Aqua-Marina BLUEDRIVE S POWER FIN User manual
User’s Guide
WARNING
For your own safety and that of your equipment, make sure to take the following precautions. Failure to
follow warning notices and instruction may result in property damage, serious injury or death. Please
keep the manual and read it carefully before using the product; If the manual is lost, please contact our
after-sale service center.
aquamarina.com
PF-240S
BLUEDRIVE S POWER FINTM
EN
2
TABLE OF CONTENTS
I. SAFETY WARNING
II. MAIN COMPONENTS, PARAMETERS AND OVERALL DIMENSIONS
III. PACKING LIST
IV. INSTALLATION AND INSTRUCTION
V. MAINTENANCE
VI. GUIDANCE ON PROBLEMS
VII. WARRANTY AND AFTER SERVICE CONTACT INFORMATION
3
1. This product is only for providing power for water leisure products and only limited
to be used in water. It is forbidden to use it for other purposes.
2. When using the product, a proper emergency stop leash should be used.
3. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
4. Do not modify the product or add other parts to it in any way. If any parts is
damaged, please contact after-sale service center.
5. Wash the power fin and its motor with fresh water; and do not put it in sea water or
salt water to avoid damage to the motor.
6. This product is with li-ion batteries, always follow the batteries use principle and
matters needing attention.
7. The battery must be removed from the appliance before it is scrapped.
8. The appliance must be disconnected from the supply mains before removing the
battery.
9. The battery must be disposed properly according to local regulations.
10. Never charge or use the product in thunderstorms and lightning conditions.
11. It is necessary to check whether each connection is firm before each use.
12. Check whether its electricity is enough before each use.
13. The power fin only be supplied at SELV(Safety Extra Low Voltage), can be applied
only with specified batteries, specified chargers and remote control. If user needs
to replace them, please contact the appointed after-sale service center.
14. The electric charging port of the battery case should be either connected with the
power fin, or connected with charger, or cover its lid to avoid short circuit damage
caused by other metals or moisture.
15. When the remote control and the charger are not used for a long time, it is
necessary to disconnect power supply.
16. When it is not in use, it should be stored under the temperature of -15°~45° and
avoid direct sunlight.
17. If the power fin is scrapped or need to be replaced with new one, it is necessary to
follow the principle of recycling or return it to the dealer.
18. The appliance can be only used with specified chargers from the original
manufacturer.
19. The components with electric box and motor is for the field installed equipment, its
installation to ISUP shall be considered the safety requirements of moving part,
water proof and other risks.
SAFETY WARNING
4
FCCID: 2AVFRPF-240S
FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
• If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
CAUTION: Any changes or modifications not expressly approved by the grantee of this
device could void the user's authority to operate the equipment.
RF EXPOSURE WARNING
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
The equipment must not be co-located or operating in conjunction with any other antenna or
transmitter.
5
POWER FIN PRODUCT DETAIL:
Metal connector
Motor
propeller
Motor
Motor protective
cover
Motor
protective
cover
Guide vane
6
PARAMETERS
Underwater Jet
Battery Case
Charger
Operating Speed: 4-6km/h
• Low gear : Max. Speed 4km/h
• High gear : Max. Speed 6km/h
Runtime: 1h for low gear, 0.5h for high gear
Protective Cover Material: ABS
Dimension: 300 x 210 x 110mm (11.8” x 8.3” x 4.3”)
Weight: 2.5kg (5.5lbs)
Rechargeable Battery Pack: 11.1VDC, 8.8Ah/97.68Wh
Special lithium-ion battery for BlueDrive S Power Fin
Material: flame retardant ABS
Battery Life: ≥300 cycles
Dimension: 210 x 155 x 75mm (8.3” x 6.1” x 3”)
Net Weight: 1.25kg (2.8lbs)
With rechargeable battery, circuit board and
2-in-1 magnetic switch (working as both power
switch and emergency stop switch)
Input: 100-240VAC, 50/60Hz, 1.6A
Output: DC12.6V 5A
E480809
Full charging time for battery pack is 2~3 hours
Packing Dimension: 62 x 29.5 x 18.5cm (24.4'' x 11.6'' x 7.3'')
Packing weight /
Net weight:
5.9 kg (13 lbs) /
4.25 kg (9.4 lbs)
Interface: Metal interface of marine waterproof for plug in
7
OVERALL DIMENSIONS:
210mm
300mm
Overall dimension chart of power fin, 300 x 210x 110mm (11.8" x 8.3" x 4.3")
Overall dimension chart of the battery case,
210 x 155 x 75mm (8.3" x 6.1" x 3")
Overall dimension chart of the handbag,
610 x 282 x 175mm (24" x 11.1" x 6.9")
155mm
282mm
210mm 610mm 175mm
110mm
8
PACKING LIST
No. Name of component
part Picture Quantity/
Unit Remark
Underwater Jet With power cord, plug,
fin base and push-in pin
1 1 Set
Battery Case ( Include
Li-ion battery pack)
2 1 Set
Elastic rope buckle3 1 Set
Remote Control4 1 Set
Charger5 1 Set
Manual American standard6 1 Copy
With rechargeable
battery, circuit board
and 2-in-1 magnetic
switch (working as
both power switch and
emergency stop
switch)
Black elastic rope of
88cm in length with
carabiner
With arm band, remote
control and battery
(CR 2025/CR 2032 3V)
Picture shown
9
INSTALLATION AND INSTRUCTION
1. Open the packing box and check whether the components are complete
2. Install power fin (As shown in the picture)
2.1 Insert the bottom of power fin into the fin base;
2.2 Insert the slide in push-in pin into the fin base;
* With a US Fin adaptor, the power fin can be also used on any watercrafts with a US FIN
box.
2.1
a b c
d
2.2
Insert push-in pin
Insert push-in pin
3. Install the battery case
Firstly check whether the battery case is with electricity (please refer to the manual of
Magnetic Switch for details). If it is without or lack of electricity, please charge the battery
case in following steps. (As shown in following pictures)
Plug in
four core
10
a. Insert the power cord of the charger into the corresponding hole position on the charger to
charge the battery case.
b. Screw off the metal nut on the back of the battery case counterclockwise;
c. Connect the metal plug on the charger to the corresponding connector on the battery case
(Please note the direction of convex and concave corresponding position) and tighten the nut;
d. Plug the power plug of the charger into the home power supply.
e. Snap the magnetic switch in the right position of the battery case. And the indicator light on
the charger will turn red when it is charging successfully. Please note: the battery case can
NOT be charged when it is not connected with the magnetic switch.
f. The indicator light on the charger will turn solid green when the battery case is fully charged.
After charging, remove the power plug and charger and keep them properly for next
charging.
3.1 Put the battery case on the product with the
direction of metal plug towards the stern;
3.2 Fix the battery by fastening the elastic ropes
across the bottom of board respectively
and hook them on the 4 corners of battery box.
Metal plug towards the stern
4. The connection between the power fin and the battery case: screw off the nut lid of the metal
plug on the battery case, and insert the metal plug in the end of power line of the power fin
into the corresponding metal socket hole of the battery case with correct direction and proper
inserting; and tighten the metal nut;
This manual suits for next models
2
Table of contents
Languages:
Other Aqua-Marina Engine manuals
