Zeta ZT50410 User manual
ZT50410
Pocket Jump Starter
1
A. Introduction:
Whether you use the Pocket Jump Starter
for jump starting your vehicle, ATV,
Motorcycle, or boat; you can be sure the
Pocket Jump Starter will be ready to go
wherever and whenever you need it.
What's Included
Pocket Jump Starter
4 in 1 USB Cable
Smart Jumper Cable with Clamps
110V Wall Outlet Charger
12V Car Charger
Carrying Pouch
Table of Contents
What's Included.....................................................1
Introduction............................................................1
General Safety Information...............................2
Product Layout......................................................5
Operation Guidance............................................6
-Battery Indicator...............................................6
-Recharging Battery..........................................6
-Jump Starting a Vehicle................................. 7
-Charging Portable Devices.........................10
-LED Flashlight................................................. 10
Lithium Battery Caring Tips............................ 11
FAQ..........................................................................12
Troubleshooting.................................................13
Warranty................................................................15
Environmental Protection.............................. 16
Technical Specifications...................................16
2
General Safety Information:
Do not expose the pocket jump starter to rain, moisture or any liquid. Exposure to liquid or
moisture may cause the pocket jump starter to fail and increase the risk of electrical shock or
fire. Do not use this pocket jump starter if it should become wet. Make sure this pocket jump
starter is insulated from water if you have to use it in the rain or snow.
Do not expose the pocket jump starter to open flame, such as candles, camp re, etc.
Under no circumstances should the users make any change or modication to the product
or its accessories. Any changes made may compromise safety, aect the performance of the
product and void the warranty.
In case the battery begins to leak, do not allow your body parts to come in contact with the
liquid. If contact has been made, please wash with plenty of water and seek medical advice.
Do not expose the product to excessive heat, such as inside a car under direct sunlight
where temperature may exceed 140°F (60°C) degrees. Battery under extreme heat may
generate more heat, rupture, or ignite. Storing the pocket jump starter under such
condition may result in degradation of performance and shorter battery life.
The pocket jump starter contains lithium batteries, please dispose the pocket jump starter
properly, following local regulations. Do not incinerate.
3
Caution:
Make sure that you plug in the jump starter socket fully before trying to jump start the
vehicle. If not, there is a chance that you cannot jump start your vehicle and melt the
connection in the plug at the same time
Before jump starting your vehicle, make sure the battery clamps are securely connected,
clean the battery terminal if it appears to be corroded, or dirty. Do not attempt to jump start
the vehicle after 3 unsuccessful tries, otherwise, you may damage the pocket jump starter.
You may need to look into other causes that prevent the engine from starting up. (Engine
cranks over, but does not re)
Please disconnect the battery clamp after the vehicle has been started, if you leave the
battery clamp connected for more than 30 seconds, you may cause damage to the jump
starter.
Do not connect the 2 clamps directly with each other during override mode, you will short
the circuit and cause damage to the jump starter and personal injuries.
When the smart battery clamp beeps, please disconnect it from the battery.
4
Always exercise care when you are using this jump starter.
This pocket jump starter is not intended for use by children.
Do not use this pocket jump starter in an explosive environment, such as in the presence of
ammable liquid, gases or combustible dust.
Do not modify or disassemble this pocket jump starter, only a certied tech may perform
repair on this device.
Do not expose this pocket jump starter to extreme temperatures, or under prolong sun
exposure. Operating temperature for this device is -20°C ~ 60°C or -4°F ~ 140°F, also only
charge this pocket jump starter within the above prescribed ambient temperature.
Recharge this pocket jump starter with the AC charger included in this kit to avoid damage
to the electronic components.
Under extreme conditions, battery leakage may occur, carefully wipe the liquid off of the
device and avoid skin contact, in case of skin or eye contact, rinse with water immediately
and seek medical attention.
5
A. PRODUCT LAYOUT:
Switch
Jump start socket
Charging Port
USB 5V 2A
LED flash light
Battery
Indicator
6
B. OPERATION GUIDANCE
Battery Indicator
Press the switch to check the battery level. The number shown
indicates the remaining battery capacity.
Recharging the pocket jump starter:
Using the 110V wall outlet:
1. Plug in the charger included into the wall outlet.
2. Connect the charger to the charging port on the pocket jump starter.
Using the 12V car charger:
1. Plug in the 12V charger adapter to the vehicle’s 12V socket
2. Connect the charger to the charging port on the pocket jump starter.
7
For jump starting a vehicle with 12 volt battery system:
Check the battery level before jump starting the vehicle. It is recommended to
recharge the battery before jump starting a vehicle if the battery level is below 50%.
1
Connect the red battery clamp of the jumper cable to the vehicle’s positive (+)
terminal and connect the black battery clamp of the jumper cable to the vehicle’s
negative (-) terminal.
2
OVERRIDE
POWER
+
+
Note 1: This jump starter will start gasoline engines in passenger vehicles, pickup trucks, and
diesel engine vehicles with less than 3.0 liter displacements.
8
a.) Plug in the Smart battery clamp to the jump starter socket. Press and hold the power
button on the controller until the blue indicator comes on. Then start your engine.
b.) If a car battery is not present or
completely dead (disconnect the dead
battery before jump start), you can
activate the override by pressing and hold
the "override" button for 4 seconds, then
you have 30 seconds to start the engine.
3
OVERRIDE
POWER
POWER OVERRIDE
OverridePower
9
When the engine starts, disconnect the jumper cable from the pocket jump starter and
battery terminals within 30 seconds.
5
OVERRIDE
POWER
+
OVERRIDE
POWER
Leave the engine running.
Note 2: If the voltage is too low on the car battery, you may need to disconnect the cables from your car
battery. Then connect the car’s power cable directly with the jumper cable, and start the engine.
Once the engine is running, carefully place the power cables back onto the car battery.
6
Table of contents
