Adaptive Technologies Group MultiMount MM-023 User manual

Installation Guide

MultiMount™

Thank you for selecting the MultiMount™ MM-023 speaker Mounting kit is

designed for speaker with 100x100mm and 90x90mm hole pattern. This

mounting kit contains one speaker mount that positions speakers weighing up to

60 lb/27 kg. from most wall and ceiling structures. The MultiMount-023 simplifies

and speeds up wall and ceiling speaker installations while achieving a very

versatile range of speaker positioning.

MM-023

Note to installers:

Due to the wide variety of wall structures, materials and mounting

methods, these instructions assume that the installing contractor will

exercise proper judgment in selecting the mounting area and hardware.

As a guide, the installation, when complete should be capable of supporting

5 to 10 times the actual applied load. Always use a back-up safety system

such as a safety cable.

To assure a trouble free installation, read through and follow these

instructions carefully before beginning. If you have doubts about the integrity

of the structure you are mounting to or you are not sure about the proper

hardware to use, consult a structural and/or hardware specialist.

Be sure that all of the following items are included in this kit before

proceeding:

1 pc Mounting plate 1 pc Speaker adapter plate

1 pc Support Arm Assy. 1 pc Instruction sheet

1 pc stop pin

Note: Screws and washers to attach speaker to adapter plate are not

included.

Step 1:

Disassemble the wall mount plate from the support arm by removing the 5/16”

hex bolt and pan locking washer (Figure 1).

Step 2: Mounting to a Wall:

Attach the mounting plate to the wall with the open center slot towards the

ceiling using the appropriate hardware for the application (Figure 1). If in

doubt, consult a local hardware specialist. Make sure the stop pin is placed into

the lower center hole of the wall plate (Figure 2).

Mounting to a ceiling predetermine the desired direction of the speaker. Attach

the mounting plate to the ceiling structure with the open center slot towards the

speaker using the appropriate hardware for the application.

Figure 1

Step 3:

Lightly loosen the ¾” bolts securing the speaker adapter plate to the support

arm’s pivot rod. The support arm should be able to rotate easily without

binding. Attach the speaker adapter plate and support arm assembly to the

appropriate mounting holes of the speaker using the manufacturer’s

suggested screws and washers. The support arm should face the lower end

of the speaker. Tighten these fasteners permanently. If threaded inserts are

not included on the speaker, consult the speaker manufacturer for proper

mounting procedures. (Figure 3).

Step 4:

Lift the speaker and support arm up to the mounting plate and insert

the arm through the end of the mounting plate with the cross slot

(Figure 4). Line up the support arm’s threaded hole with the cross-slot.

Insert the 5/16” hex bolt with the pan locking washer through the

mounting plate’s slot and into the threaded hole of the support arm

(Figure 4). Be sure the pan locking washer is seated vertically outside

the slot.

Figure 2

Figure 3

Figure 4

Step 5: Setting the pan angle:

Rotate the speaker horizontally right or left until the speaker

is aimed in the desired direction. Permanently tighten the

hex bolt at the mounting plate (Figure 5).

Step 6: Setting the tilt angle

While supporting the speaker’s weight, lift the speaker up to

the desired tilt angle and hold it in position. Tighten the 3/4”

hex bolts at the sides of the speaker adapter plate, one is a

right hand thread and one is a left hand thread. Rotate the

left hand thread bolt on the grooved side of the pivot rod

counterclockwise to tighten. Rotate the other opposite bolt

clockwise to tighten. Be sure that the bolts have been

tightened permanently before releasing the weight of the

speaker (Figure 6).

If the tilt angle needs to be adjusted, DO

NOT PULL ON SPEAKER, rather loosen

the bolts then repeat step 6.

Step 7: Recommendation: Install Safety Cable

Attach a safety cable (sold separately) to the mounting

surface (Must be able to support at least five times the

weight of the speaker), then attach the other end of the

safety cable to the speaker. If no attachment is provided on

speaker, consult speaker manufacturer for advice on best

attachment point and method

Figure 5

Figure 6

This manual suits for next models

Table of contents

Other Adaptive Technologies Group Rack & Stand manuals

Adaptive Technologies Group

Adaptive Technologies Group WM-0-15-60 User manual

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-18 User manual

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-120 User manual

Adaptive Technologies Group

Adaptive Technologies Group SAS-100-CA User manual

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-120 User manual

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-024 User manual

Adaptive Technologies Group

Adaptive Technologies Group SAS-2WA-Series User manual

Adaptive Technologies Group

Adaptive Technologies Group MM-016-BT User manual

Adaptive Technologies Group

Adaptive Technologies Group UB-QX500 Operating and maintenance instructions

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 