Addonics Technologies ZESSIU3CS User manual

Addonics

TECHNOLOGIES

Z USB3.0 / eSATA Combo Drive Enclosure

for SATA or IDE Hard drive or Optical drive

Model: ZESSIU3CS

User’s Guide

FCC Warning Statement

This equipment has been tested and found to comply with the limits for a cl ass B digital

device pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy. If not installed and

used in accordance with the instructions, it may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If the equipment does cause harmful interf erence to radio or

television reception, which can be determined by turning the equipment on and off, the user

is encouraged to try and correct the interference by one or more of the following

suggestions.

Reorient or relocate the receiving antenna

Increase the distance between the equipment and the receiver

Connect the equipment to a different power outlet other than the one where receiver is

connected

Consult a certified television or radio technician

TECHNICAL SUPPORT

Phone: 408-453-6212

Hours: 8:30 am - 6:00 pm PST

Email: http://www.addonics.com/support/query/

Enclosure Overview

Removing the front panel

You can remove the front panel of the enclosure to

access the drive drawer of the optical drive.

Step 1

Loosen the two screws from the rear panel. Pull out the interior tray from the

enclosure.

Step 2

A. Installing a 3.5” SATA hard drive

Slide in the 3.5”

SATA hard drive

and secure on the

tray using screws.

Screw 1 Screw 2

Power

Connector

Switch

Fan eSATA Port

SATA hard

drive

B. Installing a 3.5” IDE hard drive

The Z USB3.0 / eSATA combo drive enclosure comes with an IDE to

SATA converter.

Note: It is required to set up the IDE hard drive you are connecting to

the converter as a MASTER device.

1. Locate the 40-pin IDE connector of your IDE drive.

2. Connect the converter board to the IDE connector of the hard drive.

3. Using the provided Y-power cable, connect the 4-pin Molex

connector to the power connector on the hard drive. This will

provide power to the hard drive.

4. At the other end of the Y-power cable is the 4-pin floppy power connector

which you connect to the converter. Now connect the SATA cable to the

SATA port on the converter.

5. Disconnect the SATA board from the drive enclosure. Then connect the

SATA cable to the SATA port on the IDE to SATA converter

Step 3

Use the enclosed screws to secure the hard drive to the tray.

Screw holes

ADSAIDE

IDE to

SATA converter

SATA Port

4-Pin Floppy

Power

40-pin IDE Connector

4-pin Molex

Power Connector

Master or Slave

Jumper Settings

SATA board

40-pin IDE Connector

Other Addonics Technologies Enclosure manuals

Addonics Technologies

Addonics Technologies ZSAUSCSF User manual

Addonics Technologies

Addonics Technologies Z4RCS25PM User manual

Addonics Technologies

Addonics Technologies CPR5SA User manual

Addonics Technologies

Addonics Technologies Console Drive USIB35 User manual

Addonics Technologies

Addonics Technologies MST5HMXA User manual

Addonics Technologies

Addonics Technologies AE5IDECSU2 User manual

Addonics Technologies

Addonics Technologies NAS25HDU2 User manual

Addonics Technologies

Addonics Technologies ZSNESA User manual

Addonics Technologies

Addonics Technologies SU3CS User manual

Addonics Technologies

Addonics Technologies External USB2.0 User manual

Addonics Technologies

Addonics Technologies AE25RDESU User manual

Addonics Technologies

Addonics Technologies MSUDDSA User manual

Addonics Technologies

Addonics Technologies AD5HPMRXA-E User manual

Addonics Technologies

Addonics Technologies ZESU2CS User manual

Addonics Technologies

Addonics Technologies ZSNESU3 User manual

Addonics Technologies

Addonics Technologies ZESU3CS User manual

Addonics Technologies

Addonics Technologies AE5RCS35NSA User manual

Addonics Technologies

Addonics Technologies AE5IDECSUF User manual

Addonics Technologies

Addonics Technologies ZESAES256 User manual

Addonics Technologies

Addonics Technologies RT3DA5HP User manual

Addonics Technologies

Addonics Technologies DIEDES User manual

Addonics Technologies

Addonics Technologies RR2035ASDML User manual

Addonics Technologies

Addonics Technologies DCED256ES User manual

Addonics Technologies

Addonics Technologies SESCS User manual

Popular Enclosure manuals by other brands

SilentiumPC

SilentiumPC Armis AR5 Hardware installation

Pulsar

Pulsar 17/TRP80/DSPR Assembly instructions

Thermaltake

Thermaltake V150 TG user manual

MSI

MSI MPG SEKIRA 500X quick start guide

Antec

Antec Dark fleet DF-10 user manual

Nexans

Nexans WTC05 installation manual

Peavey

Peavey DS 1502 Specifications

D-Link

D-Link ShareCenter Pro DNS-1550-04 user manual

Rosewill

Rosewill RX82-U(JBOD) user manual

QNAP

QNAP SAS JBOD CLI 1.0 user guide

GAMDIAS

GAMDIAS Talos P1 Quick installation guide

Auvs

Auvs KR615 user manual

Digitus

Digitus DA-71114 manual

CommScope

CommScope FDH 3000 user manual

FS FHD-FWME4 quick start guide

JBL

JBL CS1215T owner's manual

Pulsar

Pulsar ARAD-S4 manual

Pulsar

Pulsar AWO454 Assembly instruction