AMP Lighting AviatorPro Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE

Help Hotline:

1-813-978-3900 • Mon-Fri 9am-6pm (EST)

www.amplighting.com

AMP®Low Voltage Landscape Lighting

AMP® AviatorPro

BDL-GGT1-B-BZ

AMP®AviatorPro

BDL-GGT1-B-BZ

INSTALLATION & MAINTENANCE GUIDE

www.amplighting.com

–2–

Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes

and the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the

warranty.

These instructions do not intend to cover all variations in installation,

operation maintenance or mounting situations.

1. Make sure the power is turned OFF before installing or servicing this

luminaire.

2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)

or more from pool, spa or fountain.

3. This luminaire is intended to be used only with a power supply

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. Wiring connections must be made with UL listed wire connectors that are

suitable for outdoor use.

5. Position the low voltage wire and wire connector so that it is located

within 6 inches (15.2 cm) from a building structure, a luminaire or

tting.

6. The main low voltage cable is intended for shallow burial - less than 6

inches (152 mm).

7. If additional lengths of low voltage cable are required, please contact

www.amplighting.com or call 1-813-978-3900.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.

2. Lamp gets HOT quickly! Contact only switch/plug when turning on.

3. Do not touch the hot lens, guard or enclosure.

4. Keep lamp away from materials that may burn.

5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may

damage lamp.

6. Do not operate the luminaire tting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900

Parts Required (sold separately)

–3–

Package Contents

Remove Glare Guard and Shield from Fixture

A. (1) Fixture

A. (3) Self-tapping Screws

B. (3) Wall Anchors

C. (1) LED MR16 Lamp

Product Dimensions

5.00”

2.55”

3.10”

Glare Guard

Lens

Screw

Fixture

Use a screwdriver to loosen the set

screw. Then, remove the glare guard

from the lens. Next, remove the lens

from the xture.

INSTALLATION & MAINTENANCE GUIDE

–4–

www.amplighting.com

–4–

AMP®AviatorPro

BDL-GGT1-B-BZ

Install Lamp

Install Lens and Glare Guard

Lamp

Socket

Insert the lamp with correct

wattage and type marked on the

xture label.

CAUTION: Do not exceed maximum

wattage marked on luminaire label.

NOTE: DO NOT touch lamp with

bare hands. Use soft cloth to

handle lamp.

Set Screw

Lens

Glare Guard

Fixture

Place the lens over the lamp and

thread onto the xture. Tighten

until snug. Attach the glare guard

back onto the lens and secure with

the set screw. Tighten until snug

with a screwdriver.

[email protected] • 813.978.3900

–5–

INSTALLATION & MAINTENANCE GUIDE

AMP®AviatorPro

BDL-GGT1-B-BZ

Install Fixture

Wire Connections

Determine your desired location for

the xture. Pass self-tapping screws

through the holes on the surface

mount. Thread self-tapping screws

into the wall surface to secure the

xture.

*This xture must be installed

under an eave or overhang.

NOTE: Wall anchors are required

for brick walls or concrete walls.

To determine locations for the wall

anchors, place the surface mount

onto your desired location and

mark the points from the holes in

the mount.

Fixture

Self-tapping Screw

Wall Anchors

Fixture

Pigtail

Transformer

(sold separately)

Supply Cable

Strip both leads from the luminaire pigtail. Using two wire connectors

(sold separately), connect the leads from the luminaire to the main

supply cable leads.

INSTALLATION & MAINTENANCE GUIDE

–6–

www.amplighting.com

–6–

Install/Replace Lamp

AMP®AviatorPro

BDL-GGT1-B-BZ

Adjust Angle of Lamp

Knuckle

Adjustment

Loosen the knuckle and adjust the

luminaire to your desired angle and

then tighten adjustment screw.

Loosen the set screw on the glare guard, then remove the glare guard and

lens to expose the lamp. Replace it with the correct wattage and type

marked on the xture label. Finally, reinstall the lens and glare guard, then

tighten the set screw.

IMPORTANT: Bulbs must be protected from moisture and dust at all

times. Always reinstall lens and glare guards when removed.

–6––6–

[email protected] • 813.978.3900

–7–

IS-AAC-AL-GGT1-B-BZ-ver1.pdf

Specications and product details subject to change without notice.

[email protected] • 813.978.3900

Help Hotline:

1-813-978-3900 • Mon-Fri 9am-6pm (EST)

www.amplighting.com

Table of contents

Other AMP Lighting Landscape Lighting manuals

AMP Lighting

AMP Lighting TuscanPro AHT-3517-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting OrchardPro APL-3018-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting APL-3024-4-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting APL-301X-XX-4-B-BZ Series Operating and safety instructions

AMP Lighting

AMP Lighting FoundationPro Paver Light Operating and safety instructions

AMP Lighting

AMP Lighting PinnaclePro AAL-1016-40-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting AFL-401-LI-A-BZ Series Operating and safety instructions

AMP Lighting

AMP Lighting PolynesianPro Operating and safety instructions

AMP Lighting

AMP Lighting PillarPro APL-3019-4-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting KinglyPro APL-3020-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting 3601 Series Operating and safety instructions

AMP Lighting

AMP Lighting HydraPro AUL-8001-25-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting BulletPro MR8 Operating and safety instructions

AMP Lighting

AMP Lighting PinnaclePro Mini Operating and safety instructions

AMP Lighting

AMP Lighting VAC-ZWM1-BBZ Operating and safety instructions

AMP Lighting

AMP Lighting ASSI-9008-50-BK Operating and safety instructions

AMP Lighting

AMP Lighting EscherPro MR11 Operating and safety instructions

AMP Lighting

AMP Lighting MR16 HydraPro Operating and safety instructions

AMP Lighting

AMP Lighting ADL Series Operating and safety instructions

AMP Lighting

AMP Lighting Sol Box Brass ASDL-2014-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting HydraPro AWL-5005-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting PinnaclePro AAL-1017-4-B-BZ Operating and safety instructions

AMP Lighting

AMP Lighting 3602 Series Operating and safety instructions

AMP Lighting

AMP Lighting AFL-4010-4-B-BZ Operating and safety instructions

Popular Landscape Lighting manuals by other brands

Intex

Intex SL1006 owner's manual

LED Group

LED Group ROBUS R2IN13W quick start guide

Patriot Lighting

Patriot Lighting 343-1484 installation manual

Hess

Hess SERA G: SERA S Installation and operating instructions

LIGMAN

LIGMAN JET 44 installation manual

LIGMAN

LIGMAN MALTA 1 installation manual

Cooper Lighting

Cooper Lighting MCGRAW-EDISON WBG Specification sheet

Cooper Lighting

Cooper Lighting Invue 42 - 175W Specification sheet

Saxby Lighting

Saxby Lighting Islay 68784 Instruction leaflet

LIGMAN

LIGMAN EU-10016-3 installation manual

Cooper Lighting

Cooper Lighting McGraw-Edison ZD Credenza specification

LIGMAN

LIGMAN KI-60475 installation manual

Cooper Lighting

Cooper Lighting Generation CLB25MWW5C373 Specification sheet

Malibu Boats

Malibu Boats CL905K instructions

LIGMAN

LIGMAN NYB-30161 installation manual

LIGMAN

LIGMAN SI-80021 installation manual

Volt

Volt 2-in-1 Tiki-Brass Torch Light installation instructions

Malibu Boats

Malibu Boats CM110P instructions