Anova Infinity Modular Seating System User manual

Assembly Instructions

Component parts:

Hardware Needed:

800.231.1327

[email protected]om

Tools Needed:

• 3/4” Hex Wrench

• 3/4” Hex Socket with Ratchet

• 7/16” Hex Wrench

• 7/16” Hex Socket with Ratchet

• Retractable Measuring Tape

• Pencil

Innity Powder Coated Benches

Innity Modular Seating System

Single Section Assembly:

Seating Sections End Caps Joining Straps Supports

1/2" Stainless

Steel Washers

1/4" Stainless

Steel Washers

1/2"-13 x 1.25" Stainless

Steel Hex Head Bolts

1/4"-20 x 1" Stainless

Steel Hex Head Bolts

1/2"-13 Stainless

Steel Hex Nuts

1/4"-20 Stainless

Steel Hex Nuts

Supports End Caps and Joining Straps

NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads. During

initial assembly, only tighten hardware to nger-tight until assembly is complete. Assembly of any Innity

bench requires at least two people.

1. Inspect the shipping container contents for damaged or missing components. Quantities will vary depending on

conguration and order.

a. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish. It is

recommended that the parts be positioned where the bench will be installed as once the bench is fully

assembled it may be too big and heavy to reposition.

Innity Powder Coated Benches

Assembly Instructions

2. Locate the End Caps to the bench and attach them

to the end of the bench using the included end cap

hardware.

a. For Linear Sections: Find one of the

two identical End Caps and slot it into the

end of the bench. Repeat this step on the

other end of the bench. Secure the End Cap

to the Seat Section using the included end

cap hardware with a 7/16”socket set and

wrench. (congure hardware in assembly as

shown below).

b. For Curved Sections: Determine the Left

and Right End Caps and slot them into the

end of the bench. Repeat this step on the

other end of the bench. Secure the End Cap

to the Seat Section using the included end

cap hardware with a 7/16”socket set and

wrench. (congure hardware in assembly as

shown below).

c. If you are assembling multiple sections

together, the End Cap will only be installed

on the end of the total bench not each

section. Continue to next page for Multiple

Section Assembly.

3. Position the Seat Section on top of the Supports

by lining up the holes on the underside of the

Seat Section to the mounting tabs on top of the

supports. Secure the Seat Section to the Supports

by using the included support hardware with a

3/4” socket set and wrench (congure hardware in

assembly as shown below).

Bolt Washers Nut

Support SupportSeat Section

End Cap End Cap

• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,

missing, or broken hardware, and general instability

• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced

• Repairs must be made using only factory authorized parts and methods.

WARNING

• Do not drag the assembled unit across any surface.

• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove

surface dirt. Do not clean with a solvent or petroleum based products.

CARE AND

MAINTENANCE

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

Innity Powder Coated Benches

Assembly Instructions

Assembling Multi-Section Innity Benches:

4. If assembling bench sections together into a

larger modular unit, assemble each section in the

modular unit and align the benches end-to-end.

5. Use Joining Straps to connect each section of

the modular bench together. The Joining Straps

will vary depending on the radius of your bench

section. When assembling, the faces of the

Joinings Straps should be ush with the outer

faces of the Seat Section Supports. Secure the

Joining Straps to the two Seat Sections using

the included joining strap hardware with a 7/16”

socket set and wrench.

REMINDER: It is recommended that the hardware

used in the assembly only be hand-tight until the

entire unit is assembled.

6. Once the modular bench is completely

assembled, be sure to install the End Cap on the

opposite end of the run of benches by repeating

Step 2.

5a 5b

This manual suits for next models

Table of contents

Popular Outdoor Furnishing manuals by other brands

Belleze

Belleze 014-HG-20074 manual

Hatteras Hammocks

Hatteras Hammocks DCA1-K-HH instructions

Kozyard

Kozyard Morgan Aluminum Pergola Assembly manual

Lemeks

Lemeks Palmako PA120-5959 Assembly, installation and maintenance manual

Polywood

Polywood 400 Series Assembly instructions

OLT

OLT 24 Assembly manual

forest-style

forest-style HACIENDA 2354 Building instructions

Courtyard Creations

Courtyard Creations RUS0188-WM Assembly instructions

RPR

RPR OLLIE CHAIR manual

kingsley-bate

kingsley-bate MC-55 Assembly instructions

Weltevree

Weltevree Carrier product manual

Grange Fencing

Grange Fencing Elite Arch Assembly instructions

Grosfillex

Grosfillex AUVENT YR14 Assembly instructions

X-METAL

X-METAL EAGLE 33511 Assembly instructions

Outsunny

Outsunny 84A-090 manual

Ivy Terrace

Ivy Terrace IVTD212 Assembly instructions

Breezesta

Breezesta FANBACK ADIRONDACK AD-0101 Assembly

hanit

hanit SUTTON 1 Assembly instructions