Alpine KTX-CMY8-S User manual

Mobile

Media

Solutions

Perfect Fit 2012-up Toyota Camry (Excluding

Introduction

models with JBL)

KTX-CMY8-S

Power Harness x 1 KCX-SWCTY

Steering Wheel Interface

Module x 1

Left Bracket x 1

(Panel 7340) Right Bracket x 1

(Panel 7339)

This KTX-CMY8-S Perfect Fit installation kit is

for

Select 2012+ Toyota Camry vehicles (exclud-

ing models with JBL). Included are all the parts needed

install your Alpine INE-Z928HD Audio

Video Navigation system in Select 2012+ Toyota Camry vehicles. KTX-CMY8-S Perfect Fit

installation kit also includes

interface module that allows steering wheel remote control

the

Alpine system. Refer

the individual instruction sections

this manual

remove your vehicle's

factory radio and assemble the kit.

Caution!

Disconnect

your

vehicle's

negative

battery

terminal

before

the

installation

help

prevent

electrical

damage.

recommend

the

use

digital

multimeter

check

vehicle

wiring.

not

use

test

light!

test

light

grounded

wire

probe

can

cause

damage

the

vehicle's

computer

and/or

diagnostic

systems.

Avoid

all

factory

airbag

wiring.

Airbags

can

accidentally

deploy

causing

serious

injury

even

death.

Notes:

• See your vehicle's instructions

for

any special tools your installation might require.

• Read all instructions accompanying your

car

stereo for proper wiring and mounting

instructions.

Factory Stereo Removal

1. Use a Panel Removal Tool

unsnap

(2)

vertical

trim panels,

left

and right

sides

stereo.

Use a Panel Removal Tool

carefully unsnap and

remove

vent

assembly above

the

stereo. Use a Panel

Removal Tool

carefully unsnap

clock

panel

the

top

dash. Tilt

clock

panel

away

clear

access

for

stereo removal

Extract

(2)

Omm

bolts

above radio (from

vent

cavity).

Extract

(2)

Omm

bolts

the

lower

left

and

right

HVAC controls.

5. Trim across

the

entire plastic

bracket

/2"

make

room

for

the

head unit.

Lift radio/HVAC

stack

out

dash,

unplug

all

connectors

and remove. Extract

(2)

Phillips head

screws from each inner

side

the

HVAC control

module

separate from Factory

bracket

assembly.

Mounting The Stereo

Attach

brackets 7340 and 7339

the

Alpine head

unit

using the ISO screws (that come with

the

head

unit).

2. Plug in

the

supplied radio harnesses and steer-

ing wheel controls. Run Bluetooth

mic

GPS

antenna, and install

foot

brake and parking brake

wires.

3. Attach the Factory

HVAC

module within

the

7340 and 7339 brackets

below

the head

unit

(re-

use Factory screws.)

4. Connect head unit

factory HVAC module and

mount

in dash re-using the

factory

hardware.

Snap the Perfect Fit trim panel

into

the dash

(around the head unit/HVAC controls). Re-as-

semble final

trim

pieces in reverse order.

Steering Wheel Controls

Steering

Wheel

Control Operation

(when

vehicle

is equipped)

1. Answer

Mute

3. Hang

4. Source

Seek/Track Down

6. Volume Down

7. Volume

8. Seek/Tra

Wiring Harness Diagram

Toyota Camry

Vehicle Harness

not use

201

0-up

....

-----------------

Steering (

0 •

Wheel connector : :

(20-pin)

i i

Use 28-Pin Steering

! :

Wheel connector

\...

.--------------.

Parking

Brake(-)

at the parking brake Yellow/Blue

drivers kick panel

aftermarket Blue/White

amplifier remote

turn on

Reverse

Trigger

(+).

Use only with a Orange/White

back

camera

(+)

side of the reverse

light

Liability Disclaimer ,

Steering Wheel

Remote Control

Module

Head Unit

Steering Remote

INE-Z928HD

Audio

Video

Navigation

System

Input (Pigtail)

._____

___

---~

Due

changes in design and manufacturing that may

occur

with

your

specific vehicle,

important

that

you

not

rely solely on vehicle information contained in this installation

manual, such as dash disassembly, wire harness, and codes. Such information should be

confirmed with the vehicle manufacturer. Alpine Electronics, Inc. and its affiliated companies

not

responsible

for

damage that may

occur

you

your automobile during the installation

the Perfect Fit Kit.

you have any further questions, feel free

contact Alpine Tech

Support

1-800-NAV-HELP.

ALPINE ELECTRONICS OF AMERICA, INC., 19145 Gramercy Place, Torrance, CA 90501, U.S.A

ALPINE ELECTRONICS OF CANADA, INC., 777 Supertest Road, Toronto, Ontario M3J 2M9,

Canada

not

send products to these addresses.

Call the toll free number

visit the website

locate a service center.

Other Alpine Automobile Accessories manuals

Popular Automobile Accessories manuals by other brands

James Baroud

James Baroud Odyssey user guide

Motorola

Motorola i50sx owner's manual

Yakima

Yakima 9MM STANDARD BIKE MOUNT instructions

Feniex

Feniex T3 instruction manual

Renault

Renault 77 11 423 180 Installation instruction

Kia

Kia E8300-4D000 manual

Brink

Brink 756843 installation instructions

Whispbar

Whispbar K085W Fitting instructions

v.link

v.link CI-VL2-PC-HSD manual

Viking

Viking Stack-Rack Assembly and use instructions

Aries

Aries 203015 installation manual

Choetech

Choetech AT0005 user manual

ZZ2

ZZ2 ZZAIR-PRO instruction manual

Holman

Holman 4A80L installation guide

Thule

Thule 2075 parts manual

Motorola

Motorola T325 quick start guide

TAUBENREUTHER

TAUBENREUTHER 16-3950 FITTING INSTRUCTION

DV8

DV8 FBJL-02 Product installation manual