Agilent Technologies ESG series User manual
Part Number E4400-90388
Printed in USA September 2000 Supersedes: July 2000
Installation Note
Agilent Technologies ESG Series Signal Generators
(A Models) CPU/Motherboard (Q501 relocated to Chassis)
Replacement Kit: Part Number E4400-60238
Notice
The information contained in this document is subject to change without notice.
Agilent Technologies makes no warranty of any kind with regard to this material, including but not limited
to, the implied warranties of merchantability and fitness for a particular purpose. Agilent Technologies
shall notbe liable for errors contained herein or for incidental orconsequential damages in connection with
the furnishing, performance, or use of this material.
© Copyright 2000 Agilent Technologies, Inc.
Installation Note E4400-90388 3
ESG Series Signal Generators: Part Number E4400-60238
Introduction
This kit enables you to install a replacement CPU/Motherboard and relocate Q501 onto the signal
generator instrument chassis. The relocation of Q501 to the signal generator chassis eliminates the
mechanical stress on this component. You will perform the following major steps:
•check instrument functionality
• disassemble the instrument - external shell, rear panel, PC boards and cables
• remove Q501 and the CPU/Motherboard
• install the new CPU/Motherboard
• install Q501 onto the signal generator’s chassis
• connect Q501 to the CPU/Motherboard
• reassemble, verify, and calibrate the signal generator
Installation Kit Parts List
Product Affected:. . . . . . . . . . . . . . . . . . . . . . . . . . Agilent E4400A, E4420A, E4421A, E4422A, E4430A, E4431A, E4432A
and E4433A Series Signal Generators.
Serial Numbers: . . . . . .. . . . . . . . . . . . . . . . . . . . . All
Options: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . All
To Be Performed By: . . . . . . . . . . . . . . . . . . . . . . . (X) Agilent Technologies Service Center
( ) Personnel Qualified by Agilent Technologies
( ) Customer
Estimated Installation Time: . . . . . . . . . . . . . . . . . 2 hours
Estimated Verification Time: . . . . . . . . . . . . . . . . 8 hours
Item Quantity Description Part Number
1 1 CPU/Motherboard E4400-600011
1Not available as a stand-alone
2 1 Q501 Assembly E4400-60221
3 1 Q501 Plate with PEM E4400-00040
4 1 Q501 Plate without PEM E4400-00041
5 1 Insulator Bushing 0340-1162
6 1 Screw 3MMX10 0515-0374
7 1 Installation Note E4400-90388
4 Installation Note E4400-90388
Tools Required
❏Ratchet 21 in-lb
❏Hand Torque Driver 9 in-lb
❏Hand Torque Driver 6 in-lb
❏Torxdriver T-10
❏Torxdriver T-15
❏5/8 Socket
❏3/16 Socket
❏9/32 Socket
Safety Considerations
WARNING Before you disassemble the instrument, turn the power switch off and
disconnect the line cord. Failure to unplug the Signal Generator can
result in personal injury.
CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All
work on electronic assemblies should be performed at a static-safe workstation.
Installation Note E4400-90388 5
Check Instrument Functionality
The functionality check verifies that the signal generator powers up and that the internal instrument
check identifies no errors. The internal check returns an error message if a problem is detected.
1. Turn on power to the signal generator. Let the instrument warm up for at least five minutes.
2. Cycle the power to the signal generator. The green LED should light, and the instrument will
perform a check.
3. When the display illuminates, check to see if the ERR annunciator is on.
NOTE For instruments with Option 1E5, the error message ERROR 514, Reference Oven Cold
occurs whenever the signal generator is first connected to the AC line power. This error cannot
be cleared from the error queue until the internal reference has warmed up (approximately five
minutes).
4. If the ERR annunciator is displayed, review the error messages in the queue by pressing Utility >
Error Info. The first error message in the queue will be shown in the text area of the display. Refer to
the service guide for information about the error message.
If there is more than one error message (each message will be designated as 1 of n, 2 of n, etc.),
continue pressing the View Next Error Message softkey until you have seen all of the messages.
5. When you have resolved all of the error messages, press ClearErrorQueue(s)to delete the messages,
then restart this procedure at step 2.
6 Installation Note E4400-90388
Remove the Signal Generator Covers
1. Turn the signal generator’s power switch off and disconnect the line cord.
2. Refer to Figure 1. Remove the two strap handles (item 1) from each side of the signal generator by
loosening the two handle screws (item 2).
3. Remove the four bottom feet (item 3).
4. Remove the four rear feet (item 4) from the signal generator by removing the four screws (item 5)
that secure them.
5. Slide the signal generator cover (item 6) off the back of the signal generator.
Figure 1 Instrument Cover and Associated Parts
Installation Note E4400-90388 7
6. Refer to Figure 2. Remove the top chassis cover (item 2) by removing the 11 screws (item 1) that
secure it.
Figure 2 Top Chassis Cover Removal
8 Installation Note E4400-90388
7. Refer to Figure 3. Turn the signal generator over and remove the bottom chassis cover (item 3) by
removing the 15 bottom chassis cover screws (item 2).
Figure 3 Bottom Chassis Cover Removal
Installation Note E4400-90388 9
Removing the Rear Panel
1. Refer to Figure 4. Remove the nuts and washers securing the five BNC connectors (item 1) at the
base of the rear panel.
2. Remove the hex screws and washers that secure the AUXILIARY INTERFACE (item 2) and GPIB
connectors (item 3) to the rear panel.
3. Remove the 10 screws (item 4) that secure the rear panel to the signal generator chassis.
4. Pull the rear panel assembly away from the signal generator chassis.
Figure 4 Rear Panel View
10 Installation Note E4400-90388
Remove the PC Boards and Cables
1. Refer to Figure 5. If the signal generator has Option 1EH, remove the Baseband Generator board
(A7).
2. If the signal generator has Option UN3/4, remove the Baseband Generator board (A7) and the
Pattern Ram board (A8).
Figure 5 Instrument’s Top View
Remove the CPU/Motherboard
1. Refer to Figure 5. Disconnect A1W1, A3W1, B1W1, and B2W1 from the CPU/Motherboard (A14).
2. Disconnect W13 and A4W1 from the CPU/Motherboard (A14).
Other manuals for ESG series
5
This manual suits for next models
7
Table of contents
Other Agilent Technologies Portable Generator manuals
Agilent Technologies
Agilent Technologies E4438C Installation and operation manual
Agilent Technologies
Agilent Technologies E8267C User manual
Agilent Technologies
Agilent Technologies E4428C User manual
Agilent Technologies
Agilent Technologies HP 83711A User manual
Agilent Technologies
Agilent Technologies n5181a Installation manual
Agilent Technologies
Agilent Technologies E8663B User manual
Agilent Technologies
Agilent Technologies E4438CK-601 Installation and operation manual
Agilent Technologies
Agilent Technologies V2920A User manual
Agilent Technologies
Agilent Technologies X Series User manual
Agilent Technologies
Agilent Technologies E4400B User manual
Agilent Technologies
Agilent Technologies ESG-D Series Quick start guide
Agilent Technologies
Agilent Technologies n5181a User manual
Agilent Technologies
Agilent Technologies 8360B User manual
Agilent Technologies
Agilent Technologies ESG-D Series Configuration guide
Agilent Technologies
Agilent Technologies N5161A User manual
Agilent Technologies
Agilent Technologies E4438C Operating instructions
Agilent Technologies
Agilent Technologies N4971A User manual
Agilent Technologies
Agilent Technologies E4423B Quick start guide
Agilent Technologies
Agilent Technologies 85901A Operation manual
Agilent Technologies
Agilent Technologies 75000 Series C User manual
