Airflow Aura-eco Manual

9041411

INSTALLATION & OPERATING INSTRUCTIONS

Aura-eco

100mm & 150mm Axial Fans

Introduction

This Service Instructions are combined with technical specification, operating

guide and specification for the “Aura-eco ” fan; it contains information on

installation, that are important for ensuring correct and safe operation of the fan.

Designation

Fans are designed for ventilation of domestic and similar premises

(apartments,offices,stores,garages,kitchens, bathrooms, toilets and other

rooms, heated in wintertime).

Fans are exhaust fans and are designed for wall or ceiling mounting (Fig.6,7).

They are designed for a long-duration operation, without disconnection from

the power network.

The fan design is being constantly improved therefore some models may

slightly vary from those described in the present specification.

Set of supply

The following article is included:

- Fan 1pc;

- User's manual;

- Screws 4 pcs.

- Packing box

The fan arrangement with the timer or with a timer and a humidity sensor is

shown at the Fig. 1

2 3

Fig.1

1-cover, 2-casing, 3-electric motor

4-blade impeller, 5-timer.

The options arrangement of the fans is given in the table 1.

Table 1

PRT

Adjustable

timer (2-30) minutes



Timer with

humidity sensor



Timer with

motion sensor



Key features

The fans' designation, their characteristics, appearance, overall and

connection dimensions are listed in the tables 2,3 and at the Fig. 1,2.

The fans are designed for the connection to the AC network with the

voltage of 220-240 V and current frequency of 50 Hz.

Table 2

Max.

air intake,

m3/h

Max.

pressure,

Nominal

power,

Noise

level,

dBA

235

The fans are designed for use in the premises with

temperature from 0°C to 45°C.

The fans do not interfere with radio, television and video

equipment.

Table 3

Type

Dimensions,

Weight,

Aura eco-air 100

150

122

102

100

0,56

Aura eco-air 150

205

174

124

150

0,9

Overall and connection dimensions

Fig.

1- Timer with motion sensor

Fig.

SAFETY REQUIREMENTS

The fan “Aura-eco” complies with the requirements according to the EU

norms and directives.

Level of protection from access to hazardous parts and waterproof is to

IPX4

Connection of fans supplied with the electric cords to power supply as well as

replacement of electric cord should be perfomed by a competent person

(Part P) and in accordance with latest IEE wiring regulations. A 3 amp fused

isolator should be fitted.

Fan operation beyond the operational temperature range as well as in rooms

with ambient air containing aggresive mixture is prohibited.

Precautions must be taken to avoid the black -flow of gases into the room

from the open flue of gas or other fuel-burning appliances.

Attention: Ensure impeller rotates freely. Do not overtight on

ductwork connections to fan spigot.

Precautions must be taken to avoid the black -flow gases

into the room from the open flue of gas or other fuel-

burning appliances.

PREPARATION OF DEVICE OPERATION

Attention: All work must be carried out with the equipment fully

isolated from the power supply. The electrical connection

is to be carried out in accordance with the relevant wiring

diagram and are only to be done by a certified electrician.

The electrical connection must be fully isolated from the

supply up to the final assembly!

All relevant safety regulation, national standards and norms are to be adhered

to. An appliance is required for cut off from the supply with a minimum of 3mm

contact opening of each pole.

The rated voltage and frequency must correspond with the data on the type

plate. The insertion of mains supply cable is carried out via a cable grommet

which is included in the delivery. Never lead cable over sharp edges. The

equipment corresponds to protection IPX4.

Diagrams of the connection to electric supply

Diagram of the connection of “Aura-eco” fan

without built-in switch, where B is an external

switch

Diagram of the connection of “Aura-eco” fan

with timer / timer with humidity sensor, with

built-in switch

connection of

“Aura-eco”fan

100/150 B

connection of

“Aura-eco”fan

100/150 T, HT

Diagram of the connection of “Aura-eco”

fan with timer / timer with motion sensor,

without built-in switch

connection of

“Aura-eco”fan

100/150 PRT

USERMAINTENANCE ANDSENSORADJUSTMENT

Before starting work ensure the fan is disconnected from the power

supply.

Cleaning should be done with a soft cloth wet with soap solution; after that, the

surfaces should be rubbed dry. The blades of the fan need careful cleaning

each 6 months. For this purpose, it is necessary to take the blade wheel off the

motor shaft (holding it by the boss). The blades should be cleaned with

solution of water and a detergent. Please avoid water entry on the motor.

Fig. 5.1

The fan with timer options switches on when the voltage is

supplied to clamp LT. After the voltage is disconnected the fan

continues working during the time T, which is regulated from 2

till 30 minutes. The time T is regulated by turning the

potentiometer clockwise to increase and anticlockwise to

decrease the delay time (Fig. 5.1)

The fan with timer and humidity sensor

switches on when voltage is supplied to

clamp LT or when the definite humidity

level ( regulated from 60% till 90 %) is

exceeded. After the voltage is

60%

min

max

90%

extreme

right

position

Fig. 5.2

disconnected or humidity level H is decreased, the fan continues

working during the time set by timer T, which is regulated from

2 till 30 min. The options of time T and humidity H are regulated

by turning the potentiometers T and H clockwise to increase and

anticlockwise to decrease the delay time and humidity level

respectively. To set the maximum humidity level the potentiometer H has to be

set in position H max (90%).

Attention! If during the regulation the potentiometer H is set outside of the

indicated zone rightwards from H max there is a probability that the fan will not

switch on. In this case, it is necessary to check the position of the potentiometer

(Fig. 5.2).

Fig. 5.3

The fan with the timer and movement sensor switches on

when a person moves at the distance from 1 till 4 meters with

viewing angle of the sensor of 100° horizontaly. After the

person stops moving the fan continues working during the set

time T, which is regulated from 2 till 30 minutes. The time T is

regulated by turning the potentiometers clockwise to increase

and anticlockwise to decrease the delay time (Fig. 5.3)

Fig. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Table of contents

Other Airflow Fan manuals

Airflow

Airflow ICONsmart 15 User manual

Airflow

Airflow QT 150HT User manual

Airflow

Airflow AIR 125-R User manual

Airflow

Airflow iCON PCS User manual

Airflow

Airflow iCON Series User manual

Airflow

Airflow Uno hab Manual

Airflow

Airflow 7106A User manual

Airflow

Airflow MV150 PECO User manual

Airflow

Airflow Ceiling fans User manual

Airflow

Airflow DUPLEXVENT DV145SE Owner's manual

Airflow

Airflow QuietAir QT 120T User manual

Airflow

Airflow AV 100 User manual

Airflow

Airflow QuietAir QT 100MST User manual

Airflow

Airflow CE100D User manual

Airflow

Airflow ICONsmart 15 Operating instructions

Airflow

Airflow iCON 30 Installation guide

Airflow

Airflow AIROVENT MEV WH4B Operation manual

Airflow

Airflow Loovent Series User guide

Airflow

Airflow Adroit DV245 Series User manual

Airflow

Airflow Aria 100B Installation guide

Airflow

Airflow iCON Installation guide

Airflow

Airflow Duplexvent Rotary DV1500 User manual

Airflow

Airflow Uno hab Operating manual

Airflow

Airflow Duplexvent Flexi DV1600 User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual