Artiste ADH300 User manual
1
1. COMPONENT PART LIST
A)Transmitter
1.Power/Audio Signal Charging indicator
2.Charging pins
3.Audio IN Socket
4.DC IN Socket
2
B)Headphone Receiver
5.Volume Up and Down Control
6.Signal link LED indicator
7.Charging contacts
8.ON/OFF Control
9.Power LED indicator
C)Accessories
10.RCA-3.5mm cable
11.NiMH AAA size batteries for Headphone (2 pieces)
(Installed in headphone)
12.AC/DC adaptor
13.RCA - Female 3. 5mm cable
Retract Hear a click sound
Green Light Off CHARGING TIME:
5-7 hours
Charging contact
3
Charging
pins
2. CHARGING
1.For your convenience, rechargeable batteries have been inserted
in wireless headphones. Please charge it for 7 hours before first use.
2.Turn OFF the headset by pressing and holding the power button
about 2 seconds. Charge the transmitter, the red LED light start to
flash for around 6 seconds.
3.Retract the headphone band
to contact with charging pin
correctly
when charging.
4.Place the headphone on the charging cradle. Green LED will turn
on when it is charging correctly. Green LED will turn off after fully
charged.
Please retract the headphone
band to contact with charging
pin correctly when charging.
4
Headset will turn off automatically if there is no input of audio
signal or signal is too weak in 3 minutes, need to restart the headset
and play sound again.
Note: Rechargeable batteries have durable life. If you need to
replace them, the batteries are on the right earmuff. You just press
the latch down lightly, don't need much strength.Then insert 2 pcs
AAA rechargeable batteries supplied by ARTISTE into the compartment.
Make sure the batteries are placed at the right polarity.
Never attempt to charge other types of batteries or
non-recharge-
able
batteries.
AUTO OFF:
PHONE TEST
Jack Options
Natively
Supported？
Please refer
to Point: Hookup A Hookup B Hookup C N/A
AUX/3.5mm Optical Output Other RCA jacks
RCA(Red/White）
AUDIO OUT
3.
CHECK YOUR DEVICE’S OUTPUT PORTS
5
Before connect the transmitter to TV, it is better to connect to a
phone via 3.5mm cable to test the item. Connect the transmitter
to your phone via 3.5mm cable, then connect power to the
transmitter, turn on it, the LED light shows red. Play phone music,
turn on the headphone, LED light on the left turns to green,
indicating the headphone and the transmitter are connected
successfully; you will hear sound. (Refer Point 6.1 for detail)
4.1 Following Hookup: A
You need:
1. Headphone 2. Transmitter 3. RCA-3.5mm cable 4. AC/DC adapter
Using 3.5mm/AUX audio out
6
You need to use after hookup:
+
4. CONNECTION AND USE
3.5mm/AUX
AUDIO OUT
L
R
Note:
1.Please remember to turn the volume down before put them on, since the default
sound is high.
2.If you still can not receive audio on the headphone: connect the transmitter to
your Cable Box/Satellite Box rather than your television.
2.Turn on
Connect transmitter to power
and turn on headset
3.Green light on
Wait until the green light is on
the left earmuff , you will hear
sound
1.Play
Turn on TV and play sound
If no sound,please check the TV setting,refer to “5.TV SETTING”
Using RCA audio out (Red/White ports labeled AUDIO OUT)
7
4.2 Following Hookup: B
You need:
1.
Headphone
2.
Transmitter
3.
RCA-Female 3.5mm cable
4.
RCA-3.5mm cable
5.
AC/DC adapter
You need to use after hookup:
L
R
AUDIO OUT
L
R
Note:
1.Please remember to turn the volume down before put them on, since the default
sound is high.
2.If you still can not receive audio on the headphones while at the same time
hearing
audio from the television speakers: connect the transmitter to your
Cable Box/Satel
lite Box RCA audio out rather than your television.
If no sound,please check the TV setting,refer to “5.TV SETTING”
+
2.Turn on
Connect transmitter to power
and turn on headset
3.Green light on
Wait until the green light is on
the left earmuff , you will hear
sound
1.Play
Turn on TV and play sound
Using Optical audio out
8
4.3 Following Hookup: C
You need:
1. Headphone 2. Transmitter 3. RCA-Female 3.5mm cable 4.RCA-3.5mm cable
5. AC/DC adapter 6. Optical cable
(Need to purchase 6/7/8 separately)
Package doesn’t include the optical adapter
OPTICAL
DIGITAL
AUDIO OUT
L
R
Optical
Adapter
Input
Ouput
Input
Ouput
8.
AC/DC charger for the adapter
7. Optical adapter
⑥
⑧
④
③
⑤
9
You need to use after hookup:
Note:
1.Please remember to turn the volume down before put them on, since the default
sound is high.
2.If you still can not receive audio on the headphones while at the same time hearing
audio from the television speakers: connect the transmitter to your Cable
Box/Satel
lite Box RCA audio out rather than your television.
3.Please plug cables into port completely and correctly, If the plug is only half
inserted or not completely, there maybe noise.
If no sound,please check the TV setting,refer to “5.TV SETTING”
+
2.Turn on
Connect transmitter to power
and turn on headset
3.Green light on
Wait until the green light is on
the left earmuff , you will hear
sound
1.Play
Turn on TV and play sound
Table of contents
Other Artiste Headset manuals
