ACME TV LIGHT PANEL 2000 User manual

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3 Control Panel .................................................................................................. 5

4. The Plate for Barn Door Installation............................................................... 6

5. How To Set The Unit....................................................................................... 6

5.1 Main Function.......................................................................................... 6

6. Control By Universal DMX Controller ........................................................... 11

6.1 DMX512 Connection.............................................................................. 11

6.2 Address Setting ...................................................................................... 12

6.3 DMX512 Configuration........................................................................... 12

7. Troubleshooting........................................................................................... 14

8. Fixture Cleaning ........................................................................................... 14

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

210W

Light Source:

480pcs 0.5W CW LED (CW)

480pcs 0.5W WW LED (WW)

Color Temperature:

5600±250K (CW)

3200±150K (WW)

Beam Angle:

110°

Optical:

CRI: CW≥94, WW≥95

CQS: CW≥94, WW≥94

TLCI: CW≥95, WW≥95

Control:

DMX Channel: 1/2A/2B/3 Channels

Control Mode: DMX, Primary/Secondary, Art-Net

Firmware Upgrade: Update via DMX link

Construction:

Display: LCD display

Data In/Out: 5-pin XLR (3-pin XLR is optional)

Power In/Out: Power Connector in

Protection Rating: IP20

Features:

With outstanding floodlight and soft light, TV LIGHT PANEL 2000 are widely applied to photographic

studio, TV station, conference room, shopping mall; Access to buttery.

Dimension/Weight:

668x148x491mm, 13kgs

26.3"x5.8"x19.3"in, 28.7lbs

Photometrics Diagram:

3 Control Panel

1. Display: To show the various menus and the selected function

2. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To go forward to move down in the menu

ENTER

To perform the desired functions

3. DIMMER: Adjust the dimmer

4. FUSE(T 5A): Protects the unit from over-voltage or short circuit

5. MAINS IN: To connect to supply power

6. BATTERY (DC 48V): Connects to external battery

7. DMX OUT: Use 5-pin XLR cable to link the next units (3-pin XLR is optional)

8. DMX IN: Use 5-pin XLR cable to link the unit and DMX controller (3-pin XLR is optional)

9. ETHERNET: Transfers fixture’s information to a main controller

4. The Plate for Barn Door Installation

At first, please push the barn door by hand.

Screw

Secondly, please put the Barn Door into the unit, to fasten the screws of the slot, then finish the

barn door installation.

5. How To Set The Unit

5.1 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

DMX Setting

To select DMX Setting, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address, Art-Net Setup or Channel Mode.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the

address from 001 to 512, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Art-Net Setup

To select Art-Net Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or Art-Net Port Setup, press the ENTER button to store. Press the MENU button

back to the last menu or let the unit idle 30 seconds to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select 1

CH, 2A CH, 2B CH or 3 CH, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Dimmer Speed

To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select

Smooth or Fast, press the ENTER button to store. Press the MENU button back to the last menu or

let the unit idle 30 seconds to exit menu mode.

Dimmer Curve Setting

To select Dimmer Curve Setting, press the ENTER button to confirm. Use the UP/DOWN button to

select Linear Curve, Sq. Law Curve, Invert Sq. Law Curve or S Curve, press the ENTER button to

store. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu

mode.

Optically Linear: The increase in light intensity appears to be linear as DMX value is increased.

Square Law:Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.

Pri./Sec. Mode

To select Pri./Sec. Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

Primary or Secondary, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

DMX Last State

To select DMX Last State, press the ENTER button to confirm. Use the UP/DOWN button to select

Pri.Sec., Blackout or Hold, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Frequency

To select Frequency, press the ENTER button to confirm. Use the UP/DOWN button to select 900hz,

1000hz, 1100hz, 1200hz, 1300hz, 1400hz, 1500hz, 2500hz, 4000hz, 5000hz, 10000hz, 15000hz,

20000hz or 25000hz, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Display Setting

To select Display Setting, press the ENTER button to confirm, use the UP/DOWN button to select

Contrast Ratio, Backlight Auto Off, Invert Display or Language.

Contrast Ratio

Select Contrast Ratio, press the ENTER button to confirm, present mode will blink on the display,

use the UP/DOWN button to adjust the contrast ratio from 1to 30, press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Other manuals for TV LIGHT PANEL 2000

Table of contents

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions