ABB SACE Emax 2 E6.2 Manual
—
INSTRUCTION HANDBOOK
1SDH002306A1001 - ECN000285442
EMAX 2 E6.2
Disassembly instructions
3
Disassembly instruction emaX 2 e6.2
1. SCOPE
Scope of this document is to illustrate the step-by-step disassembly process of ABB SACE Emax 2 E6.2
air case circuit breaker equipped with an electronic trip unit (type Ekip TOUCH).
Document is focused on Emax 2 E6.2 3p IEC version, anyway it allows to cover other versions of Emax
2 E6.2 circuit breaker equipped with an electronic trip unit with just few slight differences to be taken
into account.
Gloves Glasses Safety shoes Protective clothes
4. TOOLS
Disassembly operations require the use of tools (e.g. screwdriver, torx key, pliers, …); tools to be used
are specified inside each phase of the disassembly process (see Chapter 6).
3. PERSONAL PROTECTIVE EQUIMENT (PPE)
When performing disassembly following safety Personal Protective Equipment (PPE) must be worn:
2. SAFETY NOTES
Before proceeding with any disassembly operation, it’s mandatory to put the circuit breaker in open
position and make sure that the springs of the operating mechanism are discharged.
For handling and lifting circuit breakers refer to section “Unpacking and handling” of Emax 2 “Installa-
tion, operation and maintenance instructions for the installer and the user” document. Improper lifting
can result in death, serious injury to persons and damage to the equipment; never lift a circuit breaker
above other people. The trained personnel in charge of handling and lifting must use appropriate safe-
ty equipment.
Disassembly operations of circuit breakers must be performed by qualified and skilled personnel in
the electrical field (IEV 195-04-01: person with relevant education and experience to enable him or her
to perceive risks and to avoid hazards which electricity can create) and having a detailed knowledge of
circuit breakers.
Disassembly activites must be performed in an ergonomic workspace able to ensure protection of per-
sons demanded to perform disassembly activities.
Applicable national legislation and international standards in force at the time of disassembly of circuit
breakers must be taken into account in addition to prescriptions illustrated in this document.
ABB declines any responsibility for injury to people or damage to property resulting from a failure to
comply with the instructions set out in this document and with any applicable safety standard.
4
INSTRUCTION HANDBOOK
Description Position inside circuit breaker Quantity
Base In sliding contacts block
Cover In sliding contacts block
Auxiliary position contacts cap In sliding contacts block
Right side wall In sliding contacts block
Flat cables assemblies In sliding contacts block
Connector cables assembly In sliding contacts block
Sliding contacts base In sliding contacts block
Ekip measuring blind module printed circuit board Mounted on the trip unit
Plug Mounted on the trip unit
Rating plug printed circuit board Mounted on the trip unit
Rating plug case Mounted on the trip unit
Mounted on the trip unit
Battery cover Mounted in the trip unit
Battery Mounted in the trip unit
Display printed circuit board Mounted in the trip unit
Display Mounted on the trip unit
Backplane Mounted on the trip unit
Trip unit case Mounted on the trip unit
Trip unit back cover Mounted on the trip unit
Trip unit printed circuit board Mounted in the trip unit
Mounted on the terminal box
Mounted in the terminal box
Connectors Mounted on the terminal box
Mounted on the terminal box
Mounted on the terminal box
Terminal box case Mounted on the terminal box
Left MID On the left part of the circuit breaker
CS adapter box Mounted on the upper cross beam
CS adapter printed circuit board Mounted inside CS adapter
CS adapter cover Mounted on the upper cross beam
CD block cover Mounted in the CD
Front of the CD Mounted on the CD
Position indicator Mounted in the CD
Feeler Mounted in the CD
CD block lever Mounted on the CD
Releases door Mounted on the MID
MID pawl Mounted on the MID
Spacers Mounted in the MID
MID reset lever Mounted in the MID
Mechanical reset anchor Mounted in the MID
Trip coil support base Mounted in the MID
5. SEPARATE TREATMENT
Table below lists parts requiring a separate treatment adding information about part location inside
circuit breakers and related quantity.
5
Disassembly instruction emaX 2 e6.2
If disassembled parts require a separate treatment a specific indication is provided inside each phase
with reason why for the separate treatment (see Chapter 6).
6. DISASSEMBLY PROCESS
Circuit breakers disassembly process is constituted by a sequence of operations to be performed on
products after their dismounting from original installation. For each phase following information are
provided:
applicable)
Description Position inside circuit breaker Quantity
Trip coil cover Mounted in the MID
Trip coil Mounted in the MID
Flat cover Mounted on the MID
Auxiliary flat assembly Mounted on the MID
RTC micro lever Mounted in the MID
MID main structure Mounted in the MID
Springs charging lever Mounted on the operating mechanism
Operating mechanism Mounted on the center of the circuit breaker
Auxiliary contacts cam Mounted on operating shaft assembly
Cam Mounted on operating shaft assembly
Lever Mounted on operating shaft assembly
Measuring module connector Mounted behind the trip unit and connected with poles
Protections Mounted in correspondence of rear terminals
Spacers Mounted in correspondence of rear terminals
Arc quenchings Mounted in arcing chambers
Spacers Mounted in arcing chambers
Sensors plugs Mounted in poles
Sensors Mounted in poles
Cables Mounted in poles
Insulating protection Mounted in poles
Insulation protection Mounted in poles
Contacts spacer Mounted in poles
6
INSTRUCTION HANDBOOK
Tools
Torx key
Flat screwdriver
6.1 PHASE 1 – CIRCUIT BREAKER FRONT COVER AND OPERATING
MECHANISM COVER
1
By means of the flat screwdriver turn of 90°
the 2 screws fixing the trip unit transparent
protection to the circuit breaker.
5
Manually remove the front cover.
6
By means of the torx key unscrew the 2 screws
fixing the 2 plugs to the front cover.
4
By means of the cross screwdriver unscrew the
4 screws fixing the front cover to the circuit
breaker main structure.
3
Manually remove the racking in and out lever
located in the bottom part of the circuit
breaker.
2
Manually remove the trip unit transparent
cover.
Actions to be performed
Cross screwdriver
No. 8
7
Disassembly instruction emaX 2 e6.2
7
Manually remove the 2 plugs.
8
By means of thr torx key unscrew the 2 screws
fixing the T.U. Reset assembly to the front
cover.
9
Manually remove the T.U. Reset assembly.
10
By means of the flat screwdriver remove the 2
benzings mounted on the T.U. Reset assembly.
11
By means of the flat screwdriver push the pin
as indicated by the arrow and after let the
the spring and the T.U. Reset signalling plug
automatically separate from the T.U. Reset
metal support.
12
By means of the torx key remove the 2 screws
fixing the plug to the circuit breaker front
cover.
8
INSTRUCTION HANDBOOK
13
Manually remove the plug.
15
By means of the cross screwdriver unscrew
the screw located on the side of operating
mechanism cover.
14
Manually push down the springs charging lever
and by means of the cross screwdriver unscrew
the 2 screws located behind the springs
charging lever fixing the operating mechanism
cover to the circuit breaker main structure
and always by means of the cross screwdriver
unscrew the screw located in the bottom right
part of the operating mechanism cover fixing
it to the circuit breaker main structure.
16
Manually complete the removal of the
operating mechanism cover.
9
Disassembly instruction emaX 2 e6.2
17
By means of the cross screwdriver unscrew the 4 + 4 + 4 screws fixing the left and the right
shields to the circuit breaker.
18
Manually remove the left shields.
19
Manually remove the right shield.
10
INSTRUCTION HANDBOOK
Disassembled parts
Metal)
Table of contents
Other ABB Circuit Breaker manuals
ABB
ABB SMISSLINE TP 2CCC451032M0109 User manual
ABB
ABB SACE Emax 2 User manual
ABB
ABB SACE Emax 2 User manual
ABB
ABB ADVAC 03 Installation and operating instructions
ABB
ABB SACE Emax 2 E2.2 User manual
ABB
ABB F-ARI Test Series User manual
ABB
ABB HD4/R User manual
ABB
ABB Emax 2 Retrofill AKR-30-800A Product manual
ABB
ABB SACE Tmax XT User manual
ABB
ABB Vmax User manual
ABB
ABB SACE Emax 2 E2.2 User manual
ABB
ABB VM1-T User manual
ABB
ABB SACE Emax 2 Manual
ABB
ABB SACE Emax 2 User manual
ABB
ABB SACE Emax Series Manual
ABB
ABB SACE Emax E1 User manual
ABB
ABB SACE Emax 2 - Tmax XT User manual
ABB
ABB Mechanism HMB-8 User manual
ABB
ABB AC500 V3 User manual
ABB
ABB Tmax MIR-V User manual
Popular Circuit Breaker manuals by other brands
Eaton
Eaton Power Defense PDG2 Instruction leaflet
Bticino
Bticino L4412CM2 quick start guide
Eaton
Eaton S-T0 Instruction leaflet
GE
GE EntelliGuard G Installation, operation and maintenance manual
OEZ
OEZ 3VA9-RS-4VBH1 Installation, service and maintenance instructions
Siemens
Siemens PSR Instructions, Installation, Operation, Maintenance