AllMounts AS01346FP User manual

AS01K

ISSUED: OCT. 2014

Video Wall Stand and Accessories

INSTALLATION MANUAL

CAUTION: DO NOT EXCEED

RATED LISTED WEIGHT. SERIOUS

INJURY OR PROPERTY DAMAGE

MAY OCCUR!

300x300/400x200

400x400/600x400

AS01346FP

55"

MAX

50kgx3

(110lbsx3)

RATED

50kgx3

(110lbsx3)

RATED

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your distributor if you have any questions.

Note: The accessories

are not standard equipped.

The accessories will be

selected according to

user requirement.

Optional Accessories

21 3

Note: The displays are installed by the numerical order given.

Note: The angle of displays are adjusted by the numerical order given.

879

WARNING

NOTE: Read the entire instruction manual before you start installation and assembly.

• Do not begin the installation until you have read and understood all the instructions

and warnings contained in this installation sheet. If you have any questions

regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as

specified in this manual. Improper installation of this product may cause damage

or serious injury.

• Always use an assistant or mechanical lifting equipment to safely lift and position

the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can cause damage

to the items, This greatly reduces their holding power.

• This product is intended for indoor use only. Using this product outdoors could

lead to product failure and personal injury.

Component Checklist

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation.

If any parts are missing or faulty, telephone your local distributor for a replacement.

AS01346FP

Package M (x3)

washer

M-F

(x4)

M8x20 (x4)

M-C

M5x14 (x4)

M-A

M6x14 (x4)

M-B

big spacer (x4)

M-H

M6x30 (x4)

M-D

M8x30 (x4)

M-E

small spacer (x8)

M-G

AS01K (The following accessories are optional)

power socket (x1)

T-H

ST4.8x9.5 (x4)

P-G

adapter bracket (x6)

universal plate (x3)

connecting fitting (x3)

steel plate (x1)

rubber pad (x4)

column (x1)

connecting plate (x1)

top cover (x1)

iron expansion bolt (x6)

cable clamp (x12)

M8x16 (x4)

M8x16 (x6)

M8x40(x4)

5mm Allen key (x1)

6mm Allen key (x1)

3mm Allen key (x1)

4mm Allen key (x1)

1. Installing the Rubber Pads

3a. For Concrete Floor Mounting

60mm

(2.4")

60mm

2.4"( )

62mm

(2.4")

ø12mm

(ø 1/2 ")

• Lift the steel base by grasping the cable ties.

• Peel off the backing paper from the rubber pads and stick the rubber

pads on to the steel base.

Mark the exact location of mounting holes and pre-drill these mounting holes with a 12mm drilling bit to

at least 62mm in depth. Remove the dust in the holes.

First tighten the iron expansion bolts with an Allen key, and then loosen the iron expansion bolts in order

to separate the bolts and the expansion tubes.

2. For the model AS01K installation

(Assembly based on the accessories selected by user.)

Attach the power socket to the back of column using the appropriate screws. Tighten all screws with a

phillips screwdriver.

T-H

P-G

4. Installing the Universal Plates

3b. For the Floor Stand Mounting

Remove the cable ties.

Attach the column to the steel base using the appropriate screws. Tighten all screws with an Allen key.

• Attach the connecting plate to the bottom of the column using the

appropriate screws. Tighten all screws with an Allen key.

• Insert an expansion tube into each of these holes. Using the bolts

mount the column to the floor. Tighten all screws with an Allen key.

Insert the universal plates to the column along the column rails respectively.

NOTE: With the arrow pointing upward.

5. Installing the Top Cover

Attach the top cover to the column using the

appropriate screws. Tighten all screws with an

Allen key.

6. Installing the Adapter Brackets

Top of the display

6-1 For Flat Back Screens

TV M-A/M-B/M-C

M-F

Tighten all screws to

secure them with an

Allen key.

X+5mm

(X=Height of display)

X+5mm

(X=Height of display)

M-D/M-E

M-F

M-G

M-H

M-D/M-E

M-F

M-G

M-F

M-C/M-D/M-E

M-C

M-F

M-G

6-2 For Recessed Back Screens or to Access A/V Inputs

Tighten all screws but do not over tighten.

• Position the adapter brackets as close as possible to the center of the displays.

• Screw the adapter brackets onto the displays.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screens.

or or or

• Lift the display carefully and pull downward two straps at

the same time , then hook the adapter brackets to the

universal plate. Fasten the adapter brackets to the universal

plate by releasing the straps.

• The other displays are hung onto the universal plates in the

same way

Use the padlocks to prevent

the displays from being stolen

(The padlocks are not included).

7. Hanging the Displays onto the Universal Plates

8. Micro-Adjustment

If the displays uptilted, rotate the adjustment screws as shown in figure.

Note: Adjust the

angle of displays

by the numerical

order given.

Note: The displays are

installed to the universal

plates from the bottom

up.

If the displays tilted down, rotate the adjustment screws as shown in figure.

1mm

Note: Leave a one

millimeter gap between

the displays.

9. Cable Management

Insert the cable clamps horizontally into the plate slots, then turn the cable clamps to the vertical to

secure them.

Run the cables through the cable

clamps and the rubber strip.

Rotate the adjustment screws as shown in figure to make a one millimeter gap left between the displays.

up down

+3° -3°

10. Adjustment 11. Multi-screen Combination Solution

Loosen the screws in the

plastic covers in order to

remove the plastic covers.

Remove the screws attaching

the front of the universal plates.

Connecting attachment

Loosen the screws in the connecting fittings

in order to slide the connecting attachments

to both sides of the connecting fittings.

Then tighten all screws to secure.

X+5mm

(X=Height of display)

X+5mm

(X=Height of display)

X+5mm

(X=Height of display)

X+5mm

(X=Height of display)

Insert the connecting fittings

to the appropriate position

along the universal plates rails.

Note: Make sure that the

universal plates are at the

same level with each other. Smaller display

Note: The position which the connecting

fittings insert to the universal plate is

determined by the size of displays.

Use the connecting fittings to assemble the

other stand.

Note: Make sure that the stands are in

alignment.

Tighten all screws to secure them.

Larger display

Note: The angle of displays are adjusted by the numerical order given.

Note: Leave a one

millimeter gap between

the displays.

1mm

Note: The displays are installed by the numerical order given.

Other AllMounts Rack & Stand manuals

AllMounts

AllMounts AS0246TP User manual

AllMounts

AllMounts AS0346T User manual

AllMounts

AllMounts AS64F User manual

AllMounts

AllMounts AS01T01 User manual

AllMounts

AllMounts AS0246BTW User manual

AllMounts

AllMounts AS01346FW User manual

AllMounts

AllMounts AS0946T User manual

AllMounts

AllMounts PLB-43S User manual

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 