Agilent Technologies U1610/20A User manual

Agilent Technologies

Verify that you received the following items in the shipment of

your handheld scope:

✔1 × Power cable

✔1 × Li-Ion battery pack, 10.8 V (included in the handheld

scope)

✔1 × AC/DC adapter

✔2 × 10:1 CAT III 600 V scope probe

✔1 × BNC-to-probe adapter

✔1 × DMM (digital multimeter) test lead kit

✔1 × USB cable

✔1 × Hand strap (attached on the handheld scope)

✔1 × Neck strap

✔Printed Quick Start Guide

✔Certificate of Calibration

If anything is missing or damaged, contact the nearest Agilent

Sales Office.

NOTE

All related documents and software are available for download

at www.agilent.com/find/hhTechLib.

Quick Start Guide

Agilent U1610/20A

Handheld Digital

Oscilloscope

U1610/20A Handheld Digital Oscilloscope

2 U1610/20A Quick Start Guide

Charge the Battery

Before using the handheld scope for the first time, fully charge

the battery for at least 5 hours, with the handheld scope turned

off, using the AC/DC adapter provided.

The power key will turn constant yellow when the battery

is fully charged.

Power On the Handheld Scope

Press and hold for approximately 1.5 seconds. When the

handheld scope display appears, the handheld scope is ready

for use.

NOTE

Hook up all cables and accessories before applying power. You

can connect/disconnect probes while the handheld scope is

turned on.

U1610/20A Handheld Digital Oscilloscope

U1610/20A Quick Start Guide 3

Product Outlook

Scope terminals

Display screen

Function softkeys

To perform the func-

tion displayed above

each softkey.

Acquisition and func-

tion controls

To access the scope,

meter, logger, system,

and help functions.

Vertical controls

To set the vertical

scaling (volt/div)

and vertical offset.

Power key

USB interface

connector and

DC power inlet

Directional keys

Horizontal controls

To control the sweep speed (sec/div)

and horizontal position of the wave-

form. Use

to zoom into the waveform.

Meter terminals

U1610/20A Handheld Digital Oscilloscope

4 U1610/20A Quick Start Guide

Oscilloscope Display

Multimeter Display

Logger Display

1Displays the

channel and

timebase setup

information.

2Displays the

channel input

waveforms.

3Displays the

sample rate.

4Displays the

key/softkey

function menus.

5Displays the signal

acquisition mode.

6Displays the

battery status and

AC connectivity for

battery charging.

7Displays the signal

triggering status.

8Displays the date

and time.

9Displays the

acquisition, start

date and time, and

duration status.

10 Displays the

measurement.

11 Displays the virtual

measurement

scale.

12 Displays the

average,

maximum, and

minimum values.

13 Indicates the auto

or manual ranging

mode.

14 Displays the

logging graph.

1 5

U1610/20A Handheld Digital Oscilloscope

U1610/20A Quick Start Guide 5

Set the Date and Time

Press > > . Press any

softkey and use the or key to change the values.

Set the Language

Press > > and use

the keys to select the language.

Press again to exit the selection menu.

Connect Probes to Oscilloscope Terminals

NOTE

is only accessible when in the Scope mode.

U1610/20A Handheld Digital Oscilloscope

6 U1610/20A Quick Start Guide

Reset the Oscilloscope

Press > .

Connect Test Leads to Meter Terminals

NOTE

Before resetting to factory default settings, you may want to

save the current handheld scope configuration for later use by

pressing > .

NOTE

For details on using the oscilloscope functions, see the

User’s Guide.

U1610/20A Handheld Digital Oscilloscope

U1610/20A Quick Start Guide 7

Meter Measurements

To access the multimeter mode, press .

Measurement functions

Function Relative Range Restart Test MaxMinAvg

V AC ✔✔ ✔ ✔

V DC ✔✔ ✔ ✔

V AC+DC ✔✔ ✔ ✔

Resistance ✔✔ ✔ ✔

Capacitance ✔✔ ✔ ✔

Diode Test ✔-✔✔

Continuity ✔✔ ✔ ✔

Frequency ✔✔[1]

[1] Frequency measurement works in the autorange mode, and the

range that you select applies for V AC.

✔✔

°C ✔-✔✔

°F ✔-✔✔

NOTE

For details on using the meter functions, see the User’s Guide.

U1610/20A Handheld Digital Oscilloscope

8 U1610/20A Quick Start Guide

Data Logging

The data logger acts as a recorder to log and plot input signal

trends for both scope and meter measurements.

To access the logger mode, press .

Access the Quick Help

Press any function key/softkey followed by to

display its respective Help information. Use the keys to

navigate within Help.

NOTE

For details on using the logger functions, see the User’s Guide.

NOTE

To view Help in another language, press >

> and use the keys.

Press again to exit the selection menu.

NOTE

To access information on using Help, press and hold

for approximately 3 seconds.

Contacting Agilent

To obtain service, warranty, or technical assistance, contact us at the following phone

numbers:

•United States Call Center: 800-829-4444

•Canada Call Center: 877-894-4414

•China Call Center: 800-810-0189

•Europe Call Center: 31-20-547-2111

•Japan Call Center: (81) 426-56-7832

For other countries, contact your country’s Agilent support organization. A list of con-

tact information for other countries is available on the Agilent Web site:

www.agilent.com/find/assist

Safety Notices Safety Information

This handheld scope is certified to the fol-

lowing safety and EMC requirements.

•IEC 61010-1:2001/EN 61010-1:2001

•Canada: CAN/CSA-C22.2 No. 61010-1-04

•USA: ANSI/UL 61010-1:2004

•IEC 61326-1:2005/EN 61326-1:2006

•Australia/New Zealand: AS/NZS CISPR

11:2004

•Canada: ICES/NMB-001: ISSUE 4,

June 2006

Use with compatible test probe/leads.

Safety Symbols

CAUTIONCAUTION

A CAUTION notice denotes

a hazard. It calls attention

to an operating procedure,

practice, or the like that, if

not correctly performed or

adhered to, could result in

damage to the product or

loss of important data. Do

not proceed beyond a CAU-

TION notice until the indi-

cated conditions are fully

understood and met.

WARNING

A WARNING notice

denotes a hazard. It calls

attention to an operating

procedure, practice, or the

like that, if not correctly

performed or adhered to,

could result in personal

injury or death. Do not pro-

ceed beyond a WARNING

notice until the indicated

conditions are fully under-

stood and met.

Direct current

(DC) Alternating

current (AC)

Both direct and

alternating cur-

rent

Earth

(ground) ter-

minal

Caution, risk of

danger (refer to

the instrument

manual for spe-

cific Warning or

Caution infor-

mation)

Equipment

protected

throughout

by double

insulation or

reinforced

insulation

Caution, risk of

electric shock

Category II

overvoltage

protection

Category III

overvoltage

protection

CAT II

CAT III

For further safety information details, refer to the

Agilent U1610/20A Handheld Digital Oscilloscope User’s Guide.

Agilent Technologies

Assurez-vous d’avoir reçu les articles suivants avec la livraison

de votre oscilloscope portable :

✔1 × cordon d’alimentation

✔1 × pile lithium, 10,8 V (incluse dans l’oscilloscope

portable)

✔1 × adaptateur secteur

✔2 × sonde 10:1 CAT III 600 V

✔1 × adaptateur BNC-sonde

✔1 × kit cordon de test du DMM (multimètre numérique)

✔1 × câble USB

✔1 × poignée (attachée à l’oscilloscope portable)

✔1 × sangle tour de cou

✔Guide de mise en route imprimé de l’instrument

✔Certificat d’étalonnage

Si un composant est absent ou endommagé, contactez votre

distributeur Agilentle plus proche.

REMARQUE

Tous les documents et logiciels associés peuvent être

téléchargés depuis le site www.agilent.com/find/hhTechLib.

Guide de mise en route

Agilent U1610/20A

Oscilloscope numérique

portable

Table of contents

Languages:

Other Agilent Technologies Test Equipment manuals

Agilent Technologies

Agilent Technologies U1401A User manual

Agilent Technologies

Agilent Technologies 85105A Option 50 Installation and operation manual

Agilent Technologies

Agilent Technologies 85057B Manual

Agilent Technologies

Agilent Technologies 54831A User manual

Agilent Technologies

Agilent Technologies 85052C Manual

Agilent Technologies

Agilent Technologies J-BERT N4903B User manual

Agilent Technologies

Agilent Technologies 4072A Advanced User manual

Agilent Technologies

Agilent Technologies 8922 User manual

Agilent Technologies

Agilent Technologies E7495A RF Instruction Manual

Agilent Technologies

Agilent Technologies E5515BU-863 Installation and operation manual

Agilent Technologies

Agilent Technologies Infinium DCA 86100A User manual

Agilent Technologies

Agilent Technologies HP 10070A User manual

Agilent Technologies

Agilent Technologies 8924C Service manual

Agilent Technologies

Agilent Technologies Medalist x6000 User manual

Agilent Technologies

Agilent Technologies InfiniiVision 3000 X-Series Manual

Agilent Technologies

Agilent Technologies E6392B User manual

Agilent Technologies

Agilent Technologies E7490A User manual

Agilent Technologies

Agilent Technologies 16197A Operation manual

Agilent Technologies

Agilent Technologies 16194A Operation manual

Agilent Technologies

Agilent Technologies 16034E Operation manual

Agilent Technologies

Agilent Technologies 16452A Operation manual

Agilent Technologies

Agilent Technologies 2000 X-Series User manual

Agilent Technologies

Agilent Technologies 3000 Series User manual

Agilent Technologies

Agilent Technologies 4072A Advanced User manual

Popular Test Equipment manuals by other brands

SMART

SMART KANAAD SBT XTREME 3G Series user manual

Vernier

Vernier Go Direct Voltage manual

Lifeloc

Lifeloc R.A.D.A.R. quick start guide

Fluke

Fluke T5-600 Service information

Mercury

Mercury TSL01 user manual

MAHA

MAHA MBT Series Original operating instructions

Fuji Electric

Fuji Electric P-61 instruction manual

ETC

ETC SealerAtor user manual

Skyfine

Skyfine ETHYWAY V2 user manual

Appion

Appion G5 Twin Operation manual

PCB Piezotronics

PCB Piezotronics 8159-0112A Installation and operating manual

BW Technologies

BW Technologies MicroDock II user manual

Sun Nuclear

Sun Nuclear 1027 user guide

Biomark

Biomark HPR LITE READER user manual

Hioki

Hioki 3169-20 instruction manual

Ashcroft

Ashcroft ATE-100 operating manual

Rohde & Schwarz

Rohde & Schwarz RTA4000 user manual

Ritmix

Ritmix RAT-701 user manual