ADTRAN TRACER 4205 User manual

Converting the Frequency Plan of a TRACER 4205 System

Introduction

TRACER 4205 systems are shipped from the factory with the frequency plan programmed as Plan A or Plan B.

Each wireless link must contain a Plan A radio on one end and a Plan B on the other. A frequency plan

conversion may be performed in the field, but should only be attempted if absolutely necessary and must

always be performed by qualified personnel. This document outlines the procedure for changing the frequency

plan of a TRACER 4205 system.

Prerequisite Procedures

The current frequency plan configuration is listed on a label located on the rear panel of the unit (near the

Antenna connector). Record the current configuration before beginning this procedure.

Tools and Materials Required

• 5/16” Torque wrench (8 in-lbs)

• 3/16” nut driver

• Phillips-head screw driver

Disconnect all cables attached to the TRACER 4205 system (including power, data,

terminal RS-232, etc.) before performing this procedure.

Do not attempt to perform the conversion without the proper tools (see list below). Using

improper tools will damage the unit.

Electronic equipment can be damaged by static electrical discharge. Before handling

equipment, put on an antistatic discharge wrist strap to prevent damage to components.

Place equipment in antistatic packing material when transporting or storing. When

working on equipment, always place it on an approved antistatic mat that is electrically

grounded.

TRACER 4205 Frequency Conversion Document

1. Remove the screws from the chassis cover using a Phillips-head screwdriver (see Figure 1).

Figure 1. Removing the Cover Screws (TRACER 4205)

2. Remove the nuts on either side of the RS-232 connector (on the rear panel of the unit) using the 3/16”

nut driver (see Figure 2).

Figure 2. Removing the RS-232 Nuts

3. Carefully slide the cover toward the back of the unit until the front edge of the cover is disconnected

from the front of the unit. Lift the cover off and set aside.

Perform the steps below in the order listed.

Remove all connected mounting brackets before attempting to remove the unit cover.

TRACER 4205 Frequency Conversion Document

4. Verify the current frequency plan configuration. To verify the plan, check the connections between the

J connectors (located on the board and labeled J1 and J2) and the Chan connectors (located on the

diplexer). The Chan connectors are labeled CH1 and CH2 for most TRACER 4205 systems. The

following table outlines the connections for Plan A and B.

Click to see a digital image of the J connectors or the Chan connectors.

5. Using the torque wrench, disconnect both cables from the Chan connectors on the diplexer. Do not

attempt to disconnect the J connectors (located on the board) as this will cause damage. Click here for

a digital picture of this step.

6. Carefully flex the cables to swap the connections. Be careful with the RF cables, making sure that the

minimum bend radius of the cable is greater than 0.75"; bends and loops smaller than a quarter will

cause the RF cable to break. Use the wiring guidelines in Figure 3 for help with wire placement. Click

here for a digital picture of this step.

Figure 3. TRACER 4205 Cable Routing Diagrams

TRACER 4205

PLAN CHAN 1 CHAN 2

AJ2 J1

BJ1 J2

Allowing the RF cables to sit on the processor and radio boards (green) could cause

damage to the boards; keep the RF cables off the boards while re-routing them. Click here

for a digital picture of this mistake.

CH2 CH1

J1 J2

CH2 CH1

J1 J2

TRACER 4205 Frequency Conversion Document

7. Use the torque wrench to reconnect the RF cables to the Chan connectors. Tighten the cables by

turning clockwise until you hear a click from the wrench. DO NOT overtighten connectors as this will

cause the RF cable to break. The TRACER 4205 system will not operate properly with broken RF

cables.

8. Reinstall the cover and carefully tighten all screws.

9. Change label on back of the unit to reflect the Plan change.

>> BACK

Other ADTRAN Network Hardware manuals

ADTRAN

ADTRAN NetVanta 834 Owner's manual

ADTRAN

ADTRAN Total Access 372E User manual

ADTRAN

ADTRAN T200 H4R User manual

ADTRAN

ADTRAN Total Access 832 User manual

ADTRAN

ADTRAN NetVanta Series User manual

ADTRAN

ADTRAN jobAid NETVANTA User manual

ADTRAN

ADTRAN NetVanta 2000 Series User manual

ADTRAN

ADTRAN 4200990G1 Manual

ADTRAN

ADTRAN T200 HTU-R User manual

ADTRAN

ADTRAN Total Access 372 Product manual

ADTRAN

ADTRAN NIU3 Instruction Manual

ADTRAN

ADTRAN SLC-5 U-BR1TE III Instruction Manual

ADTRAN

ADTRAN TOTAL ACCESS 600R User manual

ADTRAN

ADTRAN Total Access 362R Product manual

ADTRAN

ADTRAN NetVanta 6360 User manual

ADTRAN

ADTRAN Total Access 300 Series Product manual

ADTRAN

ADTRAN TSU 120 User manual

ADTRAN

ADTRAN TOTAL ACCESS 1200 User manual

ADTRAN

ADTRAN Total Access DSLAM 16-Port ADSL2+ Access Module... User manual

ADTRAN

ADTRAN ISU 512E User manual

ADTRAN

ADTRAN CenturyLink C424G User manual

ADTRAN

ADTRAN 834-5 User manual

ADTRAN

ADTRAN Total Reach DDS-R Instruction Manual

ADTRAN

ADTRAN 1442300G1 User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide