Assa Abloy ML52RA User manual

Electro-mechanical Lock Model ML52RA

ASSA ABLOY SENSE

USER OPERATION

Up to 60 cards can be added to the lock. These cards can be assigned to the lock as either user cards,

Janitor Cards or Master Cards.

A. PRIVATE MODE

In Private Mode the lock is set to work with the same user cards(s). These cards needs to be previously

registered to this specific lock. In Private Mode up to 5 Master Cards and 55 User Cards can be added.

1: To open the lock, simply present your registered User Card and open the door. If the handle isn’t turned,

the lock will automatically re-lock after 4 seconds.

2: To close, simply turn the handle into locked position and the lock will automatically lock.

B. PUBLIC MODE

In Public Mode the lock is set to work with any Compatible Card that is presented to the lock. This will tem-

porarily register this card to the lock. Upon opening the lock with this card, the lock will remove this as the

Registered Card, and any other Compatible Card can now operate the lock. In Public Mode up to 5 Master

Cards and 50 Janitor Cards can be added.

1: To close, turn the handle into locked position and present a Compatible Card. This will lock the lock.

Other cards cannot now operate the lock.

2: To open, present your Registered Card to the lock. Any other card can now operate the lock.

MASTER CARD OPERATION

The Master Cards can open the lock in both modes. In Public Mode, opening with the Master Card, will also

erase any Registered Card from the lock and leave the lock in open position.

JANITOR CARD OPERATION

The Janitor Cards can open the lock in Public Mode. Different to the Master Card, the Janitor Card will not

erase the registered User Card. When opening with the Janitor Card the lock will automatically re-lock.

FACTORY RESET

Insert a needle or clip through the hole on the back and press for 2 seconds. This will restore the lock into

Factory Mode, see lock setup for different options on how to reprogram the lock into desired configuration.

In Factory Modes the quick setup options are also available.

LOW BATTERY

When the battery level drops below 10%, 3 red flashes will occur after opening the lock. Please change

batteries at this point.

EXTERNAL POWER SUPPLY

Use external 5-pin USB power if the battery is dead and the lock does not respond at all

(Use with smartphone/laptop charger).

PROGRAMMING CARDS

The following cards are used when programming the locks

Add / Remove User Cards

Add / Remove Master Card Add /

Remove Janitor Card

Switch between Private and Public Mode

CCopying Card

BASIC SETUP

When the lock is in Factory Mode (on delivery and after factory reset) and the battery is entered the

following options on how to deploy the lock is available.

A: QUICK SETUP OF MASTERCARD AND USER CARDS FOR USE IN PRIVATE MODE

First present a Compatible Card which will become a new Master Card. Then within 5 seconds present a

second card which will be registered as the first User Card. Continue to present cards within 5 seconds after

the previous registration to add additional User Cards. Then wait 5 seconds and the lock will go into Private

Mode. Further programming is then done by using the Programming Cards.

The sequence below describes an example of how to add one Master Card (1) and two User Cards (2 and 3). Up to

50 User Cards can be registered to each lock.

Enter batteries 1

(Within five seconds)

(Wait five seconds)

B: QUICK SETUP OF MASTERCARD FOR USE IN PUBLIC MODE

Present first Compatible Card which will become the Master Card. Then wait 5 seconds and the lock will go

into Public Mode. Further programming is then done by using the Programming Cards.

The sequence below describes an example of how to add one Master Card (1) for use in Public Mode.

Enter batteries: 1

(wait five seconds)

C: USING THE COPYING CARD

STEP 1: Read the setup of a programmed lock and record it to the Copying Card

C(During reading) (After reading completed)

Ex: Present a Copying Card followed by the Master Card and present the Copying Card again for reading the setup

of the lock.

NOTE1: No information of registered User Cards will be read into the Copying Card. User Cards always have

to be registred individually to the locks.

NOTE 2: The card needs to be cleared before beginning this procedure, see special commando 34.

On delivery, the card is cleared.

STEP 2A: Programming locks with the Copying Card into Public Mode

A lock in factory mode will read the setup on the Copying Card. This can be repeated for as many lock as

required.

The sequence below describes an example on how to use the Copying Card to set up lock in Public Mode.

Enter batteries:

C(During programming) (After complete programming)

Further programming on this lock is now done with the programming cards. See Lock Programming.

STEP 2B: Programming locks with the Copying Card into Private Mode

A lock in Factory Mode will read the setup on the Copying Card. After that the setup it’s possible to present

Compatible Cards to register them as User Cards. This can be repeated for as many lock as required.

The sequence below describes an example on how to use the Copying Card to set up the lock in Private Mode.

In this case 2 User Cards are also registered.

Enter batteries:

C(During programming) (Within five seconds)

(Within five seconds)

(Continue to present cards or wait 5 seconds

to end programming)

Further programming on this lock is now done with the programming cards. See Lock Programming.

Electro-mechanical Lock Model ML52RA

ASSA ABLOY SENSE

LOCK PROGRAMMING

1: USER CARDS (ONLY IN PRIVATE MODE)

1A: Add 1 User Card

(Wait 5 seconds or touch Master Card)

Ex: Present Programming Card 1 followed by a Master Card. Then present a Compatible Card to register this as a new

User Card.

1B: Delete 1 User Card

(Wait 5 seconds or touch Master Card)

Ex: Present Programming Card 1 followed by a Master Card. Then present a registered User Card to remove this from

the lock.

1 C: Add Multiple Cards

(Within five seconds) (Within five seconds)

(Continue to present cards or wait 5 seconds to end programming)

Ex: Present Programming Card 1 followed by a Master Card. Then present multiple registered User Cards to remove

them from the lock.

1D: Delete Multiple Cards

(Within five seconds) (Within five seconds)

(Continue to present cards or wait 5 seconds to end programming)

Ex: Present Programming Card 1 followed by a Master Card. Then present multiple registered User Cards to remove

them from the lock.

1E: Delete all cards

Ex: Present Programming Card 1 followed by a Master Card. Then present Programming Card 1 again to remove all

User Cards from the lock.

2: MASTER CARDS

2A: Add 1 Master Card

(Wait 5 seconds or touch Master Card)

Ex: Present Programming Card 2 followed by a Master Card. Then present a Compatible Card to register this as a new

Master Card.

2B: Delete 1 Master Card. Any Master Card can delete any other Master Card that is registered to the lock.

A Master Card cannot delete itself thus securing that always one Master Card remains registered.

((Wait 5 seconds or touch master card)

Ex: Present Programming Card 1 followed by a Master Card. Then present another registered Master Card to remove

this from the lock.

2C: Add multiple Master Cards

((Within five seconds) (Within five seconds) (Continue to present cards

or wait 5 seconds to end programming)

Ex: Present Programming Card 2 followed by a Master Card. Then present multiple Compatible Cards to register these

as new Master Cards.

2D: Delete multiple Master Cards. Any Master Card can delete any other Master Cards that is registered to

the lock. A Master Card cannot delete itself thus securing that always one Master Card remains registered.

(Within five seconds) (Within five seconds) (Continue to present cards

or wait 5 seconds to end programming)

Ex: Present programming card 2 followed by a Master Card. Then present multiple other registered Master Cards to

remove them from the lock.

ASSA ABLOY SENSE

Electro-mechanical Lock Model ML52RA

ASSA ABLOY SENSE

2E: Delete all Master Cards except the one used for this programming

Ex: Present Programming Card 2 followed by a Master Card to keep. Then present Programming Card 2 again to

remove all Master Cards from the lock except the Master Card used for this programming.

3: JANITOR CARDS (ONLY IN PUBLIC MODE)

3A: Add Janitor Card

(Wait 5 seconds or touch Master Card)

Ex: Present Programming Card 3 followed by a Master Card. Then present a Compatible Card to register this as a

new Janitor Card.

3B: Delete Janitor Card

(Wait 5 seconds or touch master card)

Ex: Present programming card 3 followed by a master card. Then present a registered janitor card to remove this

from the lock.

3C: : Add multiple Janitor Cards

(Within five seconds) (Within five seconds) (Continue to present

cards or wait 5 seconds to end programming)

Ex: Present Programming Card 3 followed by a Master Card. Then present multiple Compatible Cards to register these

as new Janitor Cards.

3D: Delete multiple Janitor Cards

(Within five seconds) (Within five seconds) (Continue to present

cards or wait 5 seconds to end programming)

Ex: Present Programming Card 3 followed by a Master Card. Then present multiple registered Janitor Cards to remove

them from the lock.

3E: Delete all Janitor Cards

Ex: Present programming card 3 followed by a Master Card. Then present Programming Card 3 again to remove all

Janitor Cards from the lock.

4: SWITCH BETWEEN PRIVATE AND PUBLIC MODE

4A: Switch to Public Mode

4B: Switch to Private Mode

NOTE 1: This programming toggles between Private and Public Mode. The LED indicates which mode the lock is

being set to.

NOTE 2: If switching to Public Mode all registered User Cards are deleted. If switching to Private Mode, all Janitor

Cards are deleted. Lock will remain unlocked until first User Card is added.

Electro-mechanical Lock Model ML52RA

ASSA ABLOY SENSE

Electro-mechanical Lock Model ML52RA

OTHER PROGRAMMING

12 OCH 13: ALLOW/DISALLOW TO LOCK MORE THAN ONE LOCK WITH THE SAME CARD (PUBLIC MODE)

Double locking means that a card can lock more than 1 lock in public mode. If disallowed, a card that is registered to one

lock, cannot close another lock before it has opened the first lock. As default double locking is allowed. The function of disal-

low cards to lock more than one lock is NOT available with Mifare DESfire-cards.

12: Allow double locking (default setting)

13: Disallow double locking

NOTE 1: If lock is set to disallow double locking it is not possible to use Cards with locked sectors, as this setup requires

that the lock can write to the card.

21 AND 23: TURN SOUND ON AND OFF

21: Turn sound on

23: Turn sound off (default setting)

34: RESET USER CARDS THAT IS LOCKED

In case the Master Card is used to open a lock in Public Mode with double locking disallowed, this will unregister the card

from the lock, but the card will be locked. This card can now no longer be used unless it’s cleared of its registration. To do

this, use the following procedure.

34: Reset User Cards for use in public mode

(Within five seconds)

3(Continue to present cards for reset or

wait five seconds to end reset procedure)

Ex: Present programming card 3 followed programming card 4 .Then present any locked user cards to reset them.

ASSA ABLOY Opening Solutions Sweden

P.O. Box 371

SE-631 05 Eskilstuna

Sweden

Phone +46 (0)16 17 70 00

Fax +46 (0)16 17 70 49

Customer support:

Phone intl. +46 (0)16 17 71 00

Phone nat. 0771-640 640

Fax +46 (0)16 17 73 72

e-mail: helpdesk.se.openingsolutions@assaabloy.com

www.assaabloyopeningsolutions.se

We reserve the right to correct any printing errors and update the information after printing.M4177.1912

ASSA ABLOY SENSE

Electro-mechanical Lock Model ML52RA

UPDATE LOCK WITH COPYING CARD

In the case you want to do a quick update of the lock settings for a larger number of locks, the copying card can be used. You

first need to update 1 lock to the desired settings and then follow the steps below.

NOTE: No information of registered User Cards will be read onto the Copying Card. When using the Copying Card to update

the lock no User Cards will be removed or added. For adding/removing User Cards, see lock programming, section 1.

STEP 1: Clear the Copy Card

This is necessary in order to get step 3 to work properly.

C(During clearing of card) (Card cleared)

Ex: On any lock, present the switch card followed by the Copying Card to clear it from any data.

STEP 2: Read the setup of an updated lock and record it to the Copying Card (same as in section C)

C(During reading) (Complete reading)

Ex: Present a Copying Card followed by the Master Card and present the Copying Card again for reading the setup of the lock.

STEP 3: Update the setup of a programmed lock (repeat for all locks that needs to be updated)

NOTE: For security reasons, this requires that at least one Master Card that is registered on the lock that is to be updated, is

also copied onto the Copying Card.

C(During update) (Update complete)

Ex: Present a Copying Card to update the lock settings.

Table of contents

Other Assa Abloy Door Lock manuals

Assa Abloy

Assa Abloy Yale Real Living YRDZW Technical specifications

Assa Abloy

Assa Abloy effeff Mini Shear Magnet User manual

Assa Abloy

Assa Abloy Corbin Russwin SE LP10 9600 Series User manual

Assa Abloy

Assa Abloy Sargent Passport 1000 PG User manual

Assa Abloy

Assa Abloy Corbin Russwin Access 600 CL33600 TCRNE1... User manual

Assa Abloy

Assa Abloy PEMKO LP200 Series User manual

Assa Abloy

Assa Abloy Sargent PE8300 Series User manual

Assa Abloy

Assa Abloy Sargent IN220 User manual

Assa Abloy

Assa Abloy Securitron TSH Series User manual

Assa Abloy

Assa Abloy SARGENT BL7300 Series User manual

Assa Abloy

Assa Abloy VERSO CLIQ V532 User manual

Assa Abloy

Assa Abloy Corbin Russwin CLX3361 User manual

Assa Abloy

Assa Abloy Securitron Magnalock M670BD Series User manual

Assa Abloy

Assa Abloy SARGENT FM7100 Series User manual

Assa Abloy

Assa Abloy Corbin Russwin Access 800 9800 TCWI1 Series User manual

Assa Abloy

Assa Abloy HES 9400 Operating instructions

Assa Abloy

Assa Abloy 179E-2 User guide

Assa Abloy

Assa Abloy Sargent 7800 Series User manual

Assa Abloy

Assa Abloy ESA500 Installation manual

Assa Abloy

Assa Abloy effeff 827A-IP User manual

Assa Abloy

Assa Abloy Yale PBS1 User manual

Assa Abloy

Assa Abloy Effeff EX118P Series User manual

Assa Abloy

Assa Abloy Valencia AJAX User manual

Assa Abloy

Assa Abloy Yale Doorman User manual

Popular Door Lock manuals by other brands

We.lock

We.lock SECBNEBL51 instructions

Iseo

Iseo MA1A installation guide

ID Lock

ID Lock 150 user manual

Lockly

Lockly ACCESS TOUCH PRO user manual

iLoq

iLoq G50S user guide

SDC

SDC Z7835 installation instructions

ilco

ilco 452 Installation

Samsung

Samsung shs-h705 user guide

TRU-BOLT

TRU-BOLT 08102017 user manual

CDVI

CDVI 500-LADJ quick start guide

Igloohome

Igloohome Deadbolt 2S Metal Grey Installer/user guide

eSSL

eSSL FL-300 user manual

JAKO

JAKO JKBTNX4 installation guide

Dorma

Dorma MUNDUS PREMIUM GK 50 Mounting instruction

SCOOP

SCOOP Pullbloc 4.1 FS Panik Assembly instruction

Yale

Yale MORTISE 8800 SERIES installation instructions

Siegenia

Siegenia KFV AS3500 Assembly instructions

Saflok

Saflok Quantum ädesē RFID installation instructions