ATEN VS-261 User manual
User Manual
VS-261 / VS-461
Read this guide thoroughly and follow the installation and operation
procedures carefully in order to prevent any damage to the units and/or
any devices that connect to them.
This package contains:
!1 VS-261 or VS-461 DVI Video Switch
!1 IR Remote Control Handset
!1 Power Adapter
!1 User Manual
© Copyright 2005 ATEN®International Co., Ltd.
Manual Part No. PAPE-1256-300G
Printed in Taiwan 08/2005
All brand names and trademarks are the registered property of their respective owners.
2005-08-11
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy,
and if not installed and used in accordance with the
instruction manual, may cause interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
!Reorient or relocate the receiving antenna;
!Increase the separation between the equipment and
receiver;
!Connect the equipment into an outlet on a circuit different
from that which the receiver is connected;
!Consult the dealer or an experienced radio/television
technician for help.
2005-08-11
Overview
The 2 port VS-261 and 4 port VS-461 chart a revolutionary new
direction in multimedia functionality by combining a Digital
Visual Interface (DVI) Video Switch with stereo quality audio. It
is not necessary to have a separate display and set of speakers
for each source. Users can switch among two (VS-261) or four
(VS-461) media sources, and enjoy their output on a single
display and set of speakers.
The VS-261 / VS-461 improves on previous video switch
designs by incorporating DVI connectors. DVI supports both
digital video (flat panel displays, data projectors, plasma
displays, digital TVs and set-top boxes) and analog video
(traditional monitors and TVs).
The VS-261 / VS-461 works on both PC compatible and Mac
systems. Setup is fast and easy - simply plug cables into their
appropriate ports. There is no software to configure, no
installation routines, and no incompatibility problems. Two
convenient methods are available to switch among media input
sources: push button port selection switches located on the
unit’s front panel, and an IR remote control.
- 1 -
2005-08-11
Features
!DVI video switch with stereo audio support
!Output sound and video signals from 2 (VS-261) or 4
(VS-461) DVI or analog video sources
!Compliant with the DVI specification
!Video source selection via front panel switches or IR remote
control
!LED display for easy status monitoring
!Superior video quality - 1600x1200 60Hz; DDC2B
!Easy installation
!Supports Windows and Mac host systems
- 2 -
2005-08-11
Hardware Requirements
Output
!A DVI display capable of the highest resolution that you will
be using on any DVI input
!Stereo speakers for audio output
Input
The following equipment must be installed on any computer
that acts as a source of DVI content:
!A DVI port
Note: The quality of the display is affected by the quality of
the DVI display card. For best results, we recommend
you purchase a high quality product.
!An audio output port (optional - for audio accompaniment to
the display)
Cables
Two (VS-261) or four (VS-461) DVI cables are required to
properly operate this DVI Switch (not included).
Note: 1. Cables are not included in this package. Since the
quality of the display is affected by the quality and the
length of the cables, we strongly recommend that you
purchase high quality cables. Contact your dealer to
purchase the correct cable sets for your switch.
2. There are two types of DVI signals (DVI-A and
DVI-D). The cable type must support the signal type
used by the DVI source and the DVI display. We
recommend that you use DVI-I cable, as it supports
both digital and analog signals.
- 3 -
2005-08-11
VS-261 / VS-461 Front View
1. Port
Selection
Switches
Press a switch to display video (playback
audio) from the device attached to the
corresponding port.
2. Port LEDs The Port LEDs are built into the Port
Selection Switches.
- The ON LINE LED lights to indicate that the
device attached to the corresponding port is on.
- The SELECTED LED lights to indicate that
the video (audio) input is from the device
attached to the corresponding port.
3. IR Receiver Receives port switching signals from the
remote handset.
- 4 -
1
23
1
23
2005-08-11
VS-261 / VS-461 Rear View
1. Power Jack The power adapter cable plugs in here.
2. Video/Audio
Output
The output section is comprised of a DVI-I
connector and two RCA audio jacks. The
cables that connect to the video and audio
input ports on the Video Display plug in here.
L=left audio, R=right audio.
3. Video/Audio
Input
Each input section is comprised of a DVI-I
connector and two RCA audio jacks. The
cables that connect to the video and audio
output ports on the source devices plug in
here. Be sure that the cables from an
individual source device all plug into the same
input section (e.g. all in Port 1, etc.).
- 5 -
1 2 3
1 2 3
2005-08-11
IR Remote Control Unit
1. Port Up /
Port Down
Press Port Up to switch the media input
focus from the device on the currently
selected port to the device on the next port (1
to 2, 2 to 3, etc.).
Press Port Down to switch the media input
focus from the device on the currently
selected port to the device on the previous
port (3 to 2, 2 to 1, etc.).
2. Port
Selection
The button numbers correspond to the media
input ports on the rear panel of the VS-261 /
VS-461. Press a button to switch the media
input focus to the device attached to the
button’s corresponding port.
Note: Since the VS-261 only has two input
ports, it only uses buttons 1 and 2. Pressing
button 3 or 4 has no effect.
- 6 -
1
2
2005-08-11
Installation
Important: Ensure that all devices are powered off and
properly grounded before connecting them to
the switch.
Installing your DVI Video Switch involves the following five
steps (please also refer to the installation diagram):
1. Use a DVI-I compatible cable to connect the Video Out port
on the switch to the video input port on the DVI Video
Display.
2. Use stereo audio cables to connect the Audio Out (L + R)
jacks on the switch to the inputs on the audio receiver,
stereo system or speakers.
3. Use a DVI cable to connect the video output port on the
source device to an available DVI port on the Input section of
the switch.
4. Use stereo audio cables to connect the audio output jacks
on the source device to the Audio In jacks on the switch that
correspond to the DVI input from the same source device.
5. Plug the provided power adapter into an AC power source,
then plug the power adapter cable into the DC Power Jack
on the switch.
This completes the installation. You may now turn on the
display and source devices.
- 7 -
2005-08-11
- 8 -
1
2
3
5
4
2005-08-11
Other manuals for VS-261
2
This manual suits for next models
1
Table of contents
Other ATEN Switch manuals
ATEN
ATEN RCM Series User manual
ATEN
ATEN Master View CS-9134 User manual
ATEN
ATEN CN9600 User manual
ATEN
ATEN KN4164Vl User manual
ATEN
ATEN CL5708M Guide
ATEN
ATEN CL6708MW User manual
ATEN
ATEN ATEN VanCryst VM1600A User manual
ATEN
ATEN CS1842 User manual
ATEN
ATEN CS1964 User manual
ATEN
ATEN Bi-Tronics AF-142 User manual
ATEN
ATEN AS-411P User manual
ATEN
ATEN VM0202H User manual
ATEN
ATEN CS-64A User manual
ATEN
ATEN KL1108V User manual
ATEN
ATEN CS-62B User manual
ATEN
ATEN ALTUSEN KL1508 Operator's manual
ATEN
ATEN CL6708MW User manual
ATEN
ATEN Master View Slideaway ACS-1208AL User manual
ATEN
ATEN CS1922ATC User manual
ATEN
ATEN US3344I User manual
