Aqara E1 User manual
Curtain Driver E1 Rod Version User Manual
Мотор раздвижных штор E1 (для штанги):
Руководство по эксплуатации
Bedienungsanleitung für Vorhangsmotor E1 (Stabversion)
Moteur Rideau E1 (Version de la tige) Manuel d’utilisation
Dispositivo di Azionamento per Tende E1 (versione a stelo)
Manuale di Istruzioni
Manual de instrucciones para Controlador de cortina
inteligente E1 versión de varilla
カーテンドライバE1(ロッドタイプ) 取扱説明書
커튼 드라이버 E1 Rod Version 사용자 매뉴얼
窗簾驅動器羅馬桿版 使用說明書
01.
16.
30.
45.
60.
75.
90.
102.
104.
Warnings
1.WARNING: Important safety instructions. Follow all instructions since
incorrect installation can lead to severe injury. It is important for the
safety of persons to follow these instructions. Save these instructions.
2.WARNING: the driver should be disconnected from its power source
during cleaning, maintenance, and when replacing parts.
3.Frequently examine the installation for imbalance and signs of wear or
damage to cables springs and fixings. Do not use if repair or adjustment
is necessary.
4.Repairs must be performed by authorized personnel only or you will
void your warranty.
5.Do not operate when maintenance, such as window cleaning, is being
01
Indicator
Setting button
USB Type-C port
Hook
Wheel
Light sensor
Click once: to open, close or stop the
curtain;
Click twice in succession：to
release, withdraw or stop the hook;
Click three times in succession: to
manually set the start or end
position of the curtain;
Touch & hold for 5 seconds: to turn
on the device or reset to factory
settings;
Touch & hold for 10 seconds: to turn
o the device.
Product Introduction
Curtain Driver E1 is a motorized device that can control your existing
curtains automatically, it is based on the Zigbee 3.0 wireless protocol and
can achieve scheduled control of curtains, and work with other smart
devices when connected to the Aqara Home app.
*An Aqara Zigbee 3.0 hub is required. Some functions require specific models of hubs.
Please consult www.aqara.com/support for more details.
Please scan the QR code below to view the installation and operation
guide video. If the video is unable to be reached, you can also install the
product according to the method described in the manual.
02
What's in the Box
Tutorial Video
USB-C to USB-A
Cable × 1
Clip × 8 Rod Accessory × 1Rubber Strip (3m)×1
carried out in the vicinity.
6. Fixed controls must be clearly visible aer installation.
7. Before installing the drive, remove any unnecessary cords or
components and disable any equipment not needed for powered
operation.
8. That the characteristics of the driven part must be compatible with the
rated load and rated operating time.
9. This appliance contains batteries that are non-replaceable.
10.This appliance should not be used by children aged 8 years and under
and persons with reduced physical, sensory or mental capabilities.
11.Children should not play with the appliance.
12.Cleaning and user maintenance should not be done by children.
13.Do not allow children to play with fixed controls.
Installation Requirements
Curtain description
Grommet Curtains Ring Top Curtains
If you are using grommet curtains, the minimum spacing between two
grommets should be greater than 95mm.
If you are using ring top curtains, the thickness of the rings should be
greater than 4mm.
Rod diameter requirement: 25-32mm (corresponding to circumferences
of 79-100mm)
03
＞95mm
Grommet Grommet
＞4mm
diameter：25-32mm
Note: This product is only applicable to rods with uniform thickness, not
to those with dierent thicknesses at the ends, such as telescopic rods.
04
1.This product needs to be connected with the Aqara Home app before
being installed on the curtains.
2.Before activating the product, please make sure you have the Aqara
Home app and the Aqara Zigbee 3.0 hub installed (Please scan the QR
code below to download the app).
3.Please open the app, tap “Home” and then tap “+” in the top right
corner to enter the “Add Device (Accessory)” page. Select “Curtain
Driver E1” and the hub to be connected to, and add it according to
instructions in the Aqara Home app. Press and hold the Setting button
for 5 seconds, and wait for the voice prompt from the Hub.
4.If you have purchased two or more Curtain Drivers, please connect all of
them to the Aqara Home app before further installation.
5.If you use double-sided curtains, it is necessary to connect two Curtain
Drivers to the app and then put them in one group for simultaneous
control. Enter the main page of the Curtain Driver to be grouped, click
"... " in the upper right corner, select ”Create a group for Curtains” and
follow the instructions.
6.It is recommended to fully charge the product before installation.
7.The mass and the dimension of the curtain to be driven shall be compati-
ble with the rated torque and rated operating time.
Please read the following steps to start using the product.
Preparation before use
Quick Start Guide
The Rods shall be provided with
close-fitting decorative caps.
05
Installation Methods for Rods
Single-Sided Curtains (only one Curtain Driver is needed)
1.Force apart the standard Rod hanger, hang it between the first and
second rings (or grommets) on the movable side of the curtain, and
tighten the four legs of the hanger;
2.Aer startup, quickly double tap "Setting button" to release the hook on
the curtain driver until it reaches its maximum length, and completely
close the curtain;
3.Hang the curtain driver on the hanger as shown in the figure below,
quickly double tap "Setting button" to hold the curtain driver onto the
rod. Then, the indicator will turn green and blink, and 3 short beeps will
sound from the buzzer when the product it is held in place.
Installation Methods
Hold the sides of the hanger
to lightly force it apart；
Pinch the ring hole until
a "click" is heard；
The hook reaches out to
the maximum length;
The hook is locked to
the innermost;
The second
ring
Opening direction of curtains
The first ring
This product can be configured on the app to open and close the curtains
according to the intensity of ambient light. To use the function, the light
sensor should face the outside of the window and the Curtain Driver
should be installed on the side near the window. If you need to control
the opening and closing of curtains according to the light indoor, the light
sensor should face the interior and the Curtain Driver should be installed
on the side near the interior. To optimize the eect of the light sensor,
please ensure that there is no opaque object in front of it.
06
1. First, measure the number of holes "N" between the outer edges of two
adjacent Grommets with the rubber strip as shown in the figure below
(measure the shortest straight-line distance between the outer edges of
the Grommets);
2. Install the first clip onto the third hole from the le of the rubber strip,
and install all the other clips according to the following instructions.
Reserve 5 holes between the second and first clips, and the number of
holes between the other adjacent clips is "N×2" (including the hole
occupied by the clip)
Install clips and rubber strip (for curtains suitable for
Grommets)
罗马圈
罗马圈
1 2 3 ... N
1 2 31 2 3
Turn the rubber strip up
to place it in the groove.
Grommets Grommets
Other manuals for E1
7
Table of contents
Languages:
Other Aqara Home Automation manuals
Aqara
Aqara Hub M1S Gen User manual
Aqara
Aqara E1 User manual
Aqara
Aqara Hub M2 User manual
Aqara
Aqara M1S User manual
Aqara
Aqara Cube T1 Pro User manual
Aqara
Aqara Hub E1 User manual
Aqara
Aqara Zigbee Installation guide
Aqara
Aqara ZHWG11LM Dimensions and installation guide
Aqara
Aqara E1 User manual
Aqara
Aqara SSM-U02 User manual
