ZKTeco LH3000 User manual

Table of contents

Popular Lock manuals by other brands

Magic

Magic 105 manual

Gantner

Gantner GAT NET.Lock 7020 System Installation, configuration & operation

Wittkopp

Wittkopp Insys 7202 manual

Dorma

Dorma Studio Classic Installation instruction

Securam

Securam ECSL-601 quick start guide

Sudhaus

Sudhaus 3003 operating manual

Safety 1st

Safety 1st 48517 user guide

Pado

Pado FDS-10 user manual

Esco

Esco systeQ Series installation instructions

COMPX

COMPX National D8951 instruction sheet

secureo

secureo Key Box instruction manual

Stock Loks

Stock Loks C8713 instruction sheet

COMPX

COMPX 1T-058 Information

Auslock

Auslock T11 user manual

ELCOM

ELCOM 7205 Operating instruction

Stealth SAFES

Stealth SAFES ShadowVault Instructions & Troubleshooting

Knox

Knox KeySecure 5 Admin & user guide

Kwikset

Kwikset 48334/01 Quick installation guide

Installation Instruction

Version: 1.0

Date: Nov. ,2016

LH3000

B

A

C

D

E

H

F

G

L

E

M

P

Diagram

Before Installation

1

I

J

QN

O

K

J

I

Q

C

F

PackingList

2

D

G

20 mm

H

B

A

45 mm

E

40 mm

P

67mm

LM

O

N

5.5mm

3

Door Preparation

1. Check door thickness, prepare the proper screws and spindles.

Note: Please install the mortise (F) and strike plate (L) according to the above pictures.

L

L

L

L

FF

FF

Left inward Right inward

Left outward Right outward

2. Check door open direction.

Door Thickness E Spindles R Screws P Spindle

35-55 mm 40 mm 45 mm 67 mm

Note: If out of the door thickness of 35-55 mm,this lock will not be available.

4

Cautions

1. New lock is defined as always open mode until it was unlocked once by mifare card.

2. Please swipe authorised card,time sync card,room card at first for the new lock.

3. The lock is equipped with mechanical keys for manual unlocking. Remove the

mechanical keys from the package and keep them in a safe place.

4. To power on the lock, four alkaline AA batteries (not included) are required.

Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

5. Do not remove batteries when the lock is in working state.

6. When battery power is low, the lock will beep to remind user to renew the batteries.

Please do not mix up positive and negative while replacing battery.

7. Avoid contacting with corrosive substances, and do not hang objects on the handle.

8. The software within the lock manages the RFID cards, for more details refer to the

software user manual.

9. If there are any questions, please do not hesitate to contact the seller.

Installation

5

desired handle

height

center line of

the handle

door thickness

35~55 mm

backset

62.5 mm

2. Remove the mortise latch plate (H)

1. Drill holes on the door

Note 1: Align the template along the vertical

center line of the mortise (F) at the desired

handle height, and tape it to door.

Note 2: Mark the holes first, then start drilling.

F

H

I

J

6

3. Install mortise (F)

G

G

F

Note: Ensure the two triangles are in horizontal alignment.

D

N

O

ON

4.Install lock cylinder (D)

D

N

7

5.Install spindle (E)

E

E

6.Install outdoor unit (C)

E

C

C

8

7.Install spindle (E) and (P)

E

P

E P

Q

A

8.Install indoor unit (Q)

E

P

A

Q

9

9.Install the battery (K) and mortise latch plate (H)

K

J

I

H

I