Adherium Smartinhaler User manual
PRODUCT MANUAL
Preparation for First Use
Warnings, Cautions, and Notes
Smartinhaler™Sensor Components
Terms and Abbreviations
Compatible MDI Devices
Installing or Removing an MDI
Setting up Bluetooth®Communications
Delivering a Dose of Medication
Reminders
Reviewing Smartinhaler™Sensor Usage Data
Manually Uploading Stored Information
Reviewing Battery Level
Recharging the Smartinhaler™Sensor -
Rechargeable Sensor Only
Cleaning the Smartinhaler™Sensor and MDI
4
5
5
6
6
6
10
10
12
12
12
13
14
14
Table of Contents
Preparation for First Use
Warnings, Cautions, and Notes
Smartinhaler™Sensor Components
Terms and Abbreviations
Compatible MDI Devices
Installing or Removing an MDI
Setting up Bluetooth®Communications
Delivering a Dose of Medication
Reminders
Reviewing Smartinhaler™Sensor Usage Data
Manually Uploading Stored Information
Reviewing Battery Level
Recharging the Smartinhaler™Sensor -
Rechargeable Sensor Only
Cleaning the Smartinhaler™Sensor and MDI
4
5
5
6
6
6
10
10
12
12
12
13
14
14
Storage
Troubleshooting
Servicing
Disposal
Smartinhaler™Sensor Intended Use
How the Smartinhaler™Sensor Works
Safety and Usage Information
Symbols
Warranty
Specications
Smartinhaler™Sensor Specications
FCC Statement
IC Statement
RF Exposure Statement
Declaration of Conformity
15
15
16
16
16
17
17
18
19
19
20
20
21
22
22
4
Preparation for First Use
Rechargeable Sensor - NF0090
Following manufacture the Smartinhaler™sensor is
placed in Deep-Sleep mode to conserve battery life.
Before rst use, place the Smartinhaler™sensor on charge
for a minimum of 3 hours or until the LED stops ashing
green. This will wake the Smartinhaler™sensor from Deep-
Sleep mode and the Smartinhaler™sensor is ready to use.
Non-Rechargeable Sensor - NF0091
Following manufacture, the Smartinhaler™sensor is
placed in Deep-Sleep mode to conserve battery life.
To wake up the Smartinhaler™sensor, hold down the
Status Button for 3 seconds and then release. Press
the Status Button once more to check the battery level.
The Smartinhaler™sensor LED should ash green prior
to rst use.
Warnings, Cautions, and Notes
Warnings identify actions or situations that could
lead to personal injury. Take note of all warnings
before using the Smartinhaler™sensor.
Cautions identify actions or situations that
could damage the Smartinhaler™sensor or other
equipment, or affect the accuracy or availability of
recorded actuation data.
Notes contain advisory information about some
aspect of the Smartinhaler™sensor or its use.
5
Smartinhaler™Sensor Components
Key:
1. Use only with this medication
2. Light Emitting Diode (LED)
3. Battery type – see Symbols section for more information
4. Status Button (reminder button/battery check button)
5. USB port (only used for NF0090 to recharge battery)
Terms and Abbreviations
MDI Metered Dose Inhaler.
Compatible MDI Devices
The Smartinhaler™sensor is designed to work
only with the MDI and medication indicated on the
Smartinhaler™sensor label.
6
Installing or Removing an MDI
Installation (for non-tethered MDI)
To install the Smartinhaler™sensor, align the MDI with
the back of the Smartinhaler™sensor. Push the MDI
rmly into the Smartinhaler™sensor, ensuring the
mouth piece of the MDI goes through the front window
on the Smartinhaler™sensor.
7
Removal (for non-tethered MDI)
While holding each side of the Smartinhaler™sensor,
gently push the mouthpiece of the MDI to remove the
MDI from the Smartinhaler™sensor.
8
Installation (for tethered MDI)
To install the Smartinhaler™sensor, open the MDI cap,
and align the MDI with the back of the Smartinhaler™
sensor. Push the MDI rmly into the Smartinhaler™
sensor, ensuring the mouth piece of the MDI goes
through the front window on the Smartinhaler™sensor.
Close the MDI cap.
9
Removal (for tethered MDI)
Open the MDI cap. While holding each side of the
Smartinhaler™sensor, gently push the mouthpiece of
the MDI to remove the MDI from the Smartinhaler™
sensor. Close the MDI cap.
10
Setting Up Bluetooth®Communications
The Smartinhaler™sensor must be paired with a
compatible Bluetooth®smartphone or tablet computer
in order to upload stored usage data. Refer to
Smartinhaler™App on App store or on Google Play
for more information. To pair the Smartinhaler™sensor
with a smartphone or tablet computer:
1. Follow the instructions on your smartphone or tablet
computer to put it in pairing mode.
2. On the Smartinhaler™sensor press the Status
Button 3 times quickly to enter pairing mode. The
LED will ash blue when the Smartinhaler™sensor is
in pairing mode.
3. Follow any prompts on your smartphone or tablet
computer to select and accept pairing with the
Smartinhaler™sensor. The LED will ash green to
indicate pairing is successful.
If pairing is not successful within 60 seconds the
LED will ash red. The pairing process can be
repeated if necessary.
The Smartinhaler™ sensor can only be paired with
a single smartphone or tablet computer at a time.
Starting the pairing process removes the current
paired Smartinhaler™ sensor.
Delivering a Dose of Medication
Refer to the labelling provided with the inhaler for
instructions on use. Carry out all steps required to use
your inhaler according to the instructions.
The Smartinhaler™sensor LED ashes after detecting a
medication dose has been actuated.
This manual suits for next models
3
Table of contents
Other Adherium Accessories manuals
