9510-0847 Rev C
11-23-09
PSG Controls, Inc.
LIMITED WARRANTY POLICY
PSG Controls, Inc. (Hereinafter referred to as "PSG") warrants the following:
Only cataloged products sold to distributors are warranted to the original purchaser, to
conform with specifications furnished or approved by PSG, and to be free from defects in
material and workmanship, for a period of one (1) year from the date of purchase, unless
specified in writing for a different period.
Any PSG product that proves defective within the above described warranty period will
be repaired or replaced (at PSG's option) free of any charge if returned to the PSG
factory at 1225 Tunnel Road, Perkasie, PA. 18944 with transportation charges prepaid.
Prior to returning this product to PSG, the purchaser shall give PSG notice in writing
stating how this product fails to fulfill this warranty. No product shall be accepted for
repair or replacement without a required written notice and without prior written
authorization and shipping instructions having been received by the purchaser from
PSG. Only PSG's factory is authorized to perform services under this warranty.
This warranty does not extend to any product that has been subjected to misuse, abuse,
neglect, accidents, alterations, improper installation or use in violation of the printed
instructions furnished by PSG. This warranty neither applies to batteries nor
deterioration of, nor damage to the product caused by the use of faulty batteries. Final
determination as to whether any product is actually defective rests solely with PSG.
This warranty is expressly in lieu of all other agreements and warranties, expressed,
implied, or statutory and PSG has no other obligations or liabilities in connection with this
product. In no event shall PSG's obligation or liability hereunder exceed the purchase
price of this product. PSG SHALL NOT IN ANY EVENT BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal
rights, and you also have other rights which vary from state to state. Some states do not
allow the exclusion or limitation of incidental or consequential damages, or implied
warranties, so the above limitations or exclusion may not apply to you.
Toll free technical assistance is available
via our technical hotline: 1-800-523-2558
Mon-Fri, 8:00 A.M. to 4:30 P.M. Eastern Standard Time
1225 Tunnel Road - Perkasie, PA 18944 - 215-257-3621 - Fax 215-257-4288
RPSG Controls, Inc.
2
SW5 Settings:
1234
OFF ON
Position 1, Not used
Position 2, Not used
Position 3, Not used
Position 4, differential, OFF (0.5°), ON (1.0°)
SW5
Configuration
Switches
Wire
Terminal
Block
Energy
Harvesting
Switch
X
RH
W1
GENERAL INSTRUCTIONS:
This control should be installed and serviced by a qualified contractor.
1. Caution: Make sure that power to the control has been turned
off before doing any installing or service work. Class 2 transformers
can be damaged if a short circuit occurs when disconnecting wires
from the old thermostat.
2. All wiring must conform to local and state codes and ordinances.
3. A thorough check-out of the system must be made after the
control has been installed.
4. This thermostat was designed to operate as a energy harvesting
control. A common wire is optional. If the thermostat is connected
directly to a logic board at the equipment, in order for it to function,
it may be necessary to connect a common to the thermostat and
turn off the energy harvesting switch.
MOUNTING THE CONTROL:
1. Open case as shown.
2. Choose a location about 5 feet above the floor, in an area where
there is good air circulation. Such an area will provide an average
room temperature.
3. Do NOT mount thermostat where it may be affected by drafts, hot
or cold air from ducts or radiant heat from the sun or appliances.
4. Pull thermostat cable through hole in wall or outlet box.
5. Plug wall hole to prevent drafts which may affect thermostat.
6. Use the screws supplied to mount the case on the wall.
7. This control is not position sensitive. However, heat rises and
some heating does occur in the control. It is recommended that
the unit be mounted with the top up.
INSTALLING PLUG-IN SETPOINTS:
Installing the pre-set plug-in temperature setpoints is as easy as
installing a fuse. Direction does not matter. The large plated tabs
must be pointed toward the thermostat. Press the plug-in setpoint
firmly into position.
NOTE: The plug-in setpoints must be installed at all times.
Removal of the setpoints will disable the thermostat.
