Atek INC 110 Series User manual
KK-INC.002 10.02.21 Rev No:3
1
Signal
M12 Socket
Cable
V+ (12..24VDC)
Pin 1
Red
Output 1 (0.1-10VDC / 4-20mA) (X axis)
Pin 2
Yellow
GND (0V)
Pin 3
Black
Output 2 (0.1-10VDC / 4-20mA) (Y axis)
Pin 4
Green
Reset
Pin 5
Pink
•The installation of the product is carried out by the customer who purchases the product, according to the wiring diagrams,
installation information, etc. in this manual.
•Maintenance and repair should be done by the technicians authorized by the manufacturer firm.
•There must be minimum distance between the sensor and control unit. Avoid additions except the suitable connector unless
it needs.
•Keep away the sensor cable from as high power energy cables, contactor, motor, switched power supplies, inductive and
capacitive noisy supplies.
•Not to damage the sensor, supply directions and voltage must be paid attention. Don’t energize before all connections
completed.
•Transport and storage should be at their original packaging and an ambient temperature of -30°C / +70°C in such a way that
they will not be exposed to dust, humudity, impact, vibration, falling or water.
•Chemicals such as alcohol, thinner etc. should not be used for cleaning the product. The product should be wiped with a
damp cloth.
•The product may be damaged and may become unusable if used outside of the specifications in the user manual.
* Output 2 is only used on two-axis models. On single-axis models, Pin 4 (green cable) is
empty.
* On analog output models, 1 pcs M12 5 pin male socket is used as standard.
* Different socket models can be requested optionally.
INC 110 E (Analog Output)
INC 110 series tilt sensors are used for inclination measurement for single (X) or two axes
(XY). They have ±90⁰ measurement range. These sensors with 0.1-10VDC voltage output or
4-20mA current output option, can take measure ment with ±0.1° accuracy. Thanks to its
compensated axis sensitivity, the effect of the axes on each other is minimized.
These sensors, especially used in machine and crane industries, can operate in outdoor
environments with their high IP protection classes.
sert ortamlarda açıları. Endüstride ve otomotiv mühendisliğinde her türlü uygulamada
kullanıma uygundur.
INCLINOMETER (TILT SENSOR) USER MANUAL
M12 - 5 PIN MALE
SOCKET
M12 - 5 PIN FEMALE
SOCKET
WARNINGS
GENERAL INFORMATIONS
ELECTRICAL CONNECTION
DETERMINING THE 0° POINT OF SENSOR
Pin 5 (pink cable) and pin 3 (black cable) are short-circuited once and then disconnected. Thus, the sensor recognizes
that the position is 0 °. If the same operation is repeated a second time, the sensor is reset to the factory settings.
During the operations, the sensor position should be kept constant for approximately 4 seconds.
KK-INC.002 10.02.21 Rev No:3
2
AXES AND OUTPUT SIGNAL DIAGRAM
X Axis-Analog Signal Output
Y Axis-Analog Signal Output
KK-INC.002 10.02.21 Rev No:3
3
Supply Voltage
4-20 mA : 12 … 24 VDC
0-10 VDC: 15 … 24 VDC
Protection Class
IP67
*Measurement Range
±90⁰
Operating
Temperature
- 30°C …+70°C
*Measurement Axes
X, XY
Relative Humudity
%10 … %90
*Output Signals
Analog 4-20 mA or 0-10 VDC
Weight
~140 gr
Resolution
12 bit
Body Material
Aluminium
Accuracy
±0,1⁰
*Electrical
Connection
M12 5 pin (male) socket or cable
output
Note: The specifications specified by (*) vary depending on the model selected. The detailed code table for product selection is shown on page 4.
Product
Description
INC 110
Inclinometer
User Manual
1 pcs.
DIMENSIONS (in mm)
TECHNICAL SPECIFICATIONS
MEKANİK MONTAJ
The product must be fixed to the area to be taken inclination
measurement with 4 pcs M6 bolts and nuts.
Warning: All welding work in the relevant area must be
completed before the product is installed. Otherwise, the
device may be damaged during the welding process, and in this
case, it will be out of warranty.
BOX CONTENTS
MECHANICAL MOUNTING
KK-INC.002 10.02.21 Rev No:3
4
Output Type
No code : Single Output
Electrical Connection (3)
3M : 3m cable
5M : 5m cable
10M : 10m cable
S13F : M12 5 pin female socket
S13M : M12 5 pin male socket
Output Signals
V: 0-10 VDC
A: 4-20 mA
Measurement Range (2)
90: ±90°
45: ±45°
Number of axes
01: Single axis
02: Two axes
Sensor Type
E: Inclination
Supply Voltage (1)
PP: 12…24VDC /
15…24VDC
Output Signal Direction
CW: Clockwise
CCW: Counter-Clockwise
Disposal of Packagings: Packaging materials consist of recyclable materials. For providing recycling, please dispose
waste packagings to collecting points of authorized recycling facilities.
Disposal of E-Waste: This device is in conformity with WEEE Directive and consists of recyclable materials. This
product should not be disposed with general waste for preventing negative effects on enviroment and human
health. This product should be disposed to collecting points of authorized recycling facilities. Further information
can be reached from authorized unit.
.
Manufacturer Firm’s Title, Address Details
Manufacturer Firm: ATEK ELEKTRONİK SENSÖR TEKNOLOJİLERİ SANAYİ VE TİCARET A.Ş.
Address: Gebze OSB Mahallesi, 800. Sokak, No:814/1 Gebze, KOCAELİ/TURKEY
TEL: +90 262 673 76 00 FAX: +90 262 673 76 08
Authorized Service’s Title, Address Details
Authorized Service: ATEK ELEKTRONİK SENSÖR TEKNOLOJİLERİ SANAYİ VE TİCARET A.Ş.
Address: Gebze OSB Mahallesi, 800. Sokak, No:814/1 Gebze, KOCAELİ/TURKEY
TEL: +90 262 673 76 00 FAX: +90 262 673 76 08
E-mail: [email protected]
INC 110 X XX XX XX XXX XX XX XX
PRODUCT CODE TABLE
Model
INC 110
(1) The supply voltage is 12…24VDC for 4-20 mA output models, and 15…24VDC for 0-10 VDC output models.
(2) Optionally, different measurement values between ±90° can be requested. You should specify your non-standard measurement value
at the order stage.
(3) The product can be requested with cable or socket.
As standard;
1 pcs M12 5 pin male socket (S13M) is used.
However, different socket combinations may be requested as in the examples below.
Please contact us for any other socket model other than M12.
Sample Code 1: INC110-E-01-90-PP-A-CW-S13F
INC 110 series, inclination, single axis, ±90°measurement, 12-24VDC supply, current output, clockwise, 1 pcs M12 5 pin female soke
Sample Code 2: INC110-E-02-45-PP-V-CCW-S13M
INC 110 series, inclination, two axes, ±45°measurement, 15-24VDC supply, volt output, counter-clockwise, 1 pcs M12 5 pin male
socket
This manual suits for next models
1
Table of contents
Other Atek Accessories manuals
