Assa Abloy Aperio Series User manual
Page 1 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Products Specifications
Wireless Frequency: 2.4GHz, IEEE 802.15.4, using AES 128-bit encryption
Lock Battery Type: AA Lithium, 1.5 Volts (V)
Battery Life: 50,000 cycles*
*All battery life claims are approximate and based on a set configuration profile. Battery performance is based on pre-defined system settings such
as battery chemistry and battery model used, credential presentation settings (LED/buzzer), UHF polling period, UHF status intervals, and
operations per day. Actual battery performance will vary and depends on the factors above.
Operating Temperature: 32to 122F (0to 50C)
HID® multiCLASS SE® technology Credentials Supported:
High Frequency (13.56 MHz):
HID iCLASS®
HID iCLASS SE®(SIO-enabled)
HID iCLASS®Seos™
HID MIFARE®SE
HID DESfire®EV1 SE
MIFARE CLASSIC
DESfire®EV1
Low Frequency (125 kHz):
HID Prox®, AWID, EM4102, ioProx
NFC-enabled Mobile Phones
AA Lithium Batteries
required. Use of other
types of batteries, such as
alkaline, will significantly
decrease battery life.
2x
HES K100 AperioSeries
Wireless Cabinet Lock
Installation and Operating Instructions
Page 2 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Recommended Tools
Flathead Drivers —3/32”, 3/16”
Drill, Drill Bits —1/16”, 3/16”, 1/2”
Phillips Drivers —P0, P2
Pencil, Wire Stripper, Level, Square, Ruler, Punch, Scissors
Hardware Specifications
Table 1 –Shaft Length
Table 2 –Mounting Screw Length for Various Door Thickness
Door
Thickness
Reader
Mounting
Cut to
approx.
screw
length
Lock
Mounting
Cut to
Approx.
Screw
Length
1/16”
Coupling Nut
and 3” Rod
10/16”
8-32 x 1-3/4”
Break Away
1-1/16”
1/4"
Coupling Nut
and 3” Rod
13/16”
8-32 x 1-3/4”
Break Away
1-1/4”
1/2”
Coupling Nut
and 3” Rod
1-1/16”
8-32 x 1-3/4”
Break Away
1-7/16”
3/4”
Coupling Nut
and 3” Rod
1-5/16”
8-32 x 1-3/4”
Break Away
No Cut
1”
Coupling Nut
and 3” Rod
1-9/16”
8-32 x 2-1/2”
2”
1-1/4”
Coupling Nut
and 3” Rod
1-13/16”
8-32 x 2-1/2”
No Cut
1-1/2”
Coupling Nut
and 3” Rod
2-1/16”
8-32 x 2-3/4”
No Cut
For Technical Support Please call 1-800-810-WIRE
Door Thickness
Shaft Used
1/16” – 1/2”
L1
>1/2” – 1½”
L2
>1½” – 2¼”
L3
Page 3 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Package Contents
6 X 1/2"
6x
(D)
6-32 X 5/16”
3x
(C)
8-32 X 5/16”
(B)
2-56 X 7/16”
2x
(A)
Reader
Lock Body
Strike Plate
Installation
Template
Mechanical Key Override
Hardware
8-32 X 2-1/2”
2x
(G)
8-32 X 2-3/4”
2x
(E)
8-32 X 1-3/4”
2x
(F)
Lithium Batteries
2x
Double Door
Bracket
8-32 X 3”Rod
(H)
8-32 Nut
(J)
Threadlock
Pillow Pack
Page 4 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Lock Orientation Options
Prepping the Cabinet/Drawer Face
1. Separate Strike Plate Template.
2. Establish centerline (for double door
cabinet prep go to page 6).
Orientation A
Orientation B
Orientation C
Page 5 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
3. Measure cabinet wall thickness and mark
offset line on face of cabinet/drawer. The
offset line should match with the interior
edge of the cabinet wall.
4. Continue centerline to face of
cabinet/drawer
5. Align template to offset line and
centerline. Remove backing and apply
template onto cabinet/drawer face.
6. Use punch to mark drilling
locations then drill mounting holes. If
using mechanical key override, drill
key override hole as well.
Center
line
Offset Line
Page 6 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Prepping the Cabinet/Drawer Face (Double Door)
3. Align offset line on template to the edge of the stationary door and align center
line with the established center line above. Remove backing and apply template to
cabinet face. Continue with Step 6 in previous section.
1. Establish center line on inside
of stationary door.
2. Continue center line onto
outside face of cabinet.
Page 7 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Reader Installation
1. Align reader with mounting holes and pull
cable through as shown. Trim Threaded rod
to length as outlined in table 2.
2. Add Threadlock to threaded rod.
Secure Reader to cabinet/drawer using
the cut threaded rod and coupling nut.
DO NOT overtighten.
Mechanical Override (Optional)
1. Slide Override into slot as shown.
2. Ensure that override retracts latch
bolt before installation. Override
should rest loosely until lock body and
battery cover are installed.
Page 8 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Lock Body Installation
1. Insert reader cable through hole
in back of lock body.
2. Align lock body to mounting holes
andsecure to cabinet/drawer face using
2x screw F and 2x screw D. If thick
cabinet/drawer then use 2x screw E or
2x screw G instead of 2x screw F. DO
NOT over tighten.
3. Plug cable into slot on lock body.
4. Tuck excess cable into lock body
cavity as shown.
5. Any excess cable should be inserted
into the cavity as shown below.
6. For cabinet/drawer face thicker
than1/2”, add a third screw D as
shown.
Page 9 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Installing the Batteries
1. Install AA lithium batteries in appropriate
position.
2. Install cover and secure using 2x
screw A.
Mechanical Key Override (Optional)
Mechanical key override cam lock sold
separately.
1. Insert cam lock through the outside
of the cabinet/drawer face and secure
with locking nut. Insert the end of Cam
into the mechanical override and secure
with nut as shown.
Important Note–Reader MUST be programmed before installing the strike plate. If the cabinet
is closed before the reader is programmed and after the strike plate is installed, you will be locked out of
the cabinet.
Page 10 of 16 For more information visit website assaabloyesh.com P/N: 3080006.016 Rev1
Strike Plate Installation
1. Align strike plate template to centerline
and edge of cabinet. Drill mounting holes.
2. Secure strike plate to inside cabinet
wall using 2x screw D, but do not fully
tighten. Adjust strike plate so the edge
is flush with the cabinet wall edge then
tighten.
3. After the strike plate is in the desired position, fasten screw D into strike plate as
shown below.
This manual suits for next models
1
Table of contents
Other Assa Abloy Lock manuals
Assa Abloy
Assa Abloy hes 8000 Series User manual
Assa Abloy
Assa Abloy SARGENT 1655 User manual
Assa Abloy
Assa Abloy Sargent L980S User manual
Assa Abloy
Assa Abloy effeff EX118R User manual
Assa Abloy
Assa Abloy OneSystem 319N Installation instructions
Assa Abloy
Assa Abloy OneSystem Espagnolette User manual
Assa Abloy
Assa Abloy Medeco XT User manual
Assa Abloy
Assa Abloy Lockwood 3579 Series User manual
Assa Abloy
Assa Abloy Sargent FM6100 Series User manual
Assa Abloy
Assa Abloy SECURITRON MORTISE UNLATCH MUNL-12 User manual
Assa Abloy
Assa Abloy Sargent PE80 Series User manual
Assa Abloy
Assa Abloy PULSE PK200 User manual
Assa Abloy
Assa Abloy ML53PA User manual
Assa Abloy
Assa Abloy EMTEK A User manual
Assa Abloy
Assa Abloy HES 5000 Series Manual
Assa Abloy
Assa Abloy Sargent ELR Series User manual
Assa Abloy
Assa Abloy SARGENT Profile LK Series Installation manual
Assa Abloy
Assa Abloy HES K20 User manual
Assa Abloy
Assa Abloy Yale Smart Latch User manual
Assa Abloy
Assa Abloy OneSystem 819N User manual
