Alliance Laundry Systems CTS90AWN User manual

Para bajar una copia de estas instrucciones en español, visite www.speedqueen.com.

Keep these instructions for future reference.

(If this machine changes ownership, this manual must accompany machine.)

www.speedqueen.com

Installation Instructions

for Frontload Washers

Washer Dimensions........................................................... 2

Before You Start................................................................ 2

Installation......................................................................... 3

Installer Checklist.............................................................. Back Cover

Date Purchased ________________

Model Number ________________

Serial Number _________________

Part No. 801988

August 2004

Inside.....................................

Washer Dimensions

Before You Start

Supplies

For most installations, the basic supplies you will need

are:

Parts Included

An accessories bag has been shipped inside your

washer. It includes:

•Two fill hoses with washers and filter screens.

Refer to step 2 of Installation.

•Four rubber feet. Refer to step 4 of Installation.

•Beaded strap. Refer to step 3 of Installation.

•Installation Instructions.

•User’s Guide.

•Product Registration Card.

•Warranty Bond.

•Bag for storing shipping materials.

NOTE: If the washer is delivered on a cold day

(below freezing), or is stored in an unheated room

or area during the cold months, do not attempt to

operate it until the washer has had a chance to

warm up.

NOTE: Some moisturein the wash drum is normal.

Water is used during testing at the manufacturer.

NOTE: Install dryer before washer. This allows

room for attaching exhaust duct.

FLW2044N

Figure 1

FLW2044N

2 in. (5.1 cm)

26.9 in. (68.3 cm)

28 in. (71.1 cm)

41.2 in. (104.6 cm)

31.1 in. (79 cm)

29.6 in. (75.1 cm)

18.7 in. (47.5 cm)

14.3 in.

(36.3 cm)

FLW2045N

1 Safety Glasses

2Wood Block

3Wrench

4Screwdriver

5Pliers

6Socket Wrench

7Level

Figure 2

801988

Installation

Step 1: Position Washer Near Installation

Area

Move washer as close to the desired area of

installation as possible.

Step 2: Connect Fill Hoses

Water Supply

Water supply faucets must fit standard 3/4 inch

(19.1 mm) female garden hose couplings. DO NOT

USE SLIP-ON OR CLAMP-ON CONNECTIONS.

Water supply faucets should be readily accessible to

permit turning them off when washer is not being

used.

Recommended cold water temperature is 50o to 75o

Fahrenheit (10oto 24oCelsius). Recommended hot

water temperature is 140oto 150oFahrenheit (60oto

66oCelsius). Warm water is a mixture of hot and cold

water. Warm water temperature is dependent upon

water temperature and pressure of both the hot and

cold water supply lines.

Water pressure must be a minimum of 20 to a

maximum of 120 pounds per square inch (138 to 827

kPa) static pressure measured at the faucet.

NOTE: Water pressure under 20 pounds per

square inch (138 kPa) will cause an extended fill

time in the washer and may not properly flush out

the detergent dispenser.

Turn on the water faucets and flush the lines for

approximately two minutes to remove any foreign

material that could clog the screens in the water

mixing valve.

NOTE: When installing in newly constructed or

renovated buildings, it is very important to flush

the lines since build-up may have occurred during

construction.

Connecting Hoses

Remove the two plain rubber washers and two filter

screens from the accessories bag. Install them into

each end of the fill hoses as shown in Figure 3. The

screen must be facing outward.

Screw hose couplings with the filter screens onto the

water faucets until they are finger-tight. Then, using a

pliers, screw approximately 1/4 turn. Use the red

color-coded hose for the hot water connection and the

blue color-coded hose for the cold water connection.

Screw hose couplings from other end of hoses onto the

water mixing valve until they are finger-tight. Then,

using a pliers, screw approximately 1/4 turn. Refer to

Figure 4. Make sure the red color-coded hose from the

hot water faucet goes to the water mixing valve

marked “H” and the blue color-coded hose from the

cold faucet goes to the valve marked “C”.

IMPORTANT: Do not cross thread or overtighten

couplings. This will cause them to leak.

Turn water on and check for leaks. If leaks are found,

turn off the water, unscrew hoses and reinstall them

until there are no leaks.

IMPORTANT: Turn off water supply whenever

there will be an extended period of non-use.

Under certain conditions, hydrogen gas

may be produced in a hot water system

that has not been used for two weeks or

more. HYDROGEN GAS IS EXPLOSIVE. If

the hot water system has not been used

for such a period and before using the

washer, turn on all hot water faucets and

let the water flow from each for several

minutes. This will release any

accumulated hydrogen gas. The gas is

flammable. Do not smoke or use an open

flame during this time. W029

WARNING

TLW1976N

1 Water Faucet

2Blue Fill Hose

3Plain Rubber Washer

4Hose Coupling

5Red Fill Hose

6Filter Screens

Figure 3

HOT

COLD

IMPORTANT: Hoses and other natural rubber

parts deteriorate after extended use. Hoses may

develop cracks, blisters or material wear from the

temperature and constant high pressure they are

subject to.

All hoses should be checked on a yearly basis for

any visible signs of deterioration. Any hose showing

the signs of deterioration listed above should be

replaced immediately. All hoses should be replaced

every five years.

Step 3: Connect Drain Hose to Drain

Receptacle

Remove the drain hose from its shipping position on

the rear of the washer by unhooking the hose from the

retainer clamp and by removing the shipping tape.

Install the drain hose into the drain receptacle

(standpipe, wall or laundry tub) following the

instructions below.

IMPORTANT: Drain receptacle must be capable of

handling a minimum of 1-1/4 inch (32 cm) outside

diameter drain hose.

Standpipe Installation:

Place the drain hose into the standpipe.

Remove the beaded strap from accessories bag and

place around standpipe and drain hose and tighten

strap to hold hose to standpipe. Refer to Figure 5. This

will prevent the drain hose from dislodging from drain

receptacle during use.

Wall Installation:

For installations of this type, the drain hose MUST be

secured to one of the fill hoses using the beaded strap

from accessories bag. Refer to Figure 6.

NOTE: End of drain hose must be below 24 in.

(61 cm).

FLW1973N

1 Water Faucets

2Cold Water Connection

3Hot Water Connection

4Fill Hoses

Figure 4

FLW1973N

FLW1959N

1 24 in. to 36 in. (91.44 cm recommended

height)

2Standpipe - 2 in. (5.08 cm) or 1-1/2 in. (4 cm)

3Beaded Strap

Figure 5

H023I

1 Drain Hose

2Beaded Strap (tape if necessary)

3Fill Hoses

Figure 6

FLW1959N

801988

Laundry Tub Installation:

For this type of installation, the drain hose MUST be

secured to the stationary tub to prevent hose from

dislodging during use. Refer to Figure 7. Use the

beaded strap (supplied in accessories bag) to secure

hose.

Step 4: Position and Level the Washer

Position washer so it has sufficient clearance for

installation and servicing.

NOTE: Use of the dispenser drawer or washer door

as a handle in the transportation of the washer may

cause damage to the dispenser or door.

Place washer in position on a clean, firm and

reasonably level floor. Installing the washer on any

type of carpeting is not recommended.

For easier access to leveling legs, prop up washer with

a wooden block. Refer to Figure 8.

Place a level on the cabinet top and check if the washer

is level from side to side and front to back.

NOTE: Level must rest on raised portion of top

panel. Refer to Figure 9.

If washer is not level, tilt washer to access the front

and rear leveling legs. Loosen the locknuts and adjust

legs by screwing into or out of washer base.

Make sure that the washer does not rock. When washer

is level and does not rock, tighten locknuts securely

against bottom of washer base. If these locknuts are

not tight, washer will move out of position during

operation.

Do not slide washer across floor once the leveling legs

have been extended. Legs and base could become

damaged.

Place rubber feet (supplied in accessories bag) on all

four leveling legs. Refer to Figure 9.

Verify that washer does not rock.

Step 5: Remove the Shock Sleeves and

Shipping Brace

Remove front access panel by removing the two

screws at the bottom of the panel.

Remove the five bolts and lockwashers from shipping

brace with 9/16 inch wrench and remove brace. Refer

to Figure 10. Four bolts are located on the washer base

and one is holding the brace to the weight. Remove

shock sleeves by pulling on the yellow rope. Refer to

Figure 10.

FLW1961N

1 Drain Hose

2Beaded Strap (tape if necessary)

Figure 7

FLW2046N

1 Wood Block

Figure 8

FLW2047N

1 Level

2Rubber Foot

3Leveling Leg

4Locknut

5Washer Base

Figure 9

Make sure all four shock sleeves are removed. Remove

label from front side of front access panel and place on

backside of front access panel for future reference.

Store the shipping materials in the bag provided in the

accessories bag. Save materials for use whenever the

unit is moved.

Reinstall front access panel.

IMPORTANT: The shipping brace, bolts,

lockwashers and shock sleeves should be saved and

MUST be reinstalled whenever the unit is moved

more than four feet. Do not lift or transport unit

from front or without shipping materials installed.

Refer to the User’s Guide for proper instructions

on reinstalling the shipping materials.

IMPORTANT: DO NOT tip washer more than

6 inches (152.4 mm) in any direction after shipping

brace has been removed. Shock absorbers may

separate and damage to washer may result. For

leveling purposes, the washer may be tilted a

maximum of 6 inches (152.4 mm) in any direction.

Step 6: Wipe Out Inside of Washer Drum

Before using the washer for the first time, use an all-

purpose cleaner, or a detergent and water solution, and

a damp cloth to remove shipping dust from inside the

drum.

Step 7: Plug in the Washer

Washer requires 120 Volt, 60 Hertz electrical supply

and comes equipped with a 3-prong grounding plug.

Refer to serial plate for specific electrical

requirements.

FLW2048N

1 Shock Sleeves

2Motor Mount

3Hooked End of Shipping Brace

4Bolts and Lockwashers

Figure 10

FLW2048N

FLW2049N

Figure 11

DRY2022N

1 L1

2Ground

3Neutral Side

4Round Grounding Prong

5Neutral

Figure 12

123

Standard 120 Volt, 60 Hertz

3-Wire Effectively

Grounded Circuit

0 V.A.C.

120±12

V.A.C.

120±12

V.A.C.

801988

When plugging in the washer:

•DO NOT overload circuits.

•DO NOT use an extension cord.

•DO NOT use an adapter.

•DO NOT operate both a washer and gas dryer on

the same circuit. Use separately fused 15 Amp

circuits.

The washer is designed to be operated on a separate

branch, polarized, three-wire, effectively grounded,

120 Volt, 60 Hertz, AC (alternating current) circuit

protected by a 15 Amp fuse, equivalent fusetron or

circuit breaker.

The three-prong grounding plug on the power cord

should be plugged directly into a polarized three-slot

effectively grounded receptacle rated 110/120 Volts

AC (alternating current) 15 Amps. Refer to Figure 12

to determine correct polarity of the wall receptacle.

Grounding Information

The washer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current.

The washer is equipped with a cord having an

equipment-grounding conductor and a 3-prong

grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

Do not modify the plug provided with the washer - if it

will not fit the outlet, have a proper outlet installed by

a qualified electrician.

NOTE: Have a qualified electrician check the

polarity of the wall receptacle. If a voltage reading

is measured other than that in Figure 12, the

qualified electrician should correct the problem.

NOTE: The wiring diagram is located behind the

control panel, inside the control cabinet.

Step 8: Check Installation

Refer to Installer Checklist on the back cover of this

manual and make sure that washer is installed

correctly.

Run washer through one complete cycle to make sure

it is operating properly.

To reduce the risk of fire, electric shock or

personal injury, all wiring and grounding

MUST conform with the latest edition of

the National Electrical Code, ANSI/NFPA

70, and such local regulations as might

apply. It is the customer’s responsibility

to have the wiring, fuses and circuit

breakers installed by a qualified

electrician to make sure adequate

electrical power is available to the washer.

WARNING

W518

To reduce the risk of an electric shock or

fire, DO NOT use an extension cord or an

adapter to connect the washer to the

electric power source. W082

WARNING

Improper connection of the equipment-

grounding conductor can result in a risk

of electric shock. Check with a qualified

electrician or service person if you are in

doubt as to whether the washer is

properly grounded. W216

WARNING

This unit is equipped with a three-prong

(grounding) plug for your protection

against shock hazard and should be

plugged directly into a properly grounded

three-prong receptacle. Do not cut or

remove the grounding prong from this

plug. W213

WARNING

Installer Checklist

Fast Track for Installing the Washer

(Refer to the manual for more detailed information)

• Position Washer Near

Installation Area.

CHECK

• Connect Fill

Hoses.

FLW2054N

COLD

HOT

CHECK

Filter

Screens Cold Valve

Connection

Plain Washers

Red

Blue

Hot Valve Connection

FLW2054N

• Connect Drain

Hose to Drain

Receptacle.

CHECK FLW1959N

FLW1959N

FLW2047N

• Position and

Level the Washer.

CHECK FLW2047N

• Remove the Shock Sleeves

and Shipping Brace.

CHECK FLW2048N

FLW2048N

FLW2049N

• Wipe Out Inside of

Washer Drum

CHECK FLW2049N

• Plug in the Washer.

CHECK D254I

Table of contents

Other Alliance Laundry Systems Washer manuals

Alliance Laundry Systems

Alliance Laundry Systems 38899R8 User manual

Alliance Laundry Systems

Alliance Laundry Systems LWS01A*C series User manual

Alliance Laundry Systems

Alliance Laundry Systems UW35TV User manual

Alliance Laundry Systems

Alliance Laundry Systems AFNE9BSP113TN01 User manual

Alliance Laundry Systems

Alliance Laundry Systems FLW1511C User manual

Alliance Laundry Systems

Alliance Laundry Systems UM202 Series Owner's manual

Alliance Laundry Systems

Alliance Laundry Systems LWK23AW-3050 User manual

Alliance Laundry Systems

Alliance Laundry Systems UW35P3 Maintenance and service guide

Alliance Laundry Systems

Alliance Laundry Systems CHM1772C User manual

Alliance Laundry Systems

Alliance Laundry Systems SWTT21 Guide

Alliance Laundry Systems

Alliance Laundry Systems UWL045T3V Owner's manual

Alliance Laundry Systems

Alliance Laundry Systems LTS90A*N User manual

Alliance Laundry Systems

Alliance Laundry Systems LTS97A*N1500 User manual

Alliance Laundry Systems

Alliance Laundry Systems F232139R3 Owner's manual

Alliance Laundry Systems

Alliance Laundry Systems Speed Queen LFNE5B User manual

Alliance Laundry Systems

Alliance Laundry Systems HTE517xE2802 User manual

Alliance Laundry Systems

Alliance Laundry Systems SW039 Owner's manual

Alliance Laundry Systems

Alliance Laundry Systems Dishwasher User manual

Alliance Laundry Systems

Alliance Laundry Systems Commercial Automatic Washer Use and maintenance manual

Alliance Laundry Systems

Alliance Laundry Systems DRY2033N User manual

Alliance Laundry Systems

Alliance Laundry Systems LWS02M series User manual

Alliance Laundry Systems

Alliance Laundry Systems 801455R2 User manual

Alliance Laundry Systems

Alliance Laundry Systems CCN020HNF Owner's manual

Alliance Laundry Systems

Alliance Laundry Systems 1305 Owner's manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide