3D Systems Cubify CUBEX Duo User manual

1

CUBEX

Replacing a

Main Board

PCB

2

Contents

What you will need ..................................................................................................... 3

Removing the Case and floor panel. .......................................................................... 4

Removing the damaged Main Board PCB.................................................................. 6

Fitting the new Main Board PCB ................................................................................ 7

Re attaching the floor panel and case........................................................................ 8

3

What you will need

Replacement Main Board PCB

3mm Hex Driver

2.5mm Hex Driver

4

Before beginning this process please ensure that the print pad is raised to the

top of the machine, all cartridges and the jet wipe have been removed from the

machine and that you have made a note of your Z height and offset settings as

these settings will not be present on the new PCB. Unplug the CubeX from

mains power.

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

5

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

6

Removing the damaged Main Board PCB

Before removing the Main board PCB, label each of the looms that are plugged into

it. The PCB is marked to tell you which loom is plugged into which connector.

Remove the Looms and unplug the power supply from the main board PCB.

Gently pull up on the main board PCB to slide it off of the rubber ties holding it in

place.

7

Using the 2.5mm hex driver, undo the bolts holding the Print Jet driver boards to the

Main Board PCB and remove the Print Jet driver boards. (Note the amount of Print

Jet driver boards will correspond with the amount of Print Jets present on your

CubeX printer)

Fitting the new Main Board PCB

Plug the Extruder Driver boards into the new Main Board PCB and fasten with bolts.

8

Pull the rubber ties up through the holes on the main board PCB to fasten it to the

CubeX.

Plug the looms and power supply back into their corresponding connectors.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

9

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

10

You may now power up your CubeX.

You will need to re activate your CubeX using the activation code associated

with your CubeX. You will also need to re set your Z height and offsets, if you

did not make a note of these settings you can find instructions on how to set

them in the CubeX users guide.

Other manuals for Cubify CUBEX Duo

3

Table of contents

Other 3D Systems 3D Printer manuals

3D Systems

3D Systems ProJet 660Pro User manual

3D Systems

3D Systems Cube 2nd Generation User manual

3D Systems

3D Systems ProJet 1200 User manual

3D Systems

3D Systems ProJet 7000 User manual

3D Systems

3D Systems ProJet 4500 User manual

3D Systems

3D Systems ProJet 5500X User manual

3D Systems

3D Systems Viper Pro SLA User manual

3D Systems

3D Systems CubeX User manual

3D Systems

3D Systems projet mjp 2500 User manual

3D Systems

3D Systems SLA 750 Series User manual

3D Systems

3D Systems ProX User manual

3D Systems

3D Systems ProX DMP320 User manual

3D Systems

3D Systems iPro 8000 SLA Center User manual

3D Systems

3D Systems ProJet 5000 User manual

3D Systems

3D Systems Figure 4 Standalone User manual

3D Systems

3D Systems ProX DMP 100 User manual

3D Systems

3D Systems PostCure 1050 User manual

3D Systems

3D Systems ProJet SLA 6000 User manual

3D Systems

3D Systems CUBE User manual

3D Systems

3D Systems DuraForm TPU Elastomer User manual

3D Systems

3D Systems ProJet 4500 User manual

3D Systems

3D Systems ProX DMP 100 User manual

3D Systems

3D Systems Cube 3rd Generation User manual

3D Systems

3D Systems Allevi 3 User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

Stratasys

Stratasys J850 user guide

MakerBot

MakerBot Replicator user manual

Stratasys

Stratasys FDM Vantage Series user guide

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide