ADTRAN DSU IV ESP User manual

DSU IV ESP

Data Service Unit with Embedded SNMP

User Manual

61204011L1-1B

May 2001

Part Number

1204011L1

1204001L1

1204002L2

1204004L1

1204005L1

Version

DSU IV ESP

ESP 4-wire Switched 56 DBU Card

ESP V.34 DBU Card

ESP ISDN DBU Card

ESP Ethernet Card

Trademark Information:

Hayes is a registered trademark of Hayes Microcomputer Products, Inc.

Openview is a registered trademark of Hewlett-Packard Company.

SunNet Manager is a registered trademark of Sun Microsystems, Inc.

Netview is a registered trademark of IBM

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

iii

The following conventions are used in this manual.

Important Safety Instructions

When using your telephone equipment, please follow these basic safety precautions

to reduce the risk of fire, electrical shock, or personal injury:

1. Do not use this product near water, such as near a bathtub, wash bowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming pool.

2. Avoid using a telephone (other than a cordless-type) during an electrical storm.

There is a remote risk of shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord, power supply, and/or batteries indicated in the manual.

Do not dispose of batteries in a fire. They may explode. Check with local codes for

special disposal instructions.

Save These Important Safety Instructions

Notes provide additional useful information.

Cautions signify information that could prevent service interruption.

Warnings provide information that could prevent damage to the

equipment or endangerment to human life.

Affidavit Requirements for Connection to Digital Services

• An affidavit is required to be given to the telephone company whenever digital

terminal equipment without encoded analog content and billing protection is

used to transmit digital signals containing encoded analog content which are

intended for eventual conversion into voice band analog signal and transmitted

on the network.

• The affidavit shall affirm that either no encoded analog content or billing informa-

tion is being transmitted or that the output of the device meets Part 68 encoded

analog content or billing protection specification.

• End use/customer will be responsible to file an affidavit with the local exchange

carrier when connecting unprotected CPE to a 1.544 Mbps or subrate digital ser-

vice.

• Until such time as subrate digital terminal equipment is registered for voice appli-

cations, the affidavit requirements for subrate services are waived.

Affidavit for Connection of Customer Premises Equipment to 1.544 MBPS and/

or Subrate Digital Services

For the work to be performed in the certified territory of ______________ (telco name)

State of ________________________________

County of ______________________________

I, _______________________ (name), ____________________ (business address),

_____________________ (telephone number) being duly sworn, state:

I have the responsibility for the operation and maintenance of the terminal equipment

to be connected to 1.544 Mbps and/or __________________ subrate digital services.

The terminal equipment to be connected complies with Part 68 of the FCC rules

except for the encoded analog content and billing protection specification.With

respect to encoded analog content and billing protection:

( ) I attest that all operations associated with the establishment, maintenance and adjust-

ment of the digital CPE with respect to encoded analog content and billing protection

information continuously complies with Part 68 of the FCC rules and Regulations.

( ) The digital CPE does not transmit digital signals containing encoded analog con-

tent or billing information which is intended to be decoded within the telecommuni-

cations network.

( ) The encoded analog content and billing protection is factory set and is not under

the control of the customer.

I attest that the operator(s) maintainer(s) of the digital CPE responsible for the estab-

lishment, maintenance and adjustment of the encoded analog content and billing

information has (have) been trained to perform these functions by successfully having

completed one of the following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/grantee of the equipment used

to encode analog signals; or

( ) B. A training course provided by the customer or authorized representative, using

training materials and instructions provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school or technical institution) rec-

ognized by the manufacturer/grantee of the equipment used to encode analog sig-

nals; or

( ) D. In lieu of the proceeding training requirements, the operator(s)/maintainer(S) is

(are) under the control of a supervisor trained in accordance with _______________

(circle one) above.

I agree to provide ____________________ (telco’s name) with proper documentation

to demonstrate compliance with the information in the preceding paragraph, if so

requested.

_____________________ Signature

_____________________ Title

_____________________ Date

Subscribed and sworn to before me

This _________ day of ___________________, 20__

_______________________________________

Notary Public

My commission expires: _________________________

vii

FCC regulations require that the following information be provided in this man-

ual:

1. This equipment complies with Part 68 of the FCC rules. On the bottom of the

equipment housing is a label that shows the FCC registration number and Ringer

Equivalence Number (REN) for this equipment, if applicable. If required, this

information must be given to the telephone company.

2. The following information may be required when applying to the local telephone

company for leased line facilities.

3. An FCC compliant telephone cord with a modular plug may be provided with

this equipment. This equipment is designed to be connected to the telephone net-

work or premises wiring using a compatible modular jack, which is FCC Part 68

compliant. See installation instructions for details.

4. If this equipment causes harm to the telephone network, the telephone company

may temporarily discontinue service. If possible, advance notification is given;

otherwise, notification is given as soon as possible. The telephone company will

advise the customer of the right to file a complaint with the FCC.

5. The telephone company may make changes in its facilities, equipment, operations,

or procedures that could affect the proper operation of this equipment. If this hap-

pens, the telephone company will provide advance notification and the opportunity

to make the necessary modifications to maintain uninterrupted service.

6. If experiencing difficulty with this equipment, please contact ADTRAN for repair and

warranty information. If the equipment is causing harm to the network, the telephone

company may request this equipment to be disconnected from the network until the

problem is resolved or it is certain that the equipment is not malfunctioning.

7. This unit contains no user serviceable parts.

8. The FCC recommends that the AC outlet to which equipment requiring AC

power is to be installed is provided with an AC surge arrester.

Service

Type Digital Facility

Interface Code Service Order

Code Network

Jacks

2.4 kbps Digital Interface

4.8 kbps Digital Interface

9.6 kbps Digital Interface

19.2 kbps Digital Interface

38.4 kbps Digital Interface

56 kbps Digital Interface

64 kbps Digital Interface

04DU5-24

04DU5-48

04DU5-96

04DU5-19

04DU5-38

04DU5-56

04DU5-64

6.0F

RJ-48S

viii

Federal Communications Commission Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction man-

ual, may cause harmful interference to radio frequencies. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

Shielded cables must be used with this unit to ensure compliance with Class A FCC

limits.

Canadian Emissions Requirements

This digital apparatus does not exceed the Class A limits for radio noise emissions

from digital apparatus as set out in the interference-causing equipment standard enti-

tled “Digital Apparatus," ICES-003 of the Department of Communications.

Cet appareil nuerique respecte les limites de bruits radioelectriques applicables aux

appareils numeriques de Class A prescrites dans la norme sur le materiel brouilleur:

"Appareils Numeriques," NMB-003 edictee par le ministre des Communications.

Change or modifications to this unit not expressly approved by the party re-

sponsible for compliance could void the user’s authority to operate the equip-

ment.

Canadian Equipment Limitations

Notice: The Canadian Industry and Science Canada label identifies certified equip-

ment. This certification means that the equipment meets certain telecommunications

network protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be con-

nected to the facilities of the local telecommunications company. The equipment must

also be installed using an acceptable methods of connection. In some cases, the com-

pany’s inside wiring associated with a single line individual service may be extended

by means of a certified connector assembly (telephone extension cord). The customer

should be aware that compliance with the above limitations may not prevent degra-

dation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian mainte-

nance facility designated by the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of

the power utility, telephone lines and internal metallic water pipe system, if present,

are connected together. This precaution may be particularly important in rural areas.

The Load Number (LN) assigned to each terminal device denotes the percentage of

the total load to be connected to a telephone loop which is used by the device, to pre-

vent overloading. The termination on a loop may consist of any combination of

devices subject only to the requirement that the total of the Load Numbers of all

devices does not exceed 100.

Users should not attempt to make such connections themselves,

but should contract the appropriate electric inspection authority,

or an electrician, as appropriate.

ISDN Service Ordering Information for the ADTRAN DSU IV ESP with ISDN Dial

Backup

For ADTRAN DSU IV ESP ISDN applications, the following guide can be used as an

aid in ordering basic ISDN service from your local telephone company. The ADTRAN

DSU IV ESP ISDN includes NT1 and Terminal adapter functionality and supports

data rates up to 64 kbps.

Request an ISDN Basic Rate Interface (BRI) line with the following features:

• U-interface reference point

• 2BIQ line coding

• 1 B+D Service (supports up to 64 kbps)

The DSU IV ESP ISDN supports the following switch types and software proto-

cols:

• AT&T 5ESS - Custom, 5E6 and later software, National ISDN-1

• NT DMS-100 BCS-32 and later software (Pvc1), National ISDN-1 (Pvc2)

• Siemens EQSD National ISDN-1

Request that the ISDN line allocate one DYNAMIC Terminal Endpoint Identifier (TEI)

for the number

For service offered from an AT&T 5ESS, request a point-to-point line with the fol-

lowing features:

•Feature:Value

•B1Service:On Demand (DMD)

• Data Line Class: Point-to-Point

• Maximum B Channels: 1 (1B+D)

• Circuit Switched Data (CSD) Bearer Channels: Any

•NumberofCSDCalls:1 (1B+D)

•TerminalType:Type A

Other manuals for DSU IV ESP

This manual suits for next models

Table of contents

Other ADTRAN Network Hardware manuals

ADTRAN

ADTRAN NetVanta 838 Operation manual

ADTRAN

ADTRAN Fractional T1 Tandem Channel Unit FT1-TDM User manual

ADTRAN

ADTRAN 12804108L1A User guide

ADTRAN

ADTRAN Ethernet Over Bonded Copper MX3112 User manual

ADTRAN

ADTRAN TRACER 5045 User manual

ADTRAN

ADTRAN 6540 Product manual

ADTRAN

ADTRAN 1202295L1 User manual

ADTRAN

ADTRAN 1200 Series User manual

ADTRAN

ADTRAN T200 HTU-R User manual

ADTRAN

ADTRAN HDSL 3192 HTU-C Instruction Manual

ADTRAN

ADTRAN 401 1 GE Micro ONT User manual

ADTRAN

ADTRAN 1200864L1 User manual

ADTRAN

ADTRAN SFP+ User manual

ADTRAN

ADTRAN Total Access 300 Instruction Manual

ADTRAN

ADTRAN NetVanta 1000 Series Manual

ADTRAN

ADTRAN IQ Probe 1200214L1 User manual

ADTRAN

ADTRAN DS3 NIU3 User manual

ADTRAN

ADTRAN DDM+ HTU-C M User manual

ADTRAN

ADTRAN Total Access 1248 User manual

ADTRAN

ADTRAN JOBAID T200 IDSL User manual

ADTRAN

ADTRAN TSU ESP User manual

ADTRAN

ADTRAN Total Access 300 Series User manual

ADTRAN

ADTRAN 1442880G1 User manual

ADTRAN

ADTRAN TSU ACE User manual

Popular Network Hardware manuals by other brands

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL product manual

B&B Electronics

B&B Electronics ZXT9-IO-222R2 product manual

Yudor

Yudor YDS-16 user manual

D-Link

D-Link ShareCenter DNS-320L datasheet

Samsung

Samsung ES1642dc Hardware user manual

Honeywell Home

Honeywell Home LTEM-PV Installation and setup guide

evertz

evertz 7700 Series manual

D-Link

D-Link ShareCenter DNS-343 Quick installation guide

Asante

Asante AsanteBridge 1012 user guide

FireBrick

FireBrick FB2700 user manual

Audiovox Electronics

Audiovox Electronics ARWH2T user manual

ADC

ADC DSX-1 Operational Procedures Guide

NetComm

NetComm NF2 user guide

Alcatel-Lucent

Alcatel-Lucent 5620 user guide

Dell EMC

Dell EMC XC6420 Series Solution guide

Lanner

Lanner NCA-1020A user manual

Allied Telesis

Allied Telesis AT-TN121-A Specifications

Arista

Arista CCA-ETM-Q12 quick start guide