ZyXEL Communications ZyWALL 1050 User manual
2
ENGLISH
1 Checking the Package Contents
2 Rack-mounted Installation
Mount the ZyWALL in a 19-inch rack or place it on a sturdy, flat surface.
Note: Leave 10 cm of clearance at the sides and 20 cm in the rear.
1Align one bracket with the holes on one side of the ZyWALL and secure it with the included bracket
screws. Similarly, attach the other bracket.
2After attaching both mounting brackets, position the ZyWALL in the rack by lining up the holes in the
brackets with the appropriate holes on the rack. Secure the ZyWALL to the rack with the rack-mounting
screws.
Your package should
include one of each
of the following:
• ZyWALL 1050
•Powercord
• Rack-mounting kit
• RJ-45 Ethernet cable
• RS-232 console Y-cable
• Printed Quick Start Guide
• Configuration Reference Card
• Compact disk (CD)
ENGLISH
3
3 Connecting the Hardware
Make sure that the power switch on the rear panel is turned off before you make the hardware connections.
1It is recommended that you configure the ZyWALL before using it to protect your network. Use an Ethernet
cable to connect a computer to port 1.
2Use another Ethernet cable(s) to connect port 2 and/or port 3to an Ethernet jack with Internet access.
3Use the included power cord to connect the power socket on the rear panel to a power outlet.
4Push the power switch to the on position and look at the front panel. The PWR light turns on. The SYS light
blinks during system testing and initialization and then stays on when the system is ready.
4 Web Login
1Launch your web browser and go to http://192.168.1.1 (the
ZyWALL automatically redirects you to https://
192.168.1.1).
ENGLISH
4
2Click Yes to proceed if you get a security alert or
certificate screen.
3Enter admin as the user name and 1234 as
the password. Click Login.
4It is strongly recommended that you change the
password. Type and retype a new password, and click
Apply.
ENGLISH
5
5 Installation Setup Wizard
Use an installation setup wizard to connect to the Internet and register the ZyWALL and/or activate trial
services, like IDP and content filter.
Note: Use the installation wizard only for initial configuration starting from the default configuration.
Changes you make in the installation wizard may not be applied if you have already changed the
ZyWALL’s configuration.
The Status screen
opens. Click the
Wizard icon in the
upper right corner.
•INSTALLATION SETUP, ONE ISP sets up a sin-
gle Internet connection for ge2.
•INSTALLATION SETUP, TWO ISP sets up Inter-
net connections for ge2 and ge3.
ENGLISH
6
6 Default Settings and Port Details
The ZyWALL is configured for the following network topology by default.
The wizard screens vary depending on the
encapsulation type you use. Refer to information
provided by your ISP and the web help screens to
know what to enter in each field. You can leave fields
blank if you don’t have that information.
ENGLISH
7
Note: The USB ports, extension card slots, and hard disk slot are reserved for future use.
7 Troubleshooting
Port Interface Zone IP Address and DHCP Settings Suggested Use With Default Settings
1ge1 LAN 192.168.1.1, DHCP server enabled Protected LAN
2, 3ge2, ge3 WAN DHCP clients Connections to the Internet
4, 5 ge4, ge5 DMZ None, DHCP server disabled Public servers (such as web, e-mail and
FTP)
DIAL BACKUP aux None None Auxiliary modem
CONSOLE N/A None None Local management
Label Type Cable to Use
1~5 RJ-45 8-wire Category 5e or above Ethernet cable
DIAL BACKUP, CONSOLE RS-232 RS-232
Problem Corrective Action
None of the LEDs
turn on.
Make sure that you have the power cord connected to the ZyWALL and plugged in to an
appropriate power source. Make sure you have the ZyWALL turned on. Check all cable
connections.
If the LEDs still do not turn on, you may have a hardware problem. In this case, you should
contact your local vendor.
ENGLISH
8
8 Procedure to View a Product’s Certification(s)
1Go to www.zyxel.com.
2Select your product from the drop-down list box on the ZyXEL home page to go to that product's page.
3Select the certification you wish to view from this page.
Cannot access
the ZyWALL from
the LAN.
Check the cable connection between the ZyWALL and your computer or switch. Refer to
section 3 for details.
Ping the ZyWALL from a LAN computer. Make sure your computer’s Ethernet card is
installed and functioning properly. Also make sure that its IP address is in the same subnet
as the ZyWALL’s.
In the computer, click Start, (All) Programs, Accessories and then Command Prompt. In
the Command Prompt window, type "ping" followed by the ZyWALL’s LAN IP address
(192.168.1.1 is the default) and then press [ENTER]. The ZyWALL should reply.
If you’ve forgotten the ZyWALL’s password, use the RESET button. Press the button in for
about 5 seconds (or until the PWR LED starts to blink), then release it. It returns the ZyWALL
to the factory defaults (password is 1234, LAN IP address 192.168.1.1 etc.; see your User’s
Guide for details).
If you’ve forgotten the ZyWALL’s IP address, you can use the commands through the
console port to check it. Connect your computer to the CONSOLE port using a console
cable. Your computer should have a terminal emulation communications program (such as
HyperTerminal) set to VT100 terminal emulation, no parity, 8 data bits, 1 stop bit, no flow
control and 115200 bps port speed.
Cannot access
the Internet.
Check the ZyWALL’s connection to the Ethernet jack with Internet access. Make sure the
Internet gateway device (such as a DSL modem) is working properly.
Check ge2’s status in the Status screen. Use the installation setup wizard again and make
sure that you enter the correct settings.
Problem Corrective Action
9
DEUTSCH
1 Prüfen des Packungsinhalts
2 Rackmontage
Montieren Sie die ZyWALL an einem 19"-Rack oder stellen Sie es auf eine stabile Unterlage.
Hinweis: Lassen Sie seitlich 10 cm und hinten 20 cm Platz.
1Richten Sie eine Halterung an den Löchern an der Seite der ZyWALL aus und schrauben Sie sie mit den
mitgelieferten Montageschrauben fest. Verfahren Sie ebenso mit der zweiten Halterung.
2Wenn Sie beide Montagehalterungen befestigt haben, richten Sie die ZyWALL im so im Rack aus, dass
die entsprechenden Schraublöcher übereinander stehen. Befestigen Sie den ZyWALL mit den
Befestigungsschrauben am Rack.
Prüfen Sie ob alle
Teile vorhanden
sind:
• ZyWALL 1050
• Netzkabel
• Rackmontage-Zubehör
• RJ-45-Ethernetkabel
• Y-Kabel für RS-232-Konsole
• Kurzanleitung in Druckform
• Konfigurationskarte
•CD
DEUTSCH
10
3 Anschließen der Hardware
Stellen Sie sicher, dass der Netzschalter an der Rückseite des Geräts ausgeschaltet ist, bevor Sie die
ZyWALL in Betrieb nehmen.
1Es wird empfohlen, die ZyWALL zu konfigurieren, bevor Sie sie zum in Ihrem Netzwerk einsetzen.
Schließen Sie einen Computer mit einem Ethernetkabel an Port 1 an.
2Schließen Sie an Port 2 und/oder Port 3Ihren Router mit Internetzugriff an.
3Schliessen Sie den Netzanschluss des Geräts (an der Rückseite) mit dem mitgelieferten Netzkabel an
eine Netzsteckdose an.
4Schalten Sie den Ein/Aus-Schalter in die Position On und sehen Sie sich das vordere Bedienfeld an. Die
PWR-LED beginnt zu leuchten. Die SYS-LED blinkt während des Systemtests und der Initialisierung, und
sie leuchtet, wenn der Test abgeschlossen und das System bereit ist.
4 Anmelden im Internet
1Starten Sie Ihren Internetbrowser und rufen Sie die Seite
http://192.168.1.1 auf (der ZyWALL leitet Sie automatisch
zur Seite https://192.168.1.1 weiter).
Other manuals for ZyWALL 1050
10
Table of contents
Languages:
Other ZyXEL Communications Firewall manuals
ZyXEL Communications
ZyXEL Communications ZyWALL 1100 Series User manual
ZyXEL Communications
ZyXEL Communications ADSL 2+ Security Gateway User manual
ZyXEL Communications
ZyXEL Communications ZyXEL ZyWALL 5 Manual
ZyXEL Communications
ZyXEL Communications ADSL 2+ Security Gateway Instruction Manual
ZyXEL Communications
ZyXEL Communications ZyWALL 1050 Reference guide
ZyXEL Communications
ZyXEL Communications ZyWALL 1050 Instruction Manual
ZyXEL Communications
ZyXEL Communications ZYWALL 2 WG User manual
ZyXEL Communications
ZyXEL Communications ZyWALL 1050 User manual
ZyXEL Communications
ZyXEL Communications ZyXEL ZyWALL IDP 10 Manual
ZyXEL Communications
ZyXEL Communications ZyWALL/USG Series User manual
ZyXEL Communications
ZyXEL Communications ZyXEL ZyWALL IDP 10 User manual
ZyXEL Communications
ZyXEL Communications ZyWALL 1050 Manual
ZyXEL Communications
ZyXEL Communications ZyWALL SEM-DUAL User manual
ZyXEL Communications
ZyXEL Communications ZyWALL 1050 Instruction Manual
ZyXEL Communications
ZyXEL Communications ZYWALL 1050 - V1.00 EDITION 1 User manual
ZyXEL Communications
ZyXEL Communications ENTERPRISE NETWORK CENTER User manual
ZyXEL Communications
ZyXEL Communications ZyXEL Prestige 310 User manual
ZyXEL Communications
ZyXEL Communications ADSL 2+ Security Gateway User manual
ZyXEL Communications
ZyXEL Communications ZyWALL SSL 10 User manual
ZyXEL Communications
ZyXEL Communications ZyXEL ZyWALL 35 User manual
