ABSCO SHEDS CYCRK Installation guide
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 1
DOWNLOAD
OUR APP FOR
ASSEMBLY
VIDEOS
LEAVE A REVIEW
Tell us about your experience and
receive a $20 Coles Gift Card.
Visit www.abscosheds.com.au/review
AU: 1800 029 701
NZ: 0800 466 444
www.abscosheds.com.au
This kit is applicable to the following sheds:
The addition of this frame kit will increase the
wind rating of the specified sheds to
Wind rating: N3/C1 as per AS4055-2012.
Suitable for specific cyclonic regions
30372RK
30292RK
30222RK
30142RK
23221RK
23141RK
WARNING: This shed must be anchored to a
100mm thick concrete slab with the concrete
anchors supplied.
Failure to do so will result in the shed not
having the structural integrity required to
endure a severe storms or cyclonic event.
WARNING: Doors must remain closed with
all padbolts properly secured during severe
storms or cyclonic event.
Where information conflicts with the original
instruction manual, this document is to be
referenced.
View of frame kit applied to
30372RK
This instruction manual is to be used during
the initial construction of the structure.
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
• Local authority approval must be obtained prior to construction of the shed. Once you have
selected your site you will need to lodge a site plan to your local council.
• The bracing material supplied is 80 x 40 mm galvanised steel channel, similar to that used in steel
house framing. Some channels are required to be cut to specific lengths using a hacksaw.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately.
• If using a rebated slab ensure that all frame uprights are trimmed 25mm.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit
6mm drill bit
10mm drill bits
metal & masonry
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 3
COMPONENT PACKING LIST
FRAME PACK
QTY COMPONENT
DESCRIPTION
PART
No. CHK QTY COMPONENT
DESCRIPTION
PART
No. CHK
2BACK
WALL C2750 4 VERTICAL
DOOR BRACE C1555
12
ROOF &
SIDE WALL
BRACE
C2100 6 HORIZONTAL
DOOR BRACE K0640
6BOXING C0100 16 FRONT FR
CROSS BRACE K0285
2FRONT FR
HEADER C2300 4 FRONT FR
UPRIGHT C1785
2FRONT FR
UPRIGHT N1820 2 FRONT FR
RAFTER M1484
2FRONT FR
WEB C0240 2 PORTAL
RAFTER C1482
2PORTAL
COLUMN C1704
C Straight cut to both ends.
J20mm Tab notch on one end only
K20mm Tab notch on both ends
L45mm Lip notch on one end only
M45mm Lip notch on both ends
N20mm Tab notch + 45mm Lip notch
P20mm Tab notch + 45mm Lip notch on both ends
ROne end: 20mm Tab notch + 45mm Lip notch
SSPECIAL NOTCHING, not noted above.
FRAME SECTION IDENTIFICATION GUIDE
The first letter of the part number is used to identify the notching
type. EG. K2940, see below for reference list.
The following digits represent the overall length of the item.
EG. K2940
Part K2940 is a channel that is 2940mm long with a 20mm Tab notch
at each end.
20mm Tab
notch
45mm Lip
notch
20mm Tab
notch
+
45mm Lip
notch
4
5
4
5
2
0
2
0
2
0
C C
C
C
M
C
C
C
N
C
C
K
K
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 4
COMPONENT PACKING LIST
FITTINGS AND ACCESSORIES
QTY COMPONENT
DESCRIPTION
PART
No. CHK QTY COMPONENT
DESCRIPTION
PART
No. CHK
1INSTRUCTION
MANUAL IM 1
8G x 3/8” SELF
TAPPING SCREW
(220 PACK)
FAST001
2HINGE
6 HOLE FAST012A 8
3/16” x 1/2”
PAN HD
BOLT
FAST002
1
3mm POP
RIVET PACK
(50 PACK)
FAST009 83/16”
NYLOC NUT FAST003
24 MULTIPURPOSE
BRACKET (MPB) BKT17 3
10G x 5/8” WAFER
TEK SCREW
(300 PACK)
FAST014
1
DOUBLE DOOR
ANCHOR
BRACKET
BKT12 4PADBOLT FAST006
4CORNER
BRACKET BKT10 2PADBOLT
HASP FAST007
2
M10 DYNABOLT
M10 NUT & BOLT
BRACKET (8 PACK)
ANCHOR
KIT 4
DOOR
PLATE
2 CO + 2 ZINC
12A
1
SMALL
TRIANGULAR
PLATE
ZACO190 1PHILLIPS HEAD
DRIVER BIT FAST038
3
RIDGE
CONNECTOR
PLATE
ZACO9A 13MM DRILL
BIT DRILL
2KNEE
PLATE ZACO193 12 M10
DYNABOLT FAST015
2APEX
PLATE ZACO194 50 FAST033
HEX HD
TEK SCREW W/ NEO
WASHER 10-16x16mm
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 5
Single portal frame layout for REGENT models.
30372RK
30292RK
FRAMING OVERVIEW
• For ease of assembly front and portal frame shall be erected during initial construction of the
structure.
• Refer to FRONT FRAME ASSEMBLY for front frame specification.
*Portal frame dimension is taken from edge
of slab to centreline of portal frame.
Slab dimension specified in original manual.
Horizontal wall
framing is boxed.
Front frame is to be aligned with edge of slab rebate.
If there is no slab rebate inset it 75mm from edge of
slab.
1830mm* for 30372RK
1460mm* for 30292RK
C2750
FRONT FRAME
PORTAL FRAME
C2100
C2100
K0640
C1555
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 6
Frame layout for REGENT models.
30222RK
30142RK
23221RK*
23141RK*
FRAMING OVERVIEW
• For ease of assembly front and frame shall be erected during initial construction of the structure.
• Refer to FRONT FRAME ASSEMBLY for front frame specification.
C2100
C2100
C2750
K0640
C1555
Horizontal wall
framing is boxed.
*For 2.3m wide structures the following
parts will need to be cut to length.
C2750 to 2010mm
C2300 to 1560mm
M1484 to 1107mm, replicate ‘M’ notch.
C0240 to 145mm
Front frame is to be aligned with edge of slab rebate.
If there is no slab rebate inset it 75mm from edge of
slab.
FRONT FRAME
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 7
USING SELF DRILLING TEK SCREWS
Self drilling tek screws are an effective means of securing components without the need to pre-drill
holes. By following these instructions you will be able to easily secure your frame kit components.
Self drilling tek screws require an electric or battery
drill for installation, Do not attempt to fasten tek
screws by hand.
If available make sure that the drill has the slow
speed and high torque settings selected.
Fit the supplied driver bit into the chuck of the drill.
Place the tek screw onto the tip of the driver and
place the tek screw into position using the weight
of the drill to prevent it from moving.
Once in position apply a moderate amount of
pressure to the drill
Start slowly, begin to drill the tek screw into the
metal.
Once the tek screw has stabilised while drilling
increase the speed until the tek screw threads ‘bite’
into the metal.
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 8
NOTE:
- Only the horizontal wall frame sections are to be boxed.
- Do not screw any boxed sections until they have been correctly sized as the specific step instructs.
- Roof section, door frames and upright door studs are singular pieces.
- Use self drilling tek screws for all assembly and installation of these sections.
BOXING FRAME SECTIONS
1. All frame sections have one side length of
38mm and another at 40mm.
3. Slide opposing sides together so that
each frame section fits neatly inside the
other.
5. Fix with tek screws.
Use tek screws to fix the two sections and complete a boxed frame member as shown. Make sure that
you alternate tek screw position on opposing sides of the boxed sections. Align tek screws 296mm
apart. This is approximately 2 sheet corrugations in distance. If spaced correctly the screw heads will
line up with corrugations of the sheets and will make for a flush finish against the wall or roof.
2. Slide the 38mm side into the 40mm side
as shown.
4. Apply firm pressure to each side of the
boxed section to firmly lock it into position.
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 9
STEP 1 of 2
Refer to “BOXING
FRAME SECTIONS”
for further details
Box the following frame sections
together and fix with tek screws.
• C2300 + C2300 (x1)
• C0240 + C0240 (x1)
• C1785 + N1820 (x2)
Additional framing is supplied in this frame kit.
K0285 (x8) and C1785 (x2)
All other frame parts are supplied in the original shed kit.
NOTE: These frames will need to be trimmed by 25mm
to suit a rebated slab
FRONT FRAME ASSEMBLY (N3/C1)
C1785
C0100
C1785
N1820
C2300
M1484
ZACO190
ZACO9A
C0240
BKT17 K0285
BKT17
Absco Industries Assembly Instruction Manual
GABLE SHED
N3/C1 FRAME KIT
FOR REGENT MODELS
Model: CYCRK 02/02/21 1.2 10
STEP 2 of 2.
FRONT FRAME ASSEMBLY (N3/C1)
Fit one C0100 to box the
base of each outside leg
as shown. These will later
be used for securing the
frame to the concrete
slab.
Secure the small triangular
plate (ZACO190) to the
exterior side of the frame.
Secure the ridge
plate (ZACO9A) to
the interior side of
the frame.
325 325
2300*
1560**
1750
870
100
2045*
1980**
40mm all sections
* Dimensions for 3.0m wide models.
** Dimension for 2.3m wide models. To
achieve this parts must be trimmed as
described in FRAMING OVERVIEW.
193 193 193
Layout all sections as shown in the same
manner as a portal frame.
Use 16mm self drilling screws to join
all components together with three
screws at all connecting points on both
sides of the frame.
NOTE: These frames will need to be
trimmed by 25mm to suit a rebated
slab.
232232232
Table of contents
Other ABSCO SHEDS Outdoor Storage manuals
ABSCO SHEDS
ABSCO SHEDS PREMIER SHED User manual
ABSCO SHEDS
ABSCO SHEDS 30151SK User manual
ABSCO SHEDS
ABSCO SHEDS CYCWKUTK Installation guide
ABSCO SHEDS
ABSCO SHEDS 15151SK User manual
ABSCO SHEDS
ABSCO SHEDS 15231FK User manual
ABSCO SHEDS
ABSCO SHEDS REGENT 23221RK User manual
ABSCO SHEDS
ABSCO SHEDS 60303WK User manual
ABSCO SHEDS
ABSCO SHEDS SIGNATURE ADCPSN3 User manual
ABSCO SHEDS
ABSCO SHEDS CYC15 Installation guide
ABSCO SHEDS
ABSCO SHEDS 15141RK User manual
ABSCO SHEDS
ABSCO SHEDS PREMIER 15151GK User manual
ABSCO SHEDS
ABSCO SHEDS 15081SK User manual
ABSCO SHEDS
ABSCO SHEDS 23081SK-PTX User manual
ABSCO SHEDS
ABSCO SHEDS J30082SECO User manual
ABSCO SHEDS
ABSCO SHEDS J15231FK User manual
ABSCO SHEDS
ABSCO SHEDS 2314F1 User manual
ABSCO SHEDS
ABSCO SHEDS 23151SK User manual
ABSCO SHEDS
ABSCO SHEDS 30232GK User manual
ABSCO SHEDS
ABSCO SHEDS 3045UTK Installation guide
ABSCO SHEDS
ABSCO SHEDS CHICKEN COOP User manual
Popular Outdoor Storage manuals by other brands
Lifetime
Lifetime 6418 owner's manual
rollaway container
rollaway container ARPCA24 manual
Duratuf
Duratuf Havelock Assembly instructions
X-METAL
X-METAL 4065 owner's manual
Outdoor Life Products
Outdoor Life Products FP2030 F Assembly instructions
Royalcraft
Royalcraft Faro 295L Storage Box Assembly instructions
