Asus AAM6000PI User manual

AAM6000PI

ADSL Modem Card

Table of Contents

Congratulations! ................................................................................................... 1

Step 1 – Know your PC’s Operating System ................................................... 1

Step 2 – Determine your Connection Settings.................................................. 2

Step 3 – Install the ADSL Modem Card........................................................... 3

Step 4 – Install the Drivers and Make a Connection....................................... 4

Windows 95A....................................................................................................... 5

Windows 95B ....................................................................................................... 8

Windows 98, 98SE............................................................................................. 12

Making a RFC 1483/1577 connection - 95A, 95B, 98, 98SE .................... 15

Making a RFC 2364 connection - 95A, 95B, 98, 98SE ..............................17

Windows 2000.................................................................................................... 19

Making a RFC 1483/1577 connection - 2000 ............................................ 22

Making a RFC 2364 connection - 2000 ...................................................... 24

Windows NT4.0 - RFC 1483/1577 .................................................................... 26

Windows NT4.0 - RFC 2364 ............................................................................. 29

Appendix

Editing your Service Connection........................................................................ 33

Removing Drivers .............................................................................................. 34

Diagnostic Tools ................................................................................................ 35

Trouble Shooting................................................................................................ 37

Connector Pin-out............................................................................................... 38

System Requirements & Compliance information.............................................. 39

Congratulations!

You are about to accelerate into ADSL technology. Your new ADSL modem card is an

internal Asymmetric Digital Subscriber Line (ADSL) PCI modem card, which

conveniently plugs into your computer system. The

modem connects directly to your telephone line via a

standard connector.

This guide is designed to walk you through installation of

your ADSL Modem card in the easiest and quickest way

possible. Please follow the instructions carefully.

Step 1 – Know you PC’s Operating System

You will need to know the exact version of Microsoft Windows installed in your

computer. If you do not know or are unsure, please proceed as follows to determine your

version of the Microsoft Operating System.

On the desktop, right click My Computer. Then select Properties. The version number

of the Microsoft Windows Operating System installed in your computer will be displayed

on the General tab. Refer to the following table for more detailed information.

Windows OS System Properties Description Release (Microsoft Web)

Win 95A

4 00 950A

Windows 95 OSR1

Win 95B 4.00.950B Windows 95 OSR2

Win 98 4.10.1998 Window 98

Win 98SE 4.10.2222A 2nd Edition Windows 98 2nd Edition

Win 2000 5.00.2195 Windows 2000

Win NT 4.00.1381 Windows NT 4.0

If you have questions regarding your PC system and the Microsoft Windows Operating

System, please contact your original PC manufacturer or Microsoft for assistance.

Before Installing the ADSL PCI Modem Card, it is important to verify that the ADSL data port RJ-

11 jack is configured so that the center two pins, pins 3 and 4, are used for ADSL data, otherwise

the ADSL PCI modem card will not make a proper connection. If the ADSL data port installation

uses pins 2 and 5 for data, then a wiring converter will be required. Do not alter or remove a wiring

converter if present. Consult with your ADSL service provider regarding a wiring converter or

before attempting any wiring changes.

Step 2 – Determine your Connection settings

You need to know your PC systems Windows OS and Internet Protocol supplied by

your ADSL service provider. Refer to the following chart for your ADSL Driver.

Protocol Selection

RFC1483 Ö

ÖÖ

Ö



Bridged Ethernet over ATM

RFC2364 Ö

ÖÖ

Ö



Point-to-Point Protocol over ATM

RFC1577 Ö

ÖÖ

Ö



Classical Internet Protocol over ATM

RFC2516 Ö

ÖÖ

Ö



Point-to-Point Protocol over Ethernet

ADSL Driver Selection RFC1483 RFC2364 RFC1577 RFC2516

Win 95A & 95B 1483w95 2364w95 See Note#

Win 98 & 98SE 1483w98 2364w98 1577w98

See Note#

Win NT 4.0 1483nt4 2364nt4 See Note#

Win 2000 1483w2k 2364w2k See Note#

Note#

#: RFC2516 (Point-to-Point Protocol over Ethernet) is supported by third

party developers. See the PPPoE driver supplement for detailed information and

installation instructions.

Having determined the ADSL Driver you will be installing, you now need to gather the

connection information supplied by your ADSL service provider.

VPI value:_________

VCI value:_________

Framing: VC/MUX LLC/SNAP

Mode: ANSI T1.413 ITU G.lite ITU G.dmt

For RFC 1483 or 2516 For RFC 2364 or 1577

Host: User Name:

Domain: Password:

Gateway: Host or IP Address:

IP Address:

Subnet Mask:

DNS or server address:

Step 3 – Install the ADSL modem card

Caution: To avoid possible damage to your modem card, touch the metal chassis of your

PC system to remove static charge from your person, and then remove your ADSL

modem card from the protective anti-static bag.

1. Shut down your computer and switch the

power off.

2. Unplug the power cord for your

computer from the electrical outlet.

4. Unscrew “slot cover bracket” from an

unused PCI (usually white in color) slot.

6. Make sure the card is firmly seated and

secure the card with the bracket screw.

3. Remove the cover from your systems

chassis. (see you PC manufacturer’s

manual)

5. Gently and evenly insert the PCI

modem card into your empty PCI slot.

7. Replace the cover of your computer

system.

8. Connect the ADSL/phone line to the

connector port on the modem card and

plug the other end of the cable into

your ADSL/phone service.

Step 4

– Install the drivers and make a connection

You will be installing drivers and then proceeding to make an Internet connection. This

process requires you to enter in information as prompted by the Microsoft Installation

Wizard.

NOTE:You may need the Microsoft Windows Operating System installation files (CAB

files) to complete the installation. The CAB files are contained in the Microsoft’s system

CD-ROM. Some systems may have already installed the CAB files to the hard drive, but

you should have the Microsoft Windows CD-ROM handy just in case.

Proceed now to the installation procedure for the Windows Operating

System installed in your computer.

Windows 95A -------------------------------------------------------------------------------Page 5

Windows 95B -------------------------------------------------------------------------------Page 8

Windows 98, 98SE------------------------------------------------------------------------- Page 12

Windows 2000 ------------------------------------------------------------------------------Page 19

Windows NT - RFC 1483 or RFC 1577 -----------------------------------------------Page 26

Windows NT - RFC 2364----------------- -----------------------------------------------Page 29

Windows 95A

After installing the ADSL modem card, plug the power cable back into the PC system

and turn the power on.

Before you proceed to install drivers you will need to upgrade your Dial-Up Networking

(DUN) application to version 1.3 or above. The Microsoft DUN is conveniently

contained on your ADSL Driver CD-ROM.

1. After restart, the Update Device Driver

Wizard will detect the ADSL modem as a

PCI Network Controller. CANCEL the

New hardware found window.

2. At your desktop, click Start, and then

select Run.

3. The

Run window appears. Insert the

ADSL Driver CD, then click on Browse

and proceed to locate the ADSL Driver

95 CD-ROM. Then locate and select the

MSDUN13.EXE file. The Msdun13.exe

appears in the Open box. Click OK.

4. The

Microsoft Dial-Up Networking 1.3

window appears with the message This

will install Microsoft Dial-Up

Networking 1.3 for Windows 95. Do

you wish to continue? Click Yes.

5. An

End-User License Agreement will

appear. To accept, click Yes.

6. Back in the Microsoft Dial-Up

Networking 1.3 window. You will be

asked Do you want to restart your

computer now? Click Yes.

NOTE:You may need the Microsoft Windows Operating System installation files (CAB

files) to complete the installation. The CAB files are contained in the Microsoft’s system

CD-ROM. Some systems may have already installed the CAB files to the hard drive, but

you should have the CD-ROM handy just in case.

1. The

New Hardware Found window will

detect the ADSL modem card as a PCI

Network Controller. Select the Driver

from disk provided by hardware

manufacturer option. Click OK.

2. Insert the

ADSL Driver CD-ROM into

your systems CD drive.

3. The

Install From Disk window appears.

Click Browse to locate the driver on your

CD-ROM for the protocol supported by

your ADSL provider: 1483w95 or

2364w95 or 1577w95 (The example uses

“D” as the CD-ROM drive letter. Your

drive may have a different letter.) Then

click OK.

4. When the

Service Option window

appears, click Advanced.

5. The

Service Options window displays

the Connection Address and Select

ADSL Mode sections. Enter in the VPI,

VCI and Framing values supplied by

your ADSL service provider.

In the Select ADSL Mode section, select

the mode(s) recommended by your ADSL

service provider. Click on the mode(s)

required and then click OK.

NOTE: The service mode type will be one of

the following:❑ANSI T1.413 Issue 2

❑ITU G.992.2 Annex A(G.lite)

❑ITU G.992.1 Annex A(G.dmt)

RFC 1483

RFC 1577

RFC 2364

6. The previous

Service Option window

will appear, click Next.

NOTE:During the installation process

you may be asked to insert your

Windows 95 CD. Insert the Windows

95 CD into the CD drive and click OK.

NOTE: If during the file copying

process a file is reported as “not found”

enter the path <CD Drive letter> and

:\Win95 (e.g. D:\Win95)

7. You must now make an Internet connection. Locate the Internet protocol supported

by your ADSL service provider from the following table, and proceed to that section

to make the Internet connection.

FC1483 Bridged Ethernet over ATM Ö

ÖÖ

Ö



Go to page 15

FC1577 Classical Internet Protocol over ATM Ö

ÖÖ

Ö



Go to page 15

FC2364 Point-to-Point Protocol over ATM Ö

ÖÖ

Ö



Go to page 17

Windows 95B

After installing the ADSL modem card, plug the power cable back into the PC system

and turn the power on.

Before you proceed to install drivers you will need to upgrade your Dial-Up Networking

(DUN) application to version 1.3 or above. The Microsoft DUN is conveniently

contained on your ADSL Driver CD-ROM.

1. After restart, the Update Device Driver

Wizard will detect the ADSL modem

card as a PCI Network Controller.

CANCEL the New hardware found

window.

2. At your desktop, click Start, and then

select Run.

3. The

Run window appears. Insert the

ADSL Driver CD, then click on Browse

and proceed to locate the ADSL Driver

95 CD-ROM. Then locate and select the

MSDUN13.EXE file. The Msdun13.exe

appears in the Open box. Click OK.

4. The

Microsoft Dial-Up Networking 1.3

window appears with the message This

will install Microsoft Dial-Up

Networking 1.3 for Windows 95. Do

you wish to continue? Click Yes.

5. An

End-User License Agreement will

appear. To accept, click Yes.

6. Back in the Microsoft Dial-Up

Networking 1.3 window. You will be

asked Do you want to restart your

computer now? Click Yes.

Table of contents

Popular Network Card manuals by other brands

FirstComm

FirstComm OBiWiFi5G Setup guide

Sun Microsystems

Sun Microsystems Interface Adapter user guide

TRENDnet

TRENDnet TU2-ETG user guide

YASKAWA

YASKAWA SI-EN3 Technical manual

Paradyne

Paradyne BitStorm 2600 IP DSLAM installation guide

Belkin

Belkin F5D7050 user manual

3Com

3Com EtherLink 3C509B quick guide

TRENDnet

TRENDnet TEG-PCITX user guide

Cisco

Cisco MC16E installation guide

Delta Electronics

Delta Electronics Braking Modules VFDB Series instruction sheet

TwinMOS

TwinMOS Booming user manual

Dialogic

Dialogic Media Board DM/V1200BTEPEQ installation guide

Buffalo

Buffalo AirStation WLI-PCM-L11GP user manual

National Instruments

National Instruments NI 9234 operating instructions

Hama

Hama 49276 Operating instruction

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Product data

Compaq

Compaq Wireless LAN 100 specification

Bose

Bose PowerMatch Dante quick start guide