Asko D5894XXLFI User manual
The drain hose is fastened to the back of
the machine at the best height. To eliminate
potential drain problems, leave this hose in
place.
IMPORTANT!
Read all of these instructions before
installing the dishwasher.
Page 2 Customer Care Center
1-800-898-1879
www.askousa.com
1) Phillips No. 2 screwdriver
2) Flat blade screwdriver
3) Torx screwdriver size T 20
4) Adjustable wrenches (if you use copper ttings)
5) Open-ended wrench (1/2˝ [12 mm] or 5/8˝ [16 mm])
6) Tape measure
7) Spirit level
8) Electric drill with 1-1/2˝ drill bit
9) Keyhole saw
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualied person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
If a dishwasher is being installed in this area for the rst
time, most of the cabinet work, plumbing, and electrical
has to be done before you move the machine into place.
Cosmetic damage must be reported to the ASKO
dealer within ve days from the date of purchase.
As soon as you unpack the dishwasher, thoroughly
check it for cosmetic damage.
If you are replacing an old dishwasher, you must check
the plumbing connection and wiring before you move the
new dishwasher into place.
• Minimum 3/8" OD copper tubing of sucient length
for your installation
• Shut-o valve and ttings for water supply line
* Only select models.
2x
1"
(25 mm)
2x
3/8"
(10 mm)
6x
1-1/2"
(38 mm)
2x
4x / 3x
1
4
5
7
6
2
3
*
*
Page 3 Customer Care Center
1-800-898-1879
www.askousa.com
• It is important that you closely follow the instructions
provided here.
• An incorrect or defective installation can lead to
higher consumption of energy, water and dishwashing
detergent, which can lead to higher costs and poor
cleaning results.
• Plumbing and electrical installations must be carried
out by qualied professionals.
• Exercise caution during the installation! Wear protective
gloves! Always work in pairs!
• The power outlet for the dishwasher should be
installed in a location that is easily accessible once
the dishwasher is installed.
• Always follow the applicable regulations for water, drain
and electrical connection.
• If a dishwasher must be hard wired, it must be
connected to a grounded circuit.
Turn off the water supply when installing the dishwasher!
• There must be a shut o valve on the water supply pipe.
The shut o valve should be installed in a location that
is easily accessible so that the water may be shut o
in the event that the dishwasher needs to be moved.
• Cable holes for wires/cables need not be larger than
1-1/2˝ (38 mm).
• Attach the light shielding film (see FITTING THE
DISHWASHER IN PLACE). Only select models.
Check that the tting and connection measurements are
correct. See UNIT DIMENSIONS and PREPARING THE
LOCATION.
Page 4 Customer Care Center
1-800-898-1879
www.askousa.com
Height (Adjustable) 33-7/8˝ to 36˝ 860 mm to 914 mm
Width 23-5/8˝ 600 mm
Depth (Includes high loop) 22-7/8˝ 581 mm
Depth W/Door Open 49-1/2˝ 1257 mm
Weight 110 Ib 50 kg
Electricity 120V, 60Hz, 15 amp
Water pressure 4.2 - 140 psi,
0.03-1.0 MPa,
0.3-10 Bar
Heating element 1200 watt
Max loading 1300 watt
33-7/8" to 36"
860 mm to 914 mm
2-7/8"
73 mm
3-3/8"
86 mm
49-1/2"
1257 mm
5-3/8" to 7-3/8"
137 mm to 187 mm
23-5/8"
600 mm
22-7/8"
581 mm
9"
229 mm
3-1/8"
79 mm
Door
The best place for your dishwasher is in the kitchen near
the sink. This makes it easier to connect the water and
drain supply lines.
A built-in dishwasher must be enclosed on the top, both
sides and the back.
The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the
undercounter space in whitch the appliance is to be
installed.
The electrical and water supplies should enter through the
area indicated by the shading on the illustration at right.
Preferably, they should come through the right side of the
machine. The access hole must be round and smooth and
no bigger than 1-1/2˝ (38 mm) in diameter. If the partition
is metal, it needs to be covered with an edge protector.
Use caution when the appliance is installed or removed, to
reduce the likelihood of damage to the power-supply cord.
Height** 33-7/8˝ – 36˝ 860 – 914 mm
Width 23-5/8 – 24˝ 600 – 610 mm
Depth 24˝ 610 mm
** If accessory FI ll strips are used, then 1/2˝ (13 mm) must
be added to the dishwasher height and cutout. Additionally,
3/8˝ (10 mm) must be added to the dishwasher width and
cutout width.
23-5/8" – 24"
600 – 610 mm
24"
610 mm
4"
102 mm
5-3/8"
136 mm
**33-7/8" – 36" minimum
**860 – 914 mm
2"
51 mm
Page 5 Customer Care Center
1-800-898-1879
www.askousa.com
Height (Adjustable)* 32-1/4˝ to 34˝ 819 mm to 864 mm
Width 23-5/8˝ 600 mm
Depth (Includes high loop) 22-7/8˝ 581 mm
Depth W/Door Open 48-3/8˝ 1229 mm
Weight 108 Ib 49 kg
Electricity 120V, 60Hz, 15 amp
Water pressure 4.2 - 140 psi,
0.03-1.0 MPa,
0.3-10 Bar
Heating element 1200 watt
Max loading 1300 watt
*32-1/4" to 34"
*819 mm to 864 mm
5-3/8" to 7-3/8"
137 mm to 187 mm
2-7/8"
73 mm
3-3/8"
86 mm
9"
228 mm
48-3/8"
1229 mm
22-7/8"
581 mm
23-5/8"
600 mm
3-1/8"
79 mm
Door
The best place for your dishwasher is in the kitchen near
the sink. This makes it easier to connect the water and
drain supply lines.
A built-in dishwasher must be enclosed on the top, both
sides and the back.
The power-supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the
undercounter space in whitch the appliance is to be
installed.
The electrical and water supplies should enter through the
area indicated by the shading on the illustration at right.
Preferably, they should come through the right side of the
machine. The access hole must be round and smooth and
no bigger than 1-1/2˝ (38 mm) in diameter. If the partition
is metal, it needs to be covered with an edge protector.
Use caution when the appliance is installed or removed, to
reduce the likelihood of damage to the power-supply cord.
Height* 32-1/4˝ – 34˝ 819 – 864 mm
Width 23-5/8 – 24˝ 600 – 610 mm
Depth 24˝ 610 mm
* 32-1/4˝ (819 mm) height requires removal of top trim, and
lowering side trim (2).
23-5/8” – 24"
600 mm – 610 mm
24"
610 mm
4"
102 mm
5-3/8"
136 mm
*32-1/4" – 34" minimum
*819 – 864 mm
2"
51 mm
Page 6 Customer Care Center
1-800-898-1879
www.askousa.com
ASKO XLADAFI dishwashers can be installed either with or without accessory ll strips depending on the type of installation.
If the dishwasher cutout has been cut to European widths of 23-5/8˝ (600 mm), the unit won’t require ll strips. If the
dishwasher cutout is a standard 24˝ (610 mm) wide, we have ll strips that make the unit 24˝ (610 mm) wide.
The ASKO accessory ll kit for 23 5/8˝ (600 mm) Width
Door Panels (8077317-95), which includes the counter
saver ll strip and both side ll strips, should be installed
in the back mounting holes.
The ASKO accessory ll kit for 23-7/8˝ (606 mm) Width
Door Panels (8078982-95) which includes the counter
saver ll strip and both side ll strips, should be installed
in the front mounting holes.
Page 7 Customer Care Center
1-800-898-1879
www.askousa.com
1. Attach the light shielding film (packed in the
document bag) to the underside of the countertop
above the touch buttons. (Only certain models).
The light shielding lm ensures optimal button
functionality.
The surface on which the protective lm is to be
attached must be clean and dry.
1
2. Attach the supplied door sealing
(only certain models).
This strip is an essential part of the Turbo Dry
Express system and must be installed to ensure
an optimum seal between the dishwasher tank
and door.
1
2
2
3. Start by measuring the height from the oor to the
bottom edge of the counter top. Measure the height
from the oor to the top edge of the dishwasher.
4. Push the plastic feet into place on all steel feet
(included in document bag).
Do not attach the plastic feet if the installation space
is too tight.
3
5. Loosen the lock nuts on the dishwasher’s steel
feet using a 5/8 inch (16 mm) open-ended wrench.
Screw the lock nuts down as close to the oor as
possible.
5/8" (16 mm)
Page 8 Customer Care Center
1-800-898-1879
www.askousa.com
6. Adjust the height of the dishwasher by turning the
steel feet with your hands. Leave enough space to
adjust them later.
7. Screw in the back foot completely by turning the
adjustment screw at the front counterclockwise. Use
a at-bladed screwdriver or a 1/4˝ nut driver. (Only
models with front adjustable rear foot).
If the machine does not have a front adjustable rear
foot, level the remaining rear legs just as you did
the front legs.
8. Push the dishwasher into the cabinet. At the same
time, pull the power cord, the drain hose, and the
ll hose through the appropriate cut outs. Be careful
when pushing the dishwasher into place. The feet
could still damage certain types of ooring even with
the plastic foot covers in place.
If installing in a metal cabinet, the hole(s) for the
drain hose and connection pipe must be tted with
edge protectors/rubber grommets.
9. Lift the dishwasher a little at the front and turn the
front feet to lower them.
Page 9 Customer Care Center
1-800-898-1879
www.askousa.com
10. Check that the height of the machine corresponds
to the height from the oor to the bottom edge of
the counter top.
Do not attach the mounting screws. This will be
done later.
11. Adjust the back foot by turning the adjustment
screw at the front clockwise. (Only models with front
adjustable rear foot.)
If the machine does not have a front adjustable rear
foot, level the remaining rear legs just as you did
the front legs.
12. Place the spirit level on the dishwasher door to check
that the machine is level and adjust if necessary. The
door must be fully closed!
The dishwasher must be level!
An unlevel machine can aect the amount of water
taken in, the door can be dicult to close, and the
baskets dicult to place securely.
Page 10 Customer Care Center
1-800-898-1879
www.askousa.com
Follow the separate instructions supplied with the
dishwasher to attach the chosen accessory door or
custom panel to the front of the machine.
Once you have tted the accessory door or custom
panel to the dishwasher, the door springs may need
adjusting. Check that the door stays in the position in
which it is placed. If the door drops down when you
open it, the springs need to be tightened. If the door
shuts on its own, the springs need to be loosened.
See step 3 for further instructions.
The custom panel must not cover the air nozzle and
thereby block the ow of air.
Width 24˝ (610 mm) minimum to cabinet width minus
1/4˝ reveal
24˝ (610 mm) minimum to cabinet width minus
1/4˝ reveal
Height 28-1/8˝ (714 mm) for 6˝ toe kick to 30-1/8˝ (765
mm) for 4˝ toe kick
28-1/8˝ (714 mm) for 4˝ toe kick
Thickness 3/4˝ (19mm) 3/4˝ (19mm)
2x
1"
(25 mm)
2x
3/8"
(10 mm)
6x
1-1/2"
(38 mm)
2x
4x / 3x
1
4
5
7
6
2
3
This manual suits for next models
4
Table of contents
Other Asko Dishwasher manuals
Asko
Asko D5524 Assembly instructions
Asko
Asko D1716 User manual
Asko
Asko D5896XXLFI User manual
Asko
Asko DBI644MIB.W/1 User manual
Asko
Asko D5456SS User manual
Asko
Asko D3251HDSS User manual
Asko
Asko DFS244IBS User manual
Asko
Asko D5223 Configuration guide
Asko
Asko DFI664XXL.U User manual
Asko
Asko D1796 User manual
