable for sport competi-

tions.

•Identiﬁcation

The following graphic, is the identification

numbers of the product, which are shown on

the housing:

Note: Content in the label is important informa-

tion about this product. Please do not remove

the information from the motor.

3

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6.2 SPECIFICATIONS

Motor model: RM G060.350.DC

Rated power (W) 350

Rated voltage (V) 36

Waterproof IP65

Certiﬁcation CE - EMC

Outdoor Temperatures -20℃~45℃

6.2.1 Outline and geometric size

OLD: 175mm

Shaft length: 235mm

Motor cable length: L=250mm

6.2.2 Surface

Shockproof black coating

6.2.3 Storage Information

The pedelec should be stored in a ventilated dry room. Avoid storing the pedelec near strong magnetic

objects.

4BF-DM-C-RM G060-DC-EN November 2019

6.3 DRIVE UNIT INSTALLATION

6.3.1 List of Tools to be used

Use of the Tools Tools

To tighten/loosen the M5*8 screws onto the disc brake. Internal hex wrench

To tighten/loosen the M12 flange nuts. Open spanner

6.3.2 Motor Installation

1. First mount the cassette on the cassette

seat.

2. Tighten the disk brake with six screws onto

motor.

3. Insert the stop pin into on the shaft.

4. Insert the motor into the frame.

5. Mount the 4mm washer on both sides of

the frame.

5

DEALER MANUAL FOR MOTOR

BF-DM-C-RM G060-DC-EN November 2019

6. Tighten clockwise M12 ﬂange nuts with

open spanner at both sides of the motor.

(torque requirement: 47-60 N.m.)

7. Mount the shaft end sheath on both sides

of the shaft ends.

6.4 MAINTENANCE

• Maintenance must be carried out by autho-

rized personnel with the correct equipment.

• Do not disassemble the motor.

• Do not use thinners or other solvents to

clean the components. Such substances can

damage the surfaces.

• Avoid water submerging, to keep the com-

ponents protected.

• Avoid using high-pressure cleaning jets.

• For prolonged storage, turn off the battery

and avoid storing near heat sources.

6BF-DM-C-RM G060-DC-EN November 2019

This manual suits for next models

1

Table of contents

Other BAFANG Bicycle Accessories manuals

Popular Bicycle Accessories manuals by other brands

Sigma

Sigma BC 16.16 manual

Playcore

Playcore Dero Setbacks installation instructions

VDO Cyclecomputing

VDO Cyclecomputing x3dw instruction manual

Cateye

Cateye RAPID X2 manual

buratti meccanica

buratti meccanica Clorofilla Trail Use and maintenance manual

Shimano

Shimano SG-8R20 Service instructions

BOB

BOB YAK owner's manual

APLIC

APLIC 303303/20190717TW012 user manual

SRAM

SRAM AXS BlipBox user manual

Garmin

Garmin EDGE 500 owner's manual

Shimano

Shimano FD-RX810 Dealer's manual

Cateye

Cateye V2C - Quick start manual

KMART

KMART 43115907 instructions

SIGMA SPORT

SIGMA SPORT Buster 2000 manual

NVO Components

NVO Components STEM manual

DAXYS

DAXYS BP188 user manual

XLC

XLC BV-W17 manual

Deda Elementi

Deda Elementi SUPERBOX user manual