3D Systems CubeX Assembly instructions

Print Tip Replacement

Your CubeX 3D printer

Print tip replacement

So you are the owner of a CubeX and you have to replace a print tip? We have gathered information from

what you need to how to do the print tip change.

What you need:

Print tip assembly

2.5mm hex driver

Pliers

Before beginning this process please remove all filament from the print jets and check that your

print pad is level. For instructions on how to do this please refer to theCubeX user guide.

REMOVING THE DAMAGED PRINT TIP

Turn off the CubeX and Unplug it from the mains power.

Unplug the print tip from the Print jet sensor board and feed the wire down the hole to the print tip.

Unfasten the print tip holding bolt.

The print tip and print jet are assembled by sliding the print tip into the print jet and twisting it (as

pictured).

To remove the print jet you will need to twist it and pull down, eventually you will find the correct

orientation and the print tip should easily slide out.

INSTALLING THE NEW PRINT TIP

Feed the print tip wires up through the print jet carriage and plug them into the Print Jet sensor board.

Slide the new print tip into the print jet and turn it until the print tip wires are orientated to travel straight up

to the Print Jet sensor board.

LEVELING THE PRINT TIPS FOR CUBEX DUO/TRIO

For a single print jet please see Fastening the print tip on a CubeX.

Power on the CubeX printer.

To clean the nozzles for levelling, put the CubeX printer into PJ-Control mode. Heat all of the print jets

EXCEPT for the new one to 230° and clean of any plastic debris with pliers. Allow the Print Jets to cool

down.

Put the CubeX printer into manual move mode.

Raise the print pad until it is approximately 5mm away from the print tips.

Slowly raise the print pad until it lifts the new print tip in line with the others. All three print tips should be

touching the bed without putting any pressure on it.

Turn the CubeX printer off and unplug it from the mains power supply.

Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print tip in place.

With the print tips levelled you can now turn on the CubeX printer and set the print tip offsets.

SETTING PRINT TIP OFFSETS

See the CubeX user guide for instructions on how to set your print tip offsets.

Download the CubeX Duo calibration file

Download the CubeX Trio calibration file

FASTENING THE PRINT TIP ON A CUBEX

A CubeX with a single print jet does not have a second or third nozzle to reference the print tip level.

Instead you have to use the CubeX wiping stick.

Power on the CubeX printer.

Put the CubeX into manual move.

Raise the print pad until it is approximately 5mm away from the print tip.

Slowly raise the print pad until the print tip is touching it.

Continue raising the print pad until there is approximately 0.5mm between the print pad and the CubeX

wiping stick.

Turn the CubeX printer off and unplug it from the mains power supply.

Using the 2.5mm hex driver, tighten the print tip holding bolt (pictured) to lock the print jet in place.

With the print tip fastened you can now turn on the CubeX printer and start printing.

Other manuals for CubeX

This manual suits for next models

Table of contents

Other 3D Systems 3D Printer manuals

3D Systems

3D Systems 3D Sprint User manual

3D Systems

3D Systems CUBE User manual

3D Systems

3D Systems ProX 950 User manual

3D Systems

3D Systems ProJet 1200 User manual

3D Systems

3D Systems CubePro User manual

3D Systems

3D Systems SLA 750 Series User manual

3D Systems

3D Systems ProX DMP 100 User manual

3D Systems

3D Systems ProJet 4500 User manual

3D Systems

3D Systems Geomagic Touch User manual

3D Systems

3D Systems Cube 3rd Generation User manual

3D Systems

3D Systems Viper Pro SLA User manual

3D Systems

3D Systems wematter Atmosphere User manual

3D Systems

3D Systems CubePro Parts list manual

3D Systems

3D Systems ProJet SLA 6000 User manual

3D Systems

3D Systems CubePro User manual

3D Systems

3D Systems ProJet 6000 User manual

3D Systems

3D Systems ProX 800 User manual

3D Systems

3D Systems ProX DMP 300 User manual

3D Systems

3D Systems CUBE User manual

3D Systems

3D Systems ProJet 5000 User manual

3D Systems

3D Systems ZPRINTER 650 User manual

3D Systems

3D Systems ProJet 1200 User manual

3D Systems

3D Systems ProJet MJP 5600 User manual

3D Systems

3D Systems CUBE User manual

Popular 3D Printer manuals by other brands

Ultimaker

Ultimaker S5 Material Station installation guide

EcubMaker

EcubMaker TOYDIY quick start guide

AnyCubic

AnyCubic Kossel Plus Modification

ReDeTec

ReDeTec ProtoCycler Operation manual

Kywoo3D

Kywoo3D Tycoon IDEX user manual

CraftBot

CraftBot PLUS PRO user guide

3DGence

3DGence INDUSTRY F340 user manual

HP Jet Fusion 4200 Product Documentation Site Preparation Guide

Rokit

Rokit AEP Series user manual

AnkerMake

AnkerMake M5 user manual

DIYElectronics

DIYElectronics PRUSA I3 ELECTRONICS AND SOFTWARE GUIDE

Ackuretta

Ackuretta FreeShape 120 user manual

LONGER

LONGER LK5Pro manual

Stratasys

Stratasys J850 user guide

MakerBot

MakerBot Replicator user manual

Stratasys

Stratasys FDM Vantage Series user guide

ZYYX

ZYYX Pro II user manual

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Startup guide