8
Adjustment of the required temperature or time:
The require temperature or time in the metho s (menu) THERMOSTAT, CALIBRATION an PROFILE are a juste by
pressing keys plus + (to increase the value) or minus – (to ecrease the value). First the require value is change of
tenths of egree or 1 secon s, after ten changes (ten presses of key) the require value is change of egrees or 10
secon s, after ten following changes (ten presses of key) the require value is change of 10 egrees or 100 secon s
etc. Once you have a juste the require ata push the key OFF to save it into the memory, after this step the text
THERMOSTAT appears again on the isplay.
Metho Thermostat:
This algorithm allows to a just any require temperature an the Water Bath maintains the temperature for the
require time. The evice has save the last value a juste temperature that was regulate . If you o not want to
change the value of the temperature start the algorithm itself by pressing the key ON. The text: REQ.CONTROL:
appears on the first line of the isplay, there is the time in minutes „min=“an the real temperature „T=“ in
0
C
on the
secon line.
If the set temperature oesn’t suit you an you nee to change it you have to a just the require temperature before
you press the key ON. The require temperature is set with the help of keys plus + (to increase the value) or minus –
(to ecrease the value) – see the paragraph above: Adjustment of the required temperature or time: in the chapter
Contro a gorithms. After setting the require temperature press the key OFF an in that way the require
temperature is save an the text THERMOSTAT appears again on the isplay. Now you can start the temperature
control running by pressing the key ON. The algorithm is stoppe by pressing the key OFF. If there is not enough
water in the Bath the text „add water“ appears automatically on the isplay an it will isappear once the water is
a e .
Method PROFILE:
This algorithm allows to a just any require time behaviour of temperatures. It is possible to a just as many as 7
points efine with time an temperature coor inates. After choice of the item PROFILE in the main menu with the
help of the key ROTATION one can start the algorithm itself by pressing the key ON.
After 1 sec the text: START ON:
OTHER PARAMETERS: appears on the isplay.
If there has been alrea y set the temperature curve before, one can use it again (because it is save in the internal
memory) by hol ing the key ON at the time when the text: START ON:
OTHER PARAMETERS: appears on the isplay.
If there hasn’t been set the temperature curve yet or it is necesary to set it in a ifferent way, one waits about 1 sec
till the text SET UP THE CURVE appears on the isplay. After that the text: time of point 1= appears on the first line an
one sets the time in minutes on the secon line. Time is set with the help of keys plus + (to increase the value) or
minus – (to ecrease the value) – see paragraph: A justment of the require temperature or time: in the chapter
Control algorithms. After setting the time of point 1 press the key OFF an in that way time of point 1 is save in the
internal memory an after that the text: time of point 2= appears on the first line an one sets in the same way the
time of point 2, the time of point 3, the time of point 4, the time of point 5, the time of point 6, the time of point 7.
After setting the time of point 7 press the key OFF an the text: temp. of point 1= appears on the first line an one
sets the temperature in
c
C. on the secon line. Temperature is set with the help of keys plus + (to increase the value)
or minus – (to ecrease the value) – see paragraph: A justment of the require temperature or time: in the chapter
Control algorithms. After setting the temperature of point 1 press the key OFF an in that way temperature of point 1
is save in the internal memory an after that the text: temp. of point 2= appears on the first line an one sets in the
