Zennio Z41 COM User manual

Z41 COM + GetFace IP

Configuration Guide

CONFIGURATION GUIDE

Application Program Version Z41 COM: [1.2]

GetFace IP Firmware Version: [2.26]

User manual version: c

www.zennio.com

 Z41 COM + Zennio GetFace IP Configuration Guide 
http://www.zennio.com Tecnical Support:http://support.zennio.com 
 

CONTENTS 
Contents ...................................................................................................................................2 
Document Update ....................................................................................................................3 
Introduction ......................................................................................................................4 
Basic Configuration ...........................................................................................................6 
1 Z41 COM Configuration ................................................................................................6 
2 GetFace IP Configuration ..............................................................................................9 
Advanced Configuration..................................................................................................13 
1 System with multiple Z41 COM...................................................................................13 
1.1 Z41 COM Configuration.......................................................................................13 
1.2 GetFace IP Configuration.....................................................................................14 
2 System with multiple GetFace IP: Phone Number (ID).................................................16 
2.1 Z41 COM Configuration.......................................................................................16 
2.2 GetFace IP Configuration.....................................................................................17 
3 Doors..........................................................................................................................18 
3.1 Z41 COM Configuration.......................................................................................18 
3.2 GetFace IP Configuration.....................................................................................19 
 

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

DOCUMENT UPDATE

Version

Modifications

Page(s)

- Changes in Z41 COM: do not affect this

document.

- Changes in GetFace IP: change in the

indicated configuration of the system API.

- Changes in Z41 COM: tabs and parameters

reorganization.

- Changes in GetFace IP: do not affect this

document.

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

1INTRODUCTION

This document presents an example of basic configuration of the GetFace IP video

intercom together with the indoor unit Z41 COM in a simple installation of a private

home when both devices are in the same network. A compiter conected to the same

network is also required to access to the GetFace IP web interface configuration.

Figure 1 shows an example of installation and IP addresses of each device.

Figure 1 Topology

It should be noted that Z41 COM has two IP addresses:

One for (in the example: 192.168.1.100)

Remote control through Z41 Remote application.

Connection with the NTP server to update date and time.

Firmware updating through Z41 Update.

Another one for the communication with the video intercom. In the example:

192.168.1.101.

In this case only the IP for the video intercom communication needs to be set,

taking into account that it must not be the same as the IP for the remote control.

Z41 COM

GetFace IP

Internet

Router

192.168.1.103

192.168.1.101

192.168.1.100

192.168.1.102

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

Important: these IP addresses of Z41 COM are managed independently, so it is not

required that both belong to the same IP network.

It is recommended to configure both devices in parallel since it is important that certain

parameters have the same values in both devices (this is indicated with warning notes

throughout the document).

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

2BASIC CONFIGURATION

This section shows the basic configuration required in an installation with a single Z41

COM unit and a single GetFace IP unit.

Note: For further information about the parameters please refer to the Z41 COM or

GetFace IP user manuals available at the Zennio website (www.zennio.com).

2.1 Z41 COM CONFIGURATION

The following aspects must be configured in the ETS configuration (default values in

blue, modified values in red):

1. In “MAIN CONFIGURATION”, tab “VoIP Calls”:

1.1. IP Address: 192.168.1.101 (the default value can be left).

1.2. Subnet Mask: 255.255.255.0

1.3. Specify Gateway: Disabled. (not necessary if the devices are in the same

network).

1.4. Video Intercom: Enabled.

Figure 2 Z41 COM –VoIP Calls Configuration.

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

IMPORTANT: If the IP for the remote control of Z41 COM is set statically in

“MAIN CONFIGURATION”, tab “Ethernet” make sure not to set the same IP for

the VoIP Calls.

2. In “Video Intercom”:

2.1. Outdoor Unit 1: Enabled.

3. In “Outdoor Unit 1”, in the tab “Configuration”:

3.1. Type: Private.

The private type allows accessing at any time to the visualization of images

from the camera of the outdoor unit. The community type does not

3.2. The Outdoor Unit Is in a Different Network: Disabled.

In our example, the video intercom unit is located on the same network:

192.168.1.0/24.

3.3. Define ID: Disabled.

The ID only needs to be indicated when there are several external units and

want to associate them with different video intercom boxes in Z41 COM. See

section 3.1 for further information.

3.4. Number of Doors: 1.

In our example, the system will have a single access with a single door.

3.5. Opening Settings:

3.5.1. HTTP Command: Enabled.

3.5.2. Secure Opening: Disabled.

3.5.3. KNX Object: Disabled.

3.6. Automatic Door Opening: Disabled.

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

Figure 3 Z41 COM –Outdoor Unit Configuration.

4. In “MENU” enable a page and within it box whit Visualization “Other” and function

“Video Intercom”.

Figure 4 Z41 COM - Video Intercom box configuration.

4.1. Video Intercom: 1.

IMPORTANT: the number of the video intercom must be the same as the one

selected in 1.4.

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

2.2 GETFACE IP CONFIGURATION

By default GetFace IP acquires its IP address by DHCP, but it can be set a static IP

address as well. To change between one mode and another follow the steps below:

1. Connect GetFace IP to the power supply and to the network.

2. After connecting the power supply or after performing a reset and once the video

intercom is fully initialized (wait until lights up permanently), there are 30 seconds of

operation to perform the following actions:

2.1. Press for 5 times the button of the basic

unit: the device announces its IP.

2.2. Press for 15 times the button of the basic

unit: the device will switch between a

dynamic IP (DHCP) and a static IP

configuration.

The default static IP configuration is shown in Figure 5.

Figure 5 GetFace IP - Static IP Configuration by default

It is recommended to set the IP assignment by DHCP (later is possible to change it to a

static IP) to be able to access the web configuration interface.

To access to the configuration interface, enter the video interdom IP in a web browser.

For example: http://192.168.1.100.

Authentication is required for access to the web interface. By default, it is set to:

Main button

Z41 COM + Zennio GetFace IP Configuration Guide

http://www.zennio.com Tecnical Support:http://support.zennio.com

Username: admin

Password: zennio

Changing the password is recommended after the first access to the device. The main

window will look similar to Figure 6. The default language of the interface is English. It

can be changed in the upper right.

Figure 6 GetFace IP - Configuration menu

First, if wanted to change the IP address to a static configuration (this step is not

mandatory, the IP assigned by DHCP can be left):

1. System Network

1.1. Use DHCP Server: Disabled.

1.1.1. Set the network configuration desired.

Other manuals for Z41 COM

This manual suits for next models

Table of contents

Popular Touch Panel manuals by other brands

FlowLine

FlowLine Data loop quick start

ALPEX

ALPEX AEx-8 P Series user manual

Ltech

Ltech E5S manual

Harman

Harman AMX MODERO S MSD-701-L2 quick start guide

Acnodes

Acnodes PC 1150 installation guide

AIS

AIS IP10IA99 series user guide

IBASE Technology

IBASE Technology ASTUT-152-RE1S user manual

YASKAWA

YASKAWA TP 610C manual

B&R

B&R Power Panel C Series user manual

Beijer Electronics

Beijer Electronics X2 control Hardware and installation manual

AXIOMTEK

AXIOMTEK GOT321W-521 user manual

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Operation manual

Qomo

Qomo QIT1386 user manual

DFI

DFI KS104-CD user manual

AMX

AMX AXP-PPC Dimensional drawing

Sartorius

Sartorius X3 PR 5410 operating manual

AMX

AMX Modero X Series quick start guide

Advantech

Advantech TPC-30 Series user manual