APART concept1t User manual
CONCEPT1(T)
Instruction manual
Instruction manualCONCEPT1(T)
3
CONCEPT1(T) Manual
4
Integrated amplifiers
Safety Instructions
• Please check the carton box for any kind of damage on
reception of the goods. In case of a damaged carton, please
contact your dealer before opening the carton.
• !!!! Danger !!!! Exposure to extremely high noise levels may
cause a permanent hearing loss. Individuals vary considerably to
noise induced hearing loss but nearly everyone will lose some
hearing if exposed to sufficiently intense noise for a sufficient
amount of time. Therefore it is recommended that all persons
exposed to equipment capable of producing high sound
pressure levels, such as this amplifier, be protected by hearing
protection while installing or operating this unit.
• Read all documentation before operating your equipment.
• Keep all documentation for future reference.
• Save the carton and packing material even if the equipment has
arrived in good condition.
• Should you ever need to ship the unit, use only the original
factory packing.
• Do not spill water or other liquids into or on the unit.
• Make sure power outlets conform to the power requirements
listed on the back of the unit.
• Do not use the unit if the electrical power cord is frayed or
broken.
• Have gain controls on amplifiers turned down during power-up
to prevent speaker damage if there are high signal levels at the
inputs.
Instruction manualCONCEPT1(T)
5
• Do not connect the inputs / outputs of amplifiers or consoles
to any other voltage source, such as a battery, mains source, or
power supply, regardless of whether the amplifier or console is
turned on or off.
• Power down & disconnect units from mains voltage before
making connections.
• Do not use the unit near stoves, heat registers, radiators, or
other heat producing devices.
• Do not operate equipment on a surface or in an environment
which may distort the normal flow of air around the unit. If the
unit is used in an extremely dusty or smoky environment, the
unit should be periodically “blown free” of dust.
• Do not remove the cover. Removing the cover will expose you
to potentially dangerous voltages.Do not drive the inputs with
a signal level higher than that required to drive equipment to
full output.
• Do not run the output of any amplifier back into another input.
• In case of mal-function this device should be serviced by
qualified service personnel only.
6
Integrated amplifiers
Main features
• 3 basic operating modes combined in 1 device: stereo, linked
mono and individual mono.
• Paging microphone input with 2 zone programmable paging
control.
• Standalone and/or RS232 controlled operation.
• Removable 19 inch rack ears.
• Menu driven hidden configuration accessible for installers only.
• Lockable front panel controls.
• Super simple no nonsense user interface.
• Multi functional stylish blue colour dot matrix VFD display.
• Presettable paging mic gain and separate tone control.
• Integrated switchable highpass filter for use with optional
subwoofers.
• Separate line out and pre out (fixed and variable line outs).
• 4 stereo gain adjustable line inputs with additional link out on
input 1.
• Line 4 input also available as a standard minijack in on the
frontpanel for connection of personal audio devices.
• Programmable maximum microphone and music levels for all
zones.
• Switchable automatic loudness compensation.
• 2 zone paging microphone optionally available.
Instruction manualCONCEPT1(T)
7
• Low impedance (Concept 1) and 100 volt speaker line outputs
(Concept 1T) available.
• Integrated limiter circuit.
• IR remote control optionally available.
• IR control extender optionally available.
• 2 x 60 watts freely assignable RMS output power at your
disposal.
8
Integrated amplifiers
Front panel and display layout
1. Power on/off button: push this button to turn the power on
and off
2. Source A selector: push this button to select line source A
3. Source B selector: push this button to select line source B
4. Source C selector: push this button to select line source C
5. Source D selector: push this button to select line source D
6. Source D minijack input: this line input is shared with the source
D connector at the rear
7. Select button: push this button to select basic submenus
8. Multifunctional encoder knob: turn this knob to adjust the main
volume and other menu parameters
9. Stand-by led: this led is lit when the unit is powered off by
RS232 control
1 2
3
4
5
6 7 8
9
1110
Instruction manualCONCEPT1(T)
9
10. Infrared receiver
11. Multi functional dot matrix VFD display
10
Integrated amplifiers
Rear panel layout
1. Microphone input: connect your (paging) microphone on this
euroblock connector, connect the signal on +, -, the screen on
GND. Connect the eventual paging contacts between GND and
Z1 (for zone 1) and between GND and/or Z2 (for zone 2). The
input gain can be adjusted with knob 2 between line and mic
level to avoid distortion.
2. Mic input gain control: mic input gain adjust
3. Mic input tone control: adjust the tone of the mic input
between dark and bright
4. Ground connection: connect your safety ground lead or screens
of your shielded input cables on this screw if necessary.
5. Link output: the signal here is a copy of the line A input signal
6. Line A: stereo line RCA connector
7. Line B: stereo line RCA connector
8. Line C: stereo line RCA connector
1 2 3 5
4
6 8
7 9 1611
10
12 1413 15 17 18
Table of contents
Other APART Amplifier manuals
APART
APART Champ - 4 User manual
APART
APART MA200 User manual
APART
APART AUDIOSYSTEM8.8 User manual
APART
APART MA-35 User manual
APART
APART MA240 User manual
APART
APART MA125 User manual
APART
APART SBR-160 User manual
APART
APART REVAMP2120T User manual
APART
APART PM1122 User manual
APART
APART PA4060 User manual
APART
APART Champ-2 User manual
APART
APART MA200CDR User manual
APART
APART PM7400 MKII User manual
APART
APART pubdrive2000 User manual
APART
APART MA-65 User manual
APART
APART ZONE4 User manual
APART
APART REVAMP4240T User manual
APART
APART PA2240BP User manual
APART
APART PA-CONF-E User manual
APART
APART CONCEPT1 User manual
