Airflow Aura Smart User manual

INSTALLATION AND OPERATING INSTRUCTIONS

Aura Smart

Innovative Low Energy Axial Fan

80000178 Issue 1-01/14

Disconnect the fan from power mains prior to any connection, servicing and repair operations.

Mounting and maintenance are allowed for duly qualied electricians with valid electrical work permit for electric operations

at the units up to 1000 V after careful study of the present user's manual.

The single-phase power grid must comply with the acting local electrical norms and standards.

The xed electrical wiring must be equipped with an automatic circuit breaker.

The fan must be connected to power mains through an automatic circuit breaker integrated into the xed wiring system

with the gap between the breaker contacts on all poles not less than 3 mm.

Check the fan for any visible damages of the impeller and the casing before starting installation and set-up.

The casing internals must be free of any foreign objects which can damage the impeller blades.

Misuse of the device or any unauthorized modication is not allowed.

The fan is not to be used by children and persons with reduced physical, mental or sensory capacities, without proper

practical experience or expertise, unless they are controlled or instructed on the product operation by the person(s)

responsible for their safety.

Do not leave children unattended and do not let them play with the product.

Take steps to prevent ingress of smoke, carbon monoxide and other combustion products into the room through open

chimney ues or other re-protection devices. Sucient air supply must be provided for proper combustion and exhaust of

gases through the chimney of fuel burning equipment to prevent back drafting.

Transporting medium must not contain any dust or other solid impurities, sticky substances or brous materials.

Do not use the fan in the environment containing hazardous or explosive materials and vapours, i.e. spirits, gasoline,

insecticides, etc. Do not close or block the fan intake or extract vents in order to ensure the most eective air passage.

Do not sit on the fan and do not put objects on the fan.

Fulll the requirements stated in this user's manual to ensure long service life of the product.

WARNING

Thank you for purchasing this fan from Airow Developments. Aura Smart is an innovative extract bathroom fan enclosed into a

compact casing. The unique technologies combined with smart electronics support the ideal comfort and

microclimate in your house. The stylish fan design matches well with any modern interior.

We do hope that you are happy with your fan's performance quality.

Read the present user's manual carefully before proceeding with installation works.

Compliance with the manual requirements ensures reliable operation and long service life of the product.

Keep the user's manual available as long as you use the product. You may need to re-read the information on the

product servicing.

DELIVERY SET

The delivery set includes:

1. Fan - 1 pce;

2. Logo - 1 pce;

3. Remote controller - 1 pce;

4. Spigot Ø100 mm - 1 pce;

5. Spigot Ø125 mm - 1 pce;

6. Screws and dowels - 4 pcs;

7. User's manual - 1 pce.

DESCRIPTION

Due to constant improvements the design of some models may slightly differ from that one described in this manual.

The product described herein is the axial fan made of high-quality plastic designed for extract ventilation of small and

medium-sized residential premises that are heated during winter period.

Table 1

Recycle at the end of the service life.

Do not dispose the product with unsorted municipal trash.

WARNING

Voltage [V]

Frequency [Hz]

Max. power [W]

Current [A]

-1

RPM [min ]

Max. air capacity [m /h]

Ingress Protection

Weight [kg]

100-240

50-60

0,03

133

IP 44

0,35

3,8

2200

Table 2

Table 3

Overall dimensions

The fan has four ventilation modes:

1. Standby mode -standard operation mode for the fan in case of no signalling from the sensors or external switch.

In standby mode the fan does not run.

2. 24 Hours -the fan runs at low speed for minimum round-the-clock ventilation. As humidity level increases, the fan switches

to MAX mode (by default) or to SILENT mode. The fan switches to SILENT mode when the motion sensor is activated or

external switch is closed.

3. SILENT -silent operation mode of the fan. This mode is may be activated by the motion sensor, external switch or humidity

sensor. For humidity sensor, this mode may be activated from the fan.

4. MAX -humidity-activated operation mode. It is switched on as humidity level increases.

This mode is activated for the humidity sensor by default.

Aura Smart HT/

MSHT

100

24 Hours 33 17

Aura Smart MSHT +

Aura Smart HT

152

206

29 28

100/125

Silent 72 22

Max 106 31

125

24 Hours 40 17

Silent 83 21

Max 133 32

33 ... 72

72 ... 106

40 ... 83

83 ... 133

Model Speed

Spigot

dia.

Noise level at 3m

[dBA]

Max. air capacity

[m /h]

Functions

Humidity

control 24 Hour Speed

control

Interval

ventilation

External

switch

Motion

sensor

O-delay

timer

Turn-on

delay timer

Air capacity,

factory settings [m /h]

Air capacity

regulation range [m /h]

Model Pause

PRODUCT MOUNTING

The fan is designed for mounting into round

Ø100 or 125 mm air duct or installation into

the ventilation shaft.

The replaceable adapter of required size may be

used to facilitate mounting.

The fan is equipped with a removable grille.

Press the latches slightly to release the grille from the

front cover. While installing the grille on the front cover

back match the latches and respective slots in the

cover and insert to click.

The pointer on the reverse side of the grille must be

directed to the shorter side close to the hole.

100

125

QFQF

The fan casing has three round lowered tabs for cable entry.

Cut out a hole at the most suitable place with a knife.

FAN MOUNTING SEQUENCE

4 5 6

1 2 3

7 8 9

10 11 12

The fan may be connected to power mains by four wiring diagrams.

The fan is compatible with 100-240 V / 50-60 Hz power mains.

The Aura Smart MSHT has Li terminal for connection to the lamp up to 200W/230 V or 100 W/120 V.

At this connection the fan will be switched on signal from the motion sensor.

Wiring diagram 1

L and N terminals are connected to live and neutral respectively. The fan is always in standby mode and does not run.

As 24 HOURS Mode is activated the fan runs permanently at low speed to ensure minimum round-the-clock ventilation.

As motion sensor is activated (for iFAN Move only) the fan switches to SILENT mode. After no motion is detected the fan

reverts to standby mode. As humidity level increases the fan switches to MAX mode (by default) or to SILENT mode.

After humidity level drops the fan reverts to standby mode.

LILI

LTLT

Standby mode

(fan does not run)

24 Hours mode

(fan operated at 40/33 m /h)

Turn-on delay

timer starts

(0-2-5 min)

Humidity

change

Motion sensor

is activated

MAX (SILENT)

mode is activated

Fan operation in

Silent mode

Signal to LIterminal

(light is off)

Humidity

stabilization

Motion

if off

Signal to LI terminal

(light is on)

Humidity extraction

timer starts

(30-45-60 min)

Turn-off delay

timer starts

(5-15-30 min)

Turn-on delay

timer starts

(0-2-5 min)

Wiring diagram 2

L and N terminals are connected to live and neutral respectively and L and LT terminals are joined by the jumper.

The fan is always in SILENT mode. 24 Hours mode may not be activated. No matter of the signal from the motion sensor

the fan operated in SILENT mode. As humidity level increases the fan switches to MAX mode (by default) or continues

operation in SILENT mode (if adjusted by the user). After humidity level drops to standard level the fan reverts to SILENT mode.

LILI

LTLT

Fan operates

83/72 m /h (MAX)

40/33 m /h (MAX)

at air flow:

Humidity

change Motion sensor

is activated

MAX (SILENT)

mode is activated

Fan operation in

Silent mode

Humidity

stabilization

Motion

if off

Signal to LIterminal

(light is on)

Humidity extraction

timer starts

(30-45-60 min)

Turn-off delay

timer starts

(5-15-30 min)

Signal to LIterminal

(light is off)

Turn-on delay

timer starts

(0-2-5 min)

Turn-on delay

timer starts

(0-2-5 min)

Wiring diagram 3

L and N terminals are connected to live and neutral respectively. LT contact is connected to live through external switch,

light switch. The fan is always in standby mode. As 24 HOURS Mode is activated the fan runs permanently at low speed to

ensure minimum round-the-clock ventilation. As the external switch is closed the fan switches to SILENT mode.

After the external switch is o the fan reverts to standby mode. As motion sensor is activated (for Aura Smart MSHT only) the fan

switches to SILENT mode. After no motion is detected the fan reverts to standby mode. As humidity level increases the fan

switches to MAX mode (by default) or to SILENT mode. After humidity level drops the fan reverts to standby mode.

Standby mode

(fan does not run)

24 Hours mode

(Fan operates at 40-33 m /h)

Humidity

change Motion sensor

is activated

MAX (SILENT)

mode is activated

Fan operation in

Silent mode

Humidity

stabilization

Motion

if o

Signal to L I terminal

(light is on)

Humidity extraction

timer starts

(30-45-60 min)

Turn-o  delay

timer starts

(5-15-30 min)

Switch is

closed

Turn-on delay

timer starts

(0-2-5 min)

Turn-on delay

timer starts

(0-2-5 min)

Signal to L I terminal

(light is o)

Switch

is o

Switch

is o

Table of contents

Other Airflow Fan manuals

Airflow

Airflow Ceiling fans User manual

Airflow

Airflow Aventa AV100B Installation guide

Airflow

Airflow iCON eco15 Installation guide

Airflow

Airflow Duplexvent Rotary DV1500 User manual

Airflow

Airflow AIROVENT MEV WH4H CENTRAL EXTRACT User manual

Airflow

Airflow 90001265 Operating manual

Airflow

Airflow AV125T User manual

Airflow

Airflow LA HABRA User manual

Airflow

Airflow QuietAir User guide

Airflow

Airflow 72687117 Installation guide

Airflow

Airflow Aria 100B Installation guide

Airflow

Airflow Duplexvent MULTI-N User manual

Airflow

Airflow iCON Installation guide

Airflow

Airflow ACES48ALR User manual

Airflow

Airflow Adroit DV245 Series User manual

Airflow

Airflow iCON 15S Installation guide

Airflow

Airflow 7006A User manual

Airflow

Airflow DUPLEXVENT DV145SE Owner's manual

Airflow

Airflow Loovent Series User guide

Airflow

Airflow iCONstant T User manual

Airflow

Airflow iCON Series User manual

Airflow

Airflow QuietAir QT 100MST User manual

Airflow

Airflow Uno hab User manual

Airflow

Airflow iCON 30 Installation guide

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual