APART vinci 2125 User manual
VINCI 2125
Instruction manual
Installed Sound Solutions
Vinci 2125
Instruction manualVINCI 2125 3
Safety instructions
tPlease check the packing for any kind of damage upon
reception of the goods. If the packing is damaged, please
contact your dealer before opening it.
t!!!!DANGER!!!! Exposure to high sound pressure levels
may cause permanent hearing loss. Hearing loss induced by
exposure to high sound pressure levels will vary from individual
to individual, but nearly everyone will lose some hearing
when exposed for a sufficient amount of time. Therefore, it is
recommended that all persons exposed to equipment capable
of producing high sound pressure levels, such as this amplifier,
wear sufficient ear protection while installing or operating this
unit.
tRead all documentation before operating your equipment.
tKeep all documentation for future reference.
tKeep the carton and packing material, even if the equipment
has arrived in good condition.
tShould you ever need to send the unit back, please only use the
original factory packing.
tDo not spill water or other liquids on or into the unit.
tMake sure power outlets are conform to the power
requirements listed on the back of the unit.
tDo not use the unit if the electrical power cord is damaged.
tAlways operate the unit with the AC ground wire connected to
the electrical system ground.
4Limited Edition Amplifier
tTurn the level controls on the amplifiers all the way down
during power-up to prevent speaker damage if there are high
signal levels at the inputs.
tDo not connect the inputs / outputs of amplifiers or consoles
to any other voltage source, such as batteries, mains sources or
power supplies, regardless of whether the amplifier or console
is turned ON or OFF.
tPower down and disconnect units from mains voltage before
making connections.
tDo not use the unit near stoves, heat registers, radiators, or
other heat producing devices.
tDo not operate equipment on a surface or in an environment
which may distort the normal flow of air around the unit. If the
unit is used in an extremely dusty or smoky environment, the
unit should regularly be “blown free” of dust.
tDo not remove the cover. Removing the cover will expose you
to potentially dangerous voltages.
tDo not drive the inputs with a signal level higher than that
which is required to drive equipment to full output.
tDo not run the output of any amplifier back into another input.
tIn case of malfunction, this device should be serviced by
qualified service personnel only.
Instruction manualVINCI 2125 5
Introduction
Congratulations on your 20th Anniversary Limited Edition Amplifier
purchase. We have done the best we can to assure you pristine
audio quality at the best possible price. By combining analog
amplifier technologies with state of the art 24 bits/192 kHz digital
to analog converters, we have created a stylish high fidelity music
control center in a slim package.
A few headlines: CS8416 digital audio interface receiver and
AD1955 multibit delta sigma decoder chips, OPA2134 operational
amplifiers, CS3310 volume control chip… All high quality
components usually found in high-end gear from exclusive
manufacturers.
With 3 analog input pairs, a high-end phono preamp for MM or
MC pick-up elements and 4 digital inputs, VINCI 2125 will be your
reference amplifier for many years to come.
6Limited Edition Amplifier
Operation
1. Power switch: push the switch to power the unit on or off.
2. Infrared control receiver: do not cover this area.
3. VFD display: shows the selected input (e.g. “CD”) and actual
volume setting (e.g. “-12dB”).
4. Volume & Menu knob: in normal mode, turn to the right to
increase the volume, turn to the left to decrease. Push briefly to
switch to the next input: CD, DVD, AUX, PHONO, CO1, CO2,
CO3, OPT. The volume range is from -30dB to +41dB. The
amplifier will memorize the last volume setting if the volume
is lower than +20dB. If the last volume setting is above +20dB
before power off, the amplifier will be set automatically to +20
dB at next power on. If the last setting is below +20dB, the
amplifier will be set to the last known volume level.
1 2 3 4
Instruction manualVINCI 2125 7
Error message on the display: if “PROTECT” appears on the display,
the amplifier will mute the outputs and no sound will be heard. This
can have following reasons:
t5IFMPBEJNQFEBODFJTMPXFSUIBOPINTSFTVMUJOHJOFYDFTTJWFpower requirements.
t5IFSFJTBTIPSUDJSDVJUBUUIFPVUQVUUIFTQFBLFSMJOFPSUIFspeaker itself is short circuited.
t5IFSFJTBGPSFJHOWPMUBHFQSFTFOUPOUIFTQFBLFSMJOFTt5IFBNQMJmFSJTPWFSIFBUFEPower off the amplifier, remove all speaker wires and inputs and
remove the error condition. If the amplifier is overheated, allow it to
cool down first.
If the error persists, consult your dealer for further assistance.
8Limited Edition Amplifier
3
1. Right channel speaker: connector positive and negative
terminal. Do not short circuit these terminals!
2. Phono input: left and right analog input on RCA connectors.
3. Phono ground: connector and mode switch: set to MM for
moving magnet pick-up elements, set to MC for moving coil
pick-up elements.
4. CD analog input: left and right input on RCA connectors.
5. DVD analog input: left and right input on RCA connectors.
6. AUX analog input: left and right input on RCA connectors.
7. CO1 digital input: coaxial SPDIF digital input on RCA
connectors.
8. CO2 digital input: coaxial SPDIF digital input on RCA
connectors.
9. CO3 digital input: coaxial SPDIF digital input on RCA
connectors.
5 6 7 9 11
12 4 8 10 12
Instruction manualVINCI 2125 9
10. OPT optical input: input on Toslink® connector
11. Power socket: with integrated mains fuse. Please replace only
by a fuse with the same voltage and current rating. If the fuse
blows regularly, consult your local dealer.
12. Left channel speaker: connector positive and negative terminal.
Do not short circuit these terminals!
Use of the infrared remote control unit is
straight forward: press PHONO, CD, DVD,
AUX, CO1, CO2, CO3 or OPT to select one of
the analog or digital inputs.
Press VOLUME+ to increase the volume level,
press VOLUME- to decrease the level.
Press MUTE to mute the outputs. Press MUTE
once more to unmute the outputs.
Press DIM to dim the brightness of the VFD
display in 5 steps.
10 Limited Edition Amplifier
Technical specifications
Information on handling batteries / rechargeable batteries.
Please adhere to the following information when handling batteries
and rechargeable batteries:
t,FFQCBUUFSJFTPVUPGDIJMESFOTSFBDIt#BUUFSJFTBSFIB[BSEPVTXBTUFBOEEPOPUCFMPOHJOIPVTFIPMEwaste.
t&OTVSFDPSSFDUQPMBSJUZXIFOJOTFSUJOHCBUUFSJFTt"MXBZTSFNPWFCBUUFSJFTXIFOUIFSFNPUFDPOUSPMJTOPUJOVTFGPSlonger periods of time.
Output power per channel 80 watts @ 8Ω
125 watts @ 4Ω (RMS, THD<1%)
Load impedance 4-8Ω (recommended)
THD <0.038% (8Ω load @ 1W/1KHz)
Signal to noise ratio >96 dB (A-weighted)
Frequency response 10Hz-60KHz (+1/-3dB)
Line input impedance 10KΩ
Line input sensitivity 250 mV
Other manuals for vinci 2125
1
Table of contents
Other APART Amplifier manuals
APART
APART MA247 series User manual
APART
APART MA200 User manual
APART
APART AUDIOSYSTEM8.8 User manual
APART
APART Champ-2 User manual
APART
APART REVAMP1680 User manual
APART
APART PA2240BP User manual
APART
APART MA-35 User manual
APART
APART MA246 User manual
APART
APART REVAMP1120T User manual
APART
APART MA30 User manual
APART
APART MA200 User manual
APART
APART MA-65 User manual
APART
APART Champ-One User manual
APART
APART ZONE4 User manual
APART
APART REVAMP4120T User manual
APART
APART REVAMP2600 User manual
APART
APART REVAMP4240T User manual
APART
APART SB-160 User manual
APART
APART MA240 User manual
APART
APART REVAMP2060T User manual
