AllMounts AS0246TP User manual

ISSUED: JUL. 2014

TV Floor Stand and Accessories

INSTALLATION MANUAL

CAUTION: DO NOT EXCEED

RATED LISTED WEIGHT. SERIOUS

INJURY OR PROPERTY DAMAGE

MAY OCCUR!

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your distributor if you have any questions.

+5°

-12°

AS03V

Note: The accessories are not standard equipped.

The accessories will be selected according to user

requirement.

AS02

AS02H

AS01K

AS02R

AS02P

Optional Accessories

16. Adjustment

300x300/400x200

400x400/600x400

AS0246TP

70"

MAX 65kg

(143lbs)

RATED

65kg

(143lbs)

RATED

10kg

(22lbs)

RATED

10kg

(22lbs)

RATED

All accessories

0°~+90°

Rotate the display

clockwise and use

the screw to secure

the display.

Adjust or tilt the

display to the

required position.

WARNING

NOTE: Read the entire instruction manual before you start installation and assembly.

Package M

washer

M-F

(x4)

M8x20

M-C

(x4)M5x14

M-A

(x4) M6x14

M-B

(x4)

big spacer (x4)

M-H

M6x30

M-D

(x4)

M8x30

M-E

(x4) small spacer (x8)

M-G

• Do not begin the installation until you have read and understood all the instructions

and warnings contained in this installation sheet. If you have any questions

regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as

specified in this manual. Improper installation of this product may cause damage

or serious injury.

• Always use an assistant or mechanical lifting equipment to safely lift and position

the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can cause damage

to the items, This greatly reduces their holding power.

• This product is intended for indoor use only. Using this product outdoors could

lead to product failure and personal injury.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.

If any parts are missing or faulty, telephone your local distributor for a replacement.

AS0246TP

connecting plate (x1)

column (x1)

3mm Allen key (x1)

5mm Allen key (x1)

6mm Allen key (x1)

top cover (x1)

cable clamp (x4)

M6x10 (x2)

M8x16 (x4)

wrench (x1)

universal plate (x1)

plastic cap (x2)

adapter bracket

(x2)ST4.2x9.5 (x4)

stopper bolt (x4)

rubber pad (x4)

iron expansion bolt (x6)

steel plate (x1)

M6x20 (x4)

D6 washer (x4)

M8x16 (x6)

M8x40(x4)

1. Installing the Rubber Pads

2. For the model AS01K installation

(Assembly based on the accessories selected by user.)

Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a

phillips screwdriver.

P-G

AS02H

AS02

AS03V/AS02P

AS02R

CPU holder (x1)

T-A

Package P

laptop cabinet (x1)

T-D

support rod (x2)

T-F

camera shelf (x1)

T-G

connecting piece (x1)

T-B

silicone pad (x8)

P-C

DVD shelf (x1)

T-C

Package P

key (x1)

P-F

M6x8 (x4)

P-D

AS01K

power socket (x1)

T-H

M6x8 (x4)

P-A

4mm Allen key (x1)

P-B

AS03V only

D6 washer (x4)

P-E

connecting piece (x1)

T-E

ST4.8x9.5 (x4)

P-G

The following accessories are optional.

3a. For Concrete Floor Mounting

60mm

(2.4")

62mm

(2.4")

ø12mm

(ø 1/2 ")

T-H

• Lift the steel base by grasping the cable ties.

• Peel off the backing paper from the rubber pads and stick the rubber

pads on to the steel base.

Mark the exact location of mounting holes and pre-drill these mounting holes with a 12mm drilling bit to

at least 62mm in depth. Remove the dust in the holes.

First tighten the iron expansion bolts with an Allen key,

and then loosen the iron expansion bolts in order to

separate the bolts and the expansion tubes.

• Attach the connecting plate to the bottom of the column using the appropriate

screws. Tighten all screws with an Allen key.

• Insert an expansion tube into each of these holes. Using the bolts mount the

column to the floor. Tighten all screws with an Allen key.

3b. For the Floor Stand Mounting

4-2: Installing the CPU holder on the side of the column

(If the power socket is installed on the back of the column)

Loosen and remove the screws in order to separate the metal plate from the connecting piece.

Attach the removed metal plates to the CPU holder using the removed screws.

Tighten all screws with an Allen key.

Insert the CPU holder to the required position along the column rails. Tighten all screws to secure

it with an Allen key.

metal plate

4. For the model AS02H installation

(Assembly based on the accessories selected by user.)

P-A

4-1: Installing the CPU holder on the back of the column

Insert the CPU holder to the required position along the column rails. Tighten all screws to secure

it with an Allen key.

Peel off the backing paper

from the silicone pads and

stick the silicone pads on

to the CPU holder.

Attach the connecting piece to the CPU holder using the appropriate screws. Tighten all screws

with an Allen key.

NOTE: With the arrow pointing upward.

P-B

P-C

T-B

T-A

Remove the cable ties.

Attach the column to the steel base using the appropriate screws. Tighten all screws with an Allen key.

7. Separating the Universal Plate and the Support Bracket

5. For the model AS02 installation

(Assembly based on the accessories selected by user.)

Insert the DVD shelf to the required position along the column rails. Secure it by tightening screws with an

Allen key.

Insert the laptop cabinet to the required position along

the column rails, Tighten all screws to secure it with

an Allen key.

• n

• Use the adjustable buckles to hold the machine firmly in place.

Loosen the k obs to adjust the space for CPU.

buckle

6. For the model AS03V installation

(Assembly based on the accessories selected by user.)

NOTE: With the arrow

pointing upward.

P-D

P-E

Attach the connecting piece to the laptop

cabinet using the appropriate screws and

washers. Tighten all screws to secure it with

a proper phillips screwdriver.

T-E

T-D

T-C

knob

Loosen and remove the nuts in order to separate the universal plate from the universal plate assembly.

Slide the adapter brackets

into the universal plate.

• Insert the stopper bolts into both ends of

the universal plate to prevent the adapter

brackets from slipping off.

• Attach both plastic caps to both ends

of the universal plate using the appropriate

screws.

• Tighten all screws with a proper screwdriver.

universal plate

support plate

8. Installing the Universal Plate

9. Installing the Adapter Brackets

M-G

M-F

M-D/M-E

M-H

M-F

M-D/M-E

M-H

9-1 For Flat Back Screens

Top of the display

M-A/M-B/M-C

M-F

9-2 For Recessed Back Screens or to Access A/V Inputs

Tighten all screws but do not over tighten.

· Position the adapter brackets as close as possible to the center of the display.

· Screw the adapter brackets onto the display.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

or or or

M-G

M-C

M-F

M-G

M-F

M-C M-D/M-E/

5mm

Adjust the adapter brackets to align with display mounting holes, then tighten all screws using a proper

screwdriver.

Install the two nuts (the removed in previous step) on the

upper pins and leave a 5mm space to the universal plate.

upper pins

lower pins

13. For the model AS02R installation

(Assembly based on the accessories selected by user.)

Tighten the support rods to the camera shelf.

Remove two plastic caps for the camera shelf installation.

T-G

T-F

10. Hooking the Support Plate onto the Aluminum Column

11. Hooking the Display onto the Support Plate

Attach the top cover to the column using the

appropriate screws. Tighten all screws with an

Allen key.

12. Cable Management

Insert the cable clamps horizontally into the plate slots, then turn the cable clamps to the vertical position

to secure them.

Insert the support plate along the column rails to the required position and tighten all screws with an Allen key.

Lift the display carefully and hook the display onto the support bracket. Place the lower nuts and use a

wrench to tighten all nuts.

Insert the support rods to the required position along the column slots and tighten both screws to secure

the camera shelf.

Use the key to open the laptop cabinet.

14. For the model AS02P installation

(Assembly based on the accessories selected by user.)

Attach the laptop cabinet to the connecting piece on the universal plate using the appropriate screws.

Tighten all screws with a proper phillips screwdriver.

Put the laptop into the cabinet gently , then close the box and lock it.

T-D

P-D

P-E

P-F

laptop

15. Cable Management

Run the cables through

the cable clamps.

Other AllMounts Rack & Stand manuals

AllMounts

AllMounts AS64F User manual

AllMounts

AllMounts AS0246BTW User manual

AllMounts

AllMounts AS0946T User manual

AllMounts

AllMounts AS01346FP User manual

AllMounts

AllMounts AS01T01 User manual

AllMounts

AllMounts PLB-43S User manual

AllMounts

AllMounts AS01346FW User manual

AllMounts

AllMounts AS0346T User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 