Agilent Technologies ESG-D Series Quick start guide

Part Number E4400-90214

Printed in USA October 2004

Supersedes July 2000

Installation Note

Agilent Technologies ESG-D and ESG-DP Series

Signal Generators Option UND Upgrade

Kit Part Numbers E4400-60166 and E4400-60181

Models: E4430B, E4431B, E4432B, E4433B, E4434B,

E4435B, E4436B and E4437B

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited

to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies

shall notbe liable for errors contained herein or for incidental orconsequential damages in connection with

the furnishing, performance, or use of this material.

Installation Note E4400-90214 3

Standard ESG-D to Option UND Upgrade Kit

Introduction

This installation note contains instructions for installing Option UND, the dual arbitrary waveform

generator, in a standard ESG-D or ESG-DP signal generator. This note applies to two kits. The kit used

is determined by the options installed. The kits are identified and described below.

Perform this installation in its entirety and in the order presented.

Product Affected: . . . . . . . . . . . . . . . . . . . . . . . . . ESG-D and ESG-DP Series Signal Generators

Models Affected: . . . . . . . . . . . . . . . . . . . . . . . . . . . E4430B, E4431B, E4432B, E4433B, E4434B,

E4435B, E4436B and E4437B

Serial Numbers: . . . . . . . . . . . . . . . . . . . . . . . . . . . All

To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Service Center

(X) Personnel Qualified by Agilent Technologies

(X) Customer

Estimated Installation Time: . . . . . . . . . . . . . . . . 1.5 hours

Estimated Verification Time: . . . . . . . . . . . . . . . . . 0.5 hour

Kit Part Number Description

E4400-60166 Installs Option UND in signal generators

without Options UN3/4 or UN8/9 installed.

E4400-60181 Installs Options UND in signal generators

equipped with Option UN3/4 or UN8/9.

4 Installation Note E4400-90214

Upgrade Kit E4400-60166

(For Signal Generators without Options UN3/4 or UN8/9)

The tools and kit contents required to install the Option UND upgrade for signal generators not

equipped with Options UN3/4 or UN8/9 are described below.

Tools Required

❏T-10 TORX screwdriver

❏T-15 TORX screwdriver

❏Break away torque wrench, 9 in-lbs

❏Ratchet, 21 in-lbs

❏Socket, 9/16

❏Socket, 3/8

❏Hand torque driver, 9 in-lbs, socket 9/32

❏Hand torque driver, 6 in-lbs, socket 3/16

❏Scissors

WARNING Before you disassemble the signal generator, turn the power switch off

and disconnect the line cord. Failure to unplug the signal generator can

result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Installation Note E4400-90214 5

Upgrade Kit E4400-60166 Contents

Item

Quantity

Description Part

Number

Std(No

Opt’sa)

a Implies no other digital hardware installed.

UN7

1 1 0 This installation note E4400-90214

2 1 1 Dual arbitrary waveform generator board E4400-60187

3 1 0 Rear-panel interface board E4400-60145

4 1 0 Rear panel (Option UND) E4400-00031

5 1 0 W3, DATA to motherboard or

DATA to Data Generator (A8J2) (Option UN3/4 or UN8/9) 8120-5063

6 1 0 W4, DATA CLOCK to motherboard or

DATA CLOCK to Data Generator (A8J1) (Option UN3/4 or UN8/9) 8120-5063

7 1 0 W5, SYMBOL SYNC to motherboard or

SYMBOL SYNC to Data Generator (A8J3) (Option UN3/4 or UN8/9) 8120-5063

8 1 0 W15, dual arbitrary waveform generator (A5J3) to BASEBAND

GEN REF IN (13 MHz) 8120-5055

9 1 0 W16, dual arbitrary waveform generator (A5J2) to Q OUT 8120-5055

10 1 0 W17, dual arbitrary waveform generator (A5J1) to I OUT 8120-5055

11 1 0 W18, rear-panel interface board (A17) to dual arbitrary waveform

generator (A5P1) ribbon cable 8120-8458

12 1 1 W24, for future use with Options UND and UN3/4 or

Options UND and UN8/9 E4400-20131

13 11 0 Washer, lock 0.4721D 2190-0102

14 3 0 Washer, lock 0.4091D 3050-1919

15 14 0 Nut, hex 15/32-32 2950-0035

16 3 0 Plug, hole 0.500D 6960-0002

17 1 0 Label, Option UND serial number 7120-1232

18 1 0 Label, front-panel overlay-connectors (Option UND) E4400-80006

19 1 0 Safety solvent cleaner 8500-6269

20 1 0 Firmware Upgrade Kit E4400-60230

21 1 0 W25, INT Q coax cable A14P103 to Daughter board A15J8 8120-8748

22 1 0 W26, INT I coax cable A14P102 to Daughter board A15J9 8120-8748

23b

b For ESG-DP Models E4434B, E4435B, E4436B and E4437B.

1 0 W25, INT Q coax cable A14P103 to Daughter board A15J8 8120-8781

24b10 W26, INT I coax cable A14P102 to Daughter board A15J9 8120-8781

6 Installation Note E4400-90214

Upgrade Kit E4400-60181

(For Signal Generators Equipped with Options UN3/4 or UN8/9)

The tools and kit contents required to install the Option UND upgrade for signal generators equipped

with Options UN3/4 or UN8/9 are described below.

Tools Required

❏T-10 TORX screwdriver

❏T-15 TORX screwdriver

❏Scissors

WARNING Before you disassemble the signal generator, turn the power switch off

and disconnect the line cord. Failure to unplug the signal generator can

result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Upgrade Kit E4400-60181 Contents

Item

Quantity

Description Part

Number

Std(No

Opt’s) UN7 UN3/4

UN8/9

1 1 0 0 This installation note E4400-90214

2 1 1 1 Dual arbitrary waveform generator board E4400-60187

3 1 1 1 W24, baseband generator-13 MHz (A7J3) to dual arbitrary

waveform generator-13 MHz (A5J4) E4400-20131

4 1 0 0 Label, Option UND serial number 7120-1232

5 1 0 0 Firmware Upgrade Kit E4400-60230

6 1 0 0 W25, INT Q coax cable A14P103 to Daughter board A15J8 8120-8748

7 1 0 0 W26, INT I coax cable A14P102 to Daughter board A15J9 8120-8748

a For ESG-DP Models E4434B, E4435B, E4436B and E4437B.

1 0 0 W25, INT Q coax cable A14P103 to Daughter board A15J8 8120-8781

9a1 0 0 W26, INT I coax cable A14P102 to Daughter board A15J9 8120-8781

Installation Note E4400-90214 7

Functionality Check

This procedure verifies that the signal generator powers up and that the internal instrument check

does not identify any errors. The internal check returns an error message if a problem is detected.

1. Turn the signal generator’s power switch on. The green LED will light. Let the signal generator

warm up for 5 minutes.

2. Cycle the power to the signal generator. The green LED lights again and the signal generator

performs a check.

3. When the display is illuminated, check to see if the ERR annunciator is displayed.

NOTE For signal generators with Option 1E5, ERROR 514,Reference Oven Cold will

occur whenever the signal generator is first connected to the AC line power. This

error cannot be cleared from the error queue until the internal reference has

warmed up (approximately 5 minutes).

4. If the ERR annunciator is displayed, review the error messages in the queue by pressing Utility >

Error Info. The first error message in the queue will be shown in the text area of the display. Refer to

the service guide for information about the error message.

If there is more than one error message (each message will be designated as 1 of n, 2 of n, etc.),

continue pressing the View Next Error Message softkey until you have seen all of the messages.

5. When you have resolved all of the error messages, press ClearErrorQueue(s)to delete the messages,

then restart this procedure at step two.

8 Installation Note E4400-90214

Installation Procedure

Remove the signal generator covers

1. Turn the signal generator’s power switch off and disconnect the line cord.

2. Refer to Figure 1 on page 8. Remove the four bottom feet (item 3).

3. Remove the two strap handles (item 1) from each side of the signal generator by loosening the two

screws (item 2) on each handle.

4. Remove the four rear feet (item 4) from the signal generator by removing the four screws (item 5)

that secure them.

5. Slide the signal generator top cover (item 6) off the back of the signal generator.

6. Refer to Figure 2 on page 9. Remove the 11 screws (item 1) that secure the top chassis cover (item 2)

and remove it.

7. If Options UN3/4 or UN8/9 are installed, proceed to “Install the Option UND Board Assembly

(Options UN3/4 or UN8/9 Installed)” on page 17.

Figure 1 Top Cover Removal

Installation Note E4400-90214 9

Figure 2 Top Chassis Cover Removal

Remove the Standard Signal Generator Rear Panel

1. Refer to Figure 3 on page 10. Remove the 15 screws (item 2) that secure the bottom chassis cover

(item 3) and lift the chassis cover off.

2. Refer to Figure 4 on page 11. Disconnect A16W1 from the power supply (A4). Access to A16W1 can

be gained through an opening in the bottom of the power supply shield (item 1, Figure 3).

10 Installation Note E4400-90214

Figure 3 Bottom Chassis Cover Removal

3. Refer to Figure 4 on page 11. Remove the nuts and washers that secure the five BNC connectors

(item 2).

4. Remove the hex screws and washers that secure the AUXILIARY INTERFACE (item 3) and GPIB

(item 4) connectors to the rear panel.

5. Remove the 10 screws (item 5) that secure the rear panel to the signal generator chassis.

6. Remove the two screws and the bracket from top of the rear chassis. Save the bracket.

7. Disconnect the COHERENT CARRIER CABLE (W12) from the rear panel.

8. Pull the rear panel assembly away from the signal generator chassis.

Other manuals for ESG-D Series

This manual suits for next models

Table of contents

Other Agilent Technologies Portable Generator manuals

Agilent Technologies

Agilent Technologies ESG-D Series User manual

Agilent Technologies

Agilent Technologies E4438C User manual

Agilent Technologies

Agilent Technologies N4971A User manual

Agilent Technologies

Agilent Technologies E4430B Installation and operation manual

Agilent Technologies

Agilent Technologies E8311A User manual

Agilent Technologies

Agilent Technologies HP 81130A User manual

Agilent Technologies

Agilent Technologies E4438C Installation and operation manual

Agilent Technologies

Agilent Technologies E4400B User manual

Agilent Technologies

Agilent Technologies HP 83711A User manual

Agilent Technologies

Agilent Technologies E8663B User manual

Agilent Technologies

Agilent Technologies ESG series User manual

Agilent Technologies

Agilent Technologies E8663B User manual

Agilent Technologies

Agilent Technologies E8267C User manual

Agilent Technologies

Agilent Technologies E4438CK-601 Installation and operation manual

Agilent Technologies

Agilent Technologies N5161A User manual

Agilent Technologies

Agilent Technologies N5161A User manual

Agilent Technologies

Agilent Technologies 33120A User manual

Agilent Technologies

Agilent Technologies ESG-D Series Configuration guide

Agilent Technologies

Agilent Technologies 8340B User manual

Agilent Technologies

Agilent Technologies E8257C User manual

Agilent Technologies

Agilent Technologies E8257D Manual

Agilent Technologies

Agilent Technologies 81141A Series User manual

Agilent Technologies

Agilent Technologies 33210A User manual

Agilent Technologies

Agilent Technologies E4428C User manual

Popular Portable Generator manuals by other brands

Kohler

Kohler 20EORZ Operation

Powerhorse

Powerhorse 83171 owner's manual

HURST

HURST ML-630-SI instruction manual

ETQ

ETQ TG4000 owner's manual

Briggs & Stratton

Briggs & Stratton 40265 Illustrated parts list

ConMed

ConMed 7550 Service manual

Owon

Owon Waveform Generator manual

evertz

evertz 7700 Series manual

Power Stroke

Power Stroke PS906025 Operator's manual

Firefly

Firefly Cygnus CYG2400/460/24 user manual

Draper

Draper PG950S Instructions for

PowerBoss

PowerBoss PowerBoss Operator's manual

SDMO

SDMO SH 4000 Generating set user and maintenance manual

EINHELL

EINHELL STE 5500 operating instructions

Wanco

Wanco WI3000P Operator's manual

Full Boar

Full Boar FBT-3300 instruction manual

Dwyer Instruments

Dwyer Instruments ASG manual

Westinghouse

Westinghouse WH1000i Series owner's manual