AODELAN E3+ User manual
1
Wireless Flash Trigger Receiver
无线电引闪接收器
2
1
Thank you for purchasing Aodelan product.
Note: Before using the E3+Wireless Trigger for Canon, please read this
instruction manual carefully. Please also note to upgrade its rmware to the
latest version following the instructions provided on www.aodelan.net. (To
check the rmware version, please see page 9).
Warnings
1. This product is a precise electronic instrument. Do not expose to damp
environments or dust.
2. Please shut down the power of all devices when installing the wireless
trigger.
3. Do not drop or crush.
4. Do not use the wireless trigger at ammable, explosive or high temperature
environment.
5. Do not use harsh chemicals or solvents to clean the body. Use a soft cloth
or lens paper.
6. Remove batteries from the wireless trigger if not being used for an extended
period.
7. Interference: The E3+ wireless trigger transmits radio signals at 2.4GHz.
Its performance can be affected by electrical current, magnetic elds, radio
signals, wireless routers, cellular phones, and other electronic devices.
Environmental objects, such as large buildings or walls, trees, fences, or cars
can also affect transmission performance. If your wireless trigger can’t be
triggered, move its location slightly.
2
FCC Interference Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the
followingtwo conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This device and its antenna must not be co-
located or operating in conjunction with any other antenna or transmitter.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
3
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
E3+ Wireless Trigger For Canon/Receiver
E3+ receiver is a receiver for wireless ash shooting, used to work with non-
wireless Canon ETTL Speedlites and thus to perform wireless radio receiving
function. The receiver is compatible with multiple wireless radio transmitting
devices, including Aodelan E3+ transmitter, Canon ST-E3-RT Speedlite
transmitter, and Canon Speedlites that are compatible with radio transmission
wireless shooting.
4
Table of Contents
I. Parts --------------------------------------------------------------------------------------------5
II. Preparation Before Use -----------------------------------------------------------------6
III. The LCD Display-------------------------------------------------------------------------11
IV. Wireless Flash Shooting: Radio Transmission-------------------------------12
V. Trouble Shooting Guide---------------------------------------------------------------17
5
1
2
3
4 5 6 7
8
9
I.Parts
1. Radio transmission
conrmation lamp
2. LCD panel
3. Power button
4. Function button 1
5. Function button 2
6. Function button 3
7. Function button 4
8. Test ash button
9. Hot shoe mount
10. Batter compartment
11. Cold shoe/Tripod lug
12. Locking ring
13. 5V DC power port
14. 3.5mm output port
15. USB port
11
10
12
13
14
15
6
II.
Preparation Before Use
Installing the Batteries
1. Press the battery compartment
cover and slide it down as shown to
open the battery cover.
2. Insert the batteries. Make sure the
“+” and“-”battery contacts are correctly
oriented as shown. (Note: Please use
2 pieces of AA alkaline batteries or AA
type NI-MH batteries.
3. Replace the battery cover and push
back into the locked position.
4. When the power icon on the LCD
screen displays insufcient power,
replace the batteries with new ones.
_
+
7
Attaching and Detaching
the E3+Receiver
Attaching the ash to the E3+
Receiver
1. Align the ash’s hot shoe and the
E3+ receiver’s hot shoe mount.
2. Slide the ash all the way into the
E3+ receiver’s hot shoe mount
3. Lock the ash with the ash’s
locking mechanism.
Detaching the ash
1. Release the lock of ash
according to its locking mechanism
(see picture).
2. Slide the ash out of E3+
receiver’s hot shoe mount. 12
8
Turn On/Off the E3+Receiver
1. Turn On: Press and hold the power button until MENU interface is
displayed on screen.
2. Turn off: Press and hold the power button until the LCD screen goes
blank.
USB Port
The rmware of E3+ receiver can be upgraded via the USB port, so as to
adjust its parameter and extend its compatibility with cameras to come in the
future.
1.1 Connect the USB cable to the computer and the other end of the USB
cable to E3+ receiver’s USB port. A mobile device icon will be displayed on
the computer when successfully connected.
1.2 Double click to start the upgrade software. The upgrade software can be
used to check version info, and upgrade the Base software, RF software and
Icon.
Click "Version" icon, the current version information of the connected E3+
transmitter will be displayed in the software window.
Click "Base software" icon, locate and double click on the FDS le from the
pop-out window. Then it starts loading the new rmware.
Click "RF software" icon, locate and double click on the RFC le from the
pop-out window. Then it starts loading the new rmware.
Other manuals for E3+
1
Table of contents
Other AODELAN Camera Accessories manuals
Popular Camera Accessories manuals by other brands
Viltrox
Viltrox EF-NEX Mount instructions
Calumet
Calumet 7100 Series CK7114 operating instructions
Ropox
Ropox 4Single Series User manual and installation instructions
Cambo
Cambo Wide DS Digital Series Main operating instructions
Samsung
Samsung SHG-120 Specification sheet
Ryobi
Ryobi BPL-1820 Owner's operating manual
