Apera Instruments 2301-C User manual

2310-C High-Range Conductivity Electrode

User Manual

Brief Introduction

Apera Instruments 2310-C High-Range Conductivity Electrode is featured with a proprietary platinum

black ring sensor for accurate readings in an ultra-wide conductivity range up to 2000 mS/cm.

Technical Specifications

Range

20 to 2000 mS/cm

Housing

POM

Constant

K=10

Connector

BNC

Cable length

3 Ft

Dimension

ø12*145 mm

Temperature sensor

N/A

Operating temperature

32 to 176°F (0 - 80°C)

How to Install the Electrode

1. Find the conductivity BNC socket (where it shows Cond) on the conductivity meter; Open the

rubber cap; Insert the BNC connector of the electrode to the BNC socket while twisting clockwise

until it’s locked.

2. After connecting the new electrode to your meter, adjust the meter’s constant K to 10 according

to the instruction of your meter’s manual. Then perform a 2 to 3-point calibration to ensure the

accuracy.

How to Use the Electrode

1. There is a proper amount of deionized water in the cap on top of the electrode. The conductivity

sensor is soaked in it to keep its sensitivity.

2. Before measuring, loosen the bottle cap, then pull out the electrode while twisting

counterclockwise. Place the storage bottle at a safe position.

3. Rinse the electrode with distilled or deionized water and blot-dry it with clean tissue or filter paper.

Rinse the electrode again with your test solution if possible for the best result. Never rub the

sensor.

4. Insert the electrode into your sample solution and stir it for a few seconds in the solution to

remove potential air bubbles. Then wait for the stable reading and take the measurement.

5. After measurement, insert the electrode back into the storage cap and twist it on. If the water in

the cap is contaminated, rinse out the storage cap and fill in new deionized or distilled water.

How to Maintain the Electrode

1. Always rinse the electrode with distilled or deionized water before and after each test and

calibration.

2. Store the electrode in the storage cap filled with distilled or deionized water when not in use.

3. Keep the electrode connector clean and dry. Use cotton balls with isopropyl alcohol to clean if it

gets dirty and then blow-dry it. This is to prevent a potential short circuit, which will undermine the

electrode’s performance.

Limited Warranty

We warrant this electrode to be free from defects in material and workmanship and agree to repair or

replace free of charge, at the option of APERA INSTRUMENTS, any malfunctioned or damaged

product attributable to responsibility of APERA INSTRUMENTS for a period of SIX MONTHS from the

delivery.

This warranty does not cover any damages due to:

Accidental damage, transportation, storage, improper use, failure to follow the product instructions,

unauthorized repair, normal wear and tear, or any other actions or events beyond our reasonable

control.

APERA INSTRUMENTS (Europe) GmbH | Wilhelm-Muthmann-Str.18, 42329 Wuppertal, Germany

info@aperainst.de | www.aperainst.de | Tel.: +49 202 51988998

Table of contents

Other Apera Instruments Test Equipment manuals

Apera Instruments

Apera Instruments COND5 User manual

Apera Instruments

Apera Instruments EC60 User manual

Apera Instruments

Apera Instruments LabSen 751 User manual

Apera Instruments

Apera Instruments GroStar GS4 User manual

Apera Instruments

Apera Instruments EC20 User manual

Apera Instruments

Apera Instruments TDS20 User manual

Apera Instruments

Apera Instruments ORP60-Z User manual

Apera Instruments

Apera Instruments Premium Series User manual

Apera Instruments

Apera Instruments PC60 User manual

Apera Instruments

Apera Instruments LabSen 841 User manual

Apera Instruments

Apera Instruments PH60F-E User manual

Apera Instruments

Apera Instruments 201T-F User manual

Apera Instruments

Apera Instruments TDS1 User manual

Apera Instruments

Apera Instruments PH60 User manual

Apera Instruments

Apera Instruments ORP60 User manual

Apera Instruments

Apera Instruments ZenTest PC60-Z User manual

Apera Instruments

Apera Instruments ZenTest PH60S-Z User manual

Apera Instruments

Apera Instruments EC20 User manual

Apera Instruments

Apera Instruments Premium Series User manual

Apera Instruments

Apera Instruments 28APE190027 User manual

Apera Instruments

Apera Instruments PH60 User manual

Apera Instruments

Apera Instruments PH20 User manual

Apera Instruments

Apera Instruments PH60 User manual

Apera Instruments

Apera Instruments GroStar GS3 Premium User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Agilent Technologies

Agilent Technologies BERT Serial Getting started

Agilent Technologies

Agilent Technologies N3280A user guide

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual