ZDC ZA-5000-D User manual
ZDC Dual-RF Outdoor Wireless Access Point
ZA-5000-D
Quick Installation Guide
== CONFIDENTIAL (All right reserved by ZDC) ==
1
== CONFIDENTIAL (All right reserved by ZDC) ==
2
Table of Contents
¾ZA-5000-D Introduction
¾Appearance of Product
¾Hardware Installation
¾Configuration PC
¾Quick Build Wireless Outdoor Bridge
¾Technical support
== CONFIDENTIAL (All right reserved by ZDC) ==
3
1. ZA-5000-D Introduction
The next-generation Broadband Wireless Access deviceˉZA-5000-D Dual-RF Outdoor Wireless Access Point,
Simultaneously works as 5GHz Bridge and 2.4GHz Access Point. The new features and benefits are:
support POE (power over Ethernet); support testlink, use this utility, you can place the antenna in the best place.
Surface packing is full block out and with waterproof function. The Access Point provides powerful features.
Appearance of Product
Hardware Installation
Package Content
Before installation, make sure that you the following items:
ZA-5000-D*1
DC Injector*1
Product CD*1
Power Adapter*1
Fixed settings*1
Installation
Take the following steps to setup the Dual-RF Outdoor Wireless Access Point.
Hardware equipment
Fixation
First you should fix the Access Point, the following figure show it:
== CONFIDENTIAL (All right reserved by ZDC) ==
4
Connect the Ethernet
The Access Point supports 10/100M Ethernet connection. Attach UTP Ethernet cable to the RJ-45
connector on the Access Point. Then connect the other end of the RJ-45 cable to a hub or a station.
Put UTP cable through the water-joint
Make the RJ-45 connector:
white orangeorange white greenblue white bluegreen white brownbrown
Plug water-joint into the Access Point and close the water-joint.
Notice˖For protected build-in 23dBi gain antenna of wireless1, Surface of device
was placed plastic protective pellicle, when you use device, please rip away.
== CONFIDENTIAL (All right reserved by ZDC) ==
5
Notice˖Wireless2 of device need additional high gain antenna, you may select
appropriate antenna by real situation, and suggest that there has long distance
between antenna of wireless1 and antenna of wireless2 for preventing interference.
Warning˖Please confirm ground connection of the Access Point.
Configuration PC
This section introduces you how to configuration TCP/IP protocol into your personal computer.
And suppose you have been successfully installed one network card on your personal computer.
Windows 98/Me
1. Click the Start button, select Settings, then select Control Panel
2. Double-click the Network Icon
3. In the configuration tab, select the TCP/IP protocol line that is associated with your network
card/adapter. If there is no TCP/IP line listed, you will need to first install the TCP/IP
protocol.
4. Click the Properties button, then choose the IP Address tab. Select Specify an IP address.
5. Enter an IP address in the IP field, within the range of 192.168.0.X(X can’t be 228).
6. After clicking OK, windows might ask you to restart the PC. Click Yes.
Windows 2000/XP
1. Click start button, select Settings, then click control panel.
2. Right-click the network icon and select open to open the network connections dialog.
3. Right-click the appropriate LAN connection and click properties to open the properties
dialog for the connection:
4. Check the box next to Internet Protocol (TCP/IP) and click properties.
5. In the TCP/IP Properties dialog box, click the radio button next to use the following IP
address.
6. Enter an IP address in the IP field, within the range of 192.168.0.X(X can’t be 228).
== CONFIDENTIAL (All right reserved by ZDC) ==
6
2. Quick Build Outdoor Wireless Bridge
Step.
1. The hardware is installed.
2. Run Web Explorer, Enter default IP Address (192.168.0.228) of the Access Point in the
Address field. Enter default User Name (admin) and default Password (password), Click
“Login” button. The main page will show up.
== CONFIDENTIAL (All right reserved by ZDC) ==
7
Notice: Please use more than Microsoft IE 6. 0 browsers!
3. Configuration IP Address of the Access Point.
Notice: IP address must be in the same net section and not the same!
== CONFIDENTIAL (All right reserved by ZDC) ==
8
4. Configuration Wireless1 the parameter of the Access Point, including: Country/Region,
Channel, Data Rate and Remote MAC Address.
5. Configuration Wireless2 the parameters of the Access Point. including: AP Mode, SSID (in AP
Mode), Country/Region, Wireless Mode, Channel, Data Rate, and type MAC Address of the
remote wireless device (in Bridge Mode).
== CONFIDENTIAL (All right reserved by ZDC) ==
9
Warning: In the Bridge mode, Country/Region, Channel, Data Rate of devices must to
be same, otherwise unable to setup wireless chain.
Note: If you experience interference (shown by lost connections and/or slow data
transfers) you may need to experiment with different channels to see which is the best
and wireless1 and wireless2 had better not set the same channel.
6. Use Link test function and test wireless chain.
Select MAC Address of wireless1 in Local MAC list, then input the parameters of Space
Between AP, RF Cable Loss, Local Antenna Gain and Remote Antenna Gain, click “Apply”
button, then click “Start” button, test wireless1 chain.
Select MAC Address of wireless2 in Local MAC list, then select Remote MAC Address in
Remote MAC list, input the parameters of Space Between AP, RF Cable Loss, Local Antenna
Gain and Remote Antenna Gain, click “Apply” button, then click “Start” button, test wireless2
chain.
Notice: In Bridge Mode, the value of Space Between AP should close to the real
distance.
Warning: The value of Space Between AP must be input.
View the intensity of signal, and adjust the positions and angles of the antenna according to the
== CONFIDENTIAL (All right reserved by ZDC) ==
10
intensity of signal. Adjust the antenna from side to side from head to foot, observe the number
value of dBm at the same time. When the number value of dBm is the greatest, the antenna is in
the best positions.
Notice: Two kinds of expression methods that equipment has offered the intensity of
signal to compare with intensity of signal, the intensity of signal than only generally
consults the meaning, is subject to number value of the intensity of signal (dBm) while
adjusting the antenna!
If wireless2 work In Point-to-Multipoint mode, then must test every chain.
Notice: In the Point-to-Multipoint mode, central point input the distance from the
central point to the farthest remote point, Each remote point input the real distance from
the each remote point to the central point.
Technical support
You can access the Web page: http://www.zcom.com.cn/chinese/download.asp?styleid=1.
Upgrade latest version software to download, if meet difficulty and please contact our supplier in
the course of installing and using the Access Point.
Nanjing Z-com Wireless Co.,Ltd
Addr˖168 Longpan Zhong Road JiangSu Software
Park Suite#118
Postcode˖210002
Tele˖025-84661320
Fax˖025-84661313
Websites˖www.zcom.com.cn
E-Mail˖[email protected].cn
Table of contents
Other ZDC Wireless Access Point manuals
