Actidata ActiLib Autoloader 1U Operating and maintenance instructions

actiLib Autoloader 1U –Quick Start Guide

Page 1of 17

actiLib Autoloader 1U

Quick Start Guide

September, 2009

actiLib Autoloader 1U –Quick Start Guide

Page 2of 17

1 Contents

1Contents ...................................................................................................................................... 2

2General Warnings ....................................................................................................................... 3

3Unpacking the tape loader ......................................................................................................... 5

3.1 Identifying product components.......................................................................................... 6

3.2 Remove the shipping lock................................................................................................... 6

3.3 Rack mounting the tape loader........................................................................................... 7

4Front panel ................................................................................................................................ 10

4.1 Rear panel ........................................................................................................................ 11

5Labeling tape cartridges .......................................................................................................... 13

6Magazines.................................................................................................................................. 14

6.1 Inserting tape cartridges into a magazine ......................................................................... 14

6.2 Removing and replacing a magazine using the OCP ....................................................... 14

6.3 Slot numbering.................................................................................................................. 15

6.4 Mailslot.............................................................................................................................. 15

7Connecting the Library............................................................................................................. 16

7.1 SCSI installation:.............................................................................................................. 16

7.2 SAS installation:................................................................................................................ 16

7.3 Fibre-channel installation:.................................................................................................16

7.4 Configuring the library:...................................................................................................... 16

8Power ON/OFF the library ........................................................................................................ 17

actiLib Autoloader 1U –Quick Start Guide

Page 3of 17

2 General Warnings

DANGER

High voltage!

Risk of electric shock.

Do not remove cover (or back). No user-

serviceable parts inside.

Refer servicing to qualified service personnel.

CAUTION

Static sensitive!

A discharge of static electricity can damage static-

sensitive devices or micro circuitry. Proper packaging

and grounding techniques are necessary precautions to

prevent damage.

Read this manual

Do not open Top Cover

No servicing except that which is described in this manual

Ensure proper ventilation

Keep away from heat sources

Use proper power sources

Properly routed power cable

Precautions

Do not expose the unit to moisture. The operating temperature for this unit is between 10°C

(50°F) and 35°C (95°F).

Use the unit on a firm level surface free from vibration

Do not place anything on top of the unit that weighs more than 15 kg.

Product warranty Caution

The warranty for the tape loader shall not apply to failures of any unit when:

The tape loader is repaired or modified by anyone other than the manufactures personnel or

approved agent.

The tape loader is physically abused or used in a manner that is inconsistent with the

operating instructions or product specification defined by the manufacturer.

The tape loader fails because of accident, misuse, abuse, neglect, mishandling,

misapplication, alteration, faulty installation, modification, or service by anyone other than the

factory service center or its approved agent.

The tape loader is repaired by anyone, including an approved agent, in a manner that is

contrary to the maintenance or installation instructions supplied by the manufacturer.

The manufacturer's serial number tag is removed.

The tape loader is damaged because of improper packaging on return.

actiLib Autoloader 1U –Quick Start Guide

Page 4of 17

Unauthorized modifications to the unit configuration by the customer may result in loss of

guarantee by the vendor.

Rack stability

WARNING

Weight!

To reduce the risk of personal injury or damage to

equipment

Extend leveling feet to the floor.

Ensure that the full weight of the rack rests on

the leveling feet.

Install stabilizing feet on the rack.

In multiple-rack installations, secure racks

together.

Extend only one rack component at a time.

Racks may become unstable if more than one

component is extended

actiLib Autoloader 1U –Quick Start Guide

Page 5of 17

3 Unpacking the tape loader

Before you begin, clear a work surface to unpack the loader. Select an open 1U rack location allowing

easy access to the host server and an easily accessible power outlet.

IMPORTANT

If the temperature in the room where the loader will be

installed varies by 15º C (30º F) from the room where the

loader was stored, allow the loader to acclimate to the

surrounding environment for at least 12 hours before

unpacking it from the shipping container.!

Unpacking the loader:

1. Before opening and removing the loader from the box, inspect the container for shipping damage.

If you notice any damage, report it to the shipping company immediately.

2. Open the box.

3. Carefully remove the shipping materials from the top of the loader (see Figure ). Remove the

accessory package (if present) and set aside.

4. Remove the two rack rails (if included) and set aside.

Figure 1Unpacking the loader

actiLib Autoloader 1U –Quick Start Guide

Page 6of 17

Number

Description

Top shell

Rack mount Kit

Unit

Bottom shell

Box

Table 1Unpacking the loader

5. Lift the loader out of the carton and remove the bag from the loader. Save the packaging materials

for future use.

IMPORTANT

Do not place the loader on either end or sides as this

may damage the loader.!

3.1 Identifying-product-components-

Confirm that you have received the following:

Loader

Terminator (not in all configurations)

SCSI cable (not in all configurations)

Power cord (not in all configurations)

Rack mount kit

Quick Start Guide

3.2 Remove-the-shipping-lock-

IMPORTANT

The shipping lock, which prevents the robotic transport

mechanism from moving during shipment, must be

removed before the loader is powered on.

The shipping lock is held in place with a label and is located in the top center of the loader. After the

shipping lock is removed, it should be stored on the rear panel right side (next to power connector) of

the loader for future use.

To remove and store the shipping lock:

1. Remove the yellow label that is securing the lock to the top of the loader, and then remove the

lock (see Figure 2).

actiLib Autoloader 1U –Quick Start Guide

Page 7of 17

Figure 2Shipping lock and label

2. Store the shipping lock next to power supply (see Figure 3).

IMPORTANT

If you need to transport the loader, it is recommended

that the shipping lock and label is replaced on the top

cover

Figure 3Shipping lock next to power supply

3.3 Rack-mounting-the-tape-loader-

The loader easily installs into a standard 19” rack system taking up 1U of space.

The actiLib Autoloader 1U weighs 13.1 kg (29 lbs) with 8 cartridges

WARNING

Weight!

Risk of personal injury or damage to the loader.

always remove all tapes to reduce the overall

weight of the loader

observe local health and safety requirements

and guidelines for manual material handling

Required tools:

#3 Phillips screwdriver

T10 Torx screwdriver

There are two sets of eight M6 screws in the accessory package that came with your loader. The type

of rack that you have will determine the type of M6 screw that you will use.

To install the loader:

1. Determine the location in yourrack for your loader to be installed and, using a pencil, mark the

location on each vertical rail in yourrack.

2. Using the appropriate M6 screws for your rack type, and a #3 Phillips screwdriver, secure one rail

to each side of the rack in your chosen rack location. Secure both the front and back of each rail to

actiLib Autoloader 1U –Quick Start Guide

Page 8of 17

the rack. The rails extend to fit a variety of rack depths. The correct orientation of the left and right

rails is shown in Figure 4.

Figure 4Installing the rails into the rack

1. Using the Torx screwdriver, remove the screw on each side of your loader. Shown in 5step1.

Figure 5Installing the mounting brackets and guide pulleys

2. Install the loader guide pulleys on each side of the loader using the 2 Torx screws included in the

rack kit (see Figure 5 step 2).

Install the mounting brackets of the loader using the 4 Torxs screws included in the rack kit. Shown in

Figure 5(step 3).

3. With loader guide pulleys and mounting brackets installed, slide the loader onto the rails.

4. Secure the loader to the rack (see Figure 6) using a 3# Phillips screwdriver placed through the

small holes in the mounting bracket to tighten the M5 screw on each side of the loader.

actiLib Autoloader 1U –Quick Start Guide

Page 9of 17

Figure 6Securing the loader to the rack

actiLib Autoloader 1U –Quick Start Guide

Page 10 of 17

4 Front panel

The front of the actiLib Autoloader 1U is used to access the power button, operator control panel

(OCP), left and right magazines, LED’s, and the mail slot.

The Operator panel consists of an LCD display with a 2x16 character matrix, 4 push button switches

and a power on/off button. The circuitry to illuminate external LED’s has also been incorporated into

the current level of hardware

Figure 7Front panel

Number

Description

Left magazine with Mail slot

Power button.

Pressing the button will initiate a controlled Power Down of the unit (soft power

down

LED “READY” (Green).

Illuminated when power is on. Blinking when there is tape or loader robotics activity.

LED “CLEAN” (Amber).

Illuminated when the tape drive has determined that a cleaning cartridge should be

used. Cleaning is only necessary when the loader directs you to do so. Additional

cleaning is not necessary.

LED “ATTENTION” (Amber).

Illuminated if the loader has detected a condition that requires attention by the

operator.

LED “ERROR” (Amber).

Illuminated if an unrecoverable tape drive or loader error occurs. A corresponding

error message displays on the LCD screen (see for more information).

Control key “UP” button

The UP button is used to navigate through menu items.

Control key “CANCEL” button [X]

Other manuals for actiLib Autoloader 1U

Table of contents

Other Actidata Storage manuals

Actidata

Actidata actiLib Library 2U User manual

Actidata

Actidata actiNAS BB212-3 User manual

Actidata

Actidata actiLib Autoloader 4U User manual

Actidata

Actidata actiDisk RDX User manual

Actidata

Actidata actiNAS Cube SL User manual

Actidata

Actidata Ti-NAS QT-6 User manual

Actidata

Actidata actiTape LTO-3 User manual

Actidata

Actidata actiNAS SL 1U-4 User manual

Actidata

Actidata actiNAS XL 2U-12 User manual

Actidata

Actidata actiLib Autoloader 2U Troubleshooting guide

Popular Storage manuals by other brands

QNAP

QNAP TS 32PXU Series user guide

LaCie

LaCie RUGGED RAID user manual

Freecom

Freecom CLS DOCK Quick install guide

PNY

PNY Attache P-FD64MBATT3 install guide

HP StorageWorks MSL2024 Getting started

OLT

OLT 6x6 Maximizer Assembly manual

Transcend

Transcend JetFlash 160 Specifications

LaCie

LaCie RUGGED MINI user manual

Thunderbolt

Thunderbolt 600 user manual

Panasonic

Panasonic LB-DH8 series Operator's guide

Intel

Intel RAID High Availability user guide

LaCie

LaCie 12big Thunderbolt 3 Quick install guide

Spectra Logic

Spectra Logic T-Series Spectra T50e quick start guide

Panasonic

Panasonic LKM-F931-1 instruction manual

Tabernus

Tabernus Enterprise Erase E2400 user guide

Rocstor

Rocstor COMMANDER 3F series user manual

HP P9000 user guide

Western Digital

Western Digital Ultrastar Data60 installation guide

Actidata actiLib Autoloader 1U Operating and maintenance instructions

Popular Storage manuals by other brands