Yunlink CPE150-P24 User manual
1
User Manual
This is the user manual of Outdoor WiFi Bridge with Qualcomm Chipset, which will approximate guide you how to set
and apply this product. It provide a convenient graphical interface for network construction and maintenance person,
as well as a user through a simple and accurate operation, and configuration management of the ceiling wireless
access point.
Test Model：CPE150-P24
2
Attention:
1. Check box contents:
Outdoor CPE
PoE Power adapter (for 24V Passive PoE device)
LAN cable
User Manual
Installation Accessory
2. Warning:
Do not use the same power source for the product as other equipment, Only use the power adapter that comes
with the package. Using a different voltage rating power adapter may damage the device.
Do not open or repair the case yourself. If the product is too hot, turn off the power immediately and have it
repaired at a qualified service center.
3
Contents
Chapter 1: Hardware and Operation mode Instruction……………........…………...………….......……….4
1.1 Interface Instruction..……………........……………………..........................................………4
1.2: LED light instruction…………........…………………….........................................................4
1.3 PoE Power Connection and Installation……………….........................................................4
Chapter 2: Working Diagram………………..............................................................................................5
Chapter 3: WDS Switch Button Configuration………………....................................................................5
Chapter 4: WEB GUI Login………………................................................................................................9
Chapter 5 : WEB GUI interface Setting……...........................................................................................11
5. 1 User Login Page……........................................................................................................11
5.1.1 Wireless Setting…..........................................................................................................11
5.1.2 LAN Setting….................................................................................................................12
5.1.3 Super WDS Settings .....................................................................................................12
5.1.4 Wizard............................................................................................................................14
5.1.5 Advanced........................................................................................................................14
5.2 Admin Login.......................................................................................................................14
5.2.1: Wizard............................................................................................................................15
5.2.1.1 Gateway Mode.............................................................................................................16
5.2.1.2 WiFi Repeater mode…………………………………………………………….....….........18
5.2.1.3. WISP Operation mode:…………………………………………………….....……...........19
5.2.1.4. AP Operation mode:……………………………………………………………....…..........21
5.2.1.5 Super WDS Mode.........................................................................................................23
5.3 Advanced Setting…………………………………………………….…………...………...........23
5.3.1 Device Status:……………………………………………………………………...……..........23
5.3.2Wireless…………………………………………………………....………..............................24
5.3.4 Network setting……………………………………………………………………….......……27
5.3.5 Management……………………………………………………………………………..........28
Chapter 6 Share Internet and Obtain IP address automatically……………………………....….…….....31
Chapter 7 Trouble Shooting…………………………………………………………………………………...32
4
Chapter 1: Hardware and Operation mode Instruction
1.1 Interface Instruction:
P1 Product Interface
LAN: 1*10/100Mbps RJ45 port, can support 24V Passive PoE.
WAN: 1*10/100Mbps RJ45 port, can support 24V Passive PoE, but it change to LAN port under WDS, WiFi Repeater
operation mode
RST: Reset Button, press 10~15 seconds, outdoor CPE will revert to default settings.
DC: 12V/1A DC input injector.
WDS Switch Button: S: mean slaver AP; M: mean master AP.
1.2: LED light instruction:
LED Light Name Status Instruction
SYS System Light
Blue color, Slow Blinking Master AP
Blue color, Light Slave AP
Blue color, Fast Blinking Reset to Default
WAN WAN Port Green Color, Light Connected
LAN LAN Port Green Color, Light Connected
WiFi Status LED Light Green Color, Blinking WiFi transmission OK
Signal Strength Green Color, Blinking in
proper order Working as normal
5
1.3 PoE Power Connection and Installation
There is a PoE adapter and Installation Accessory in the box, then pls install and power the outdoor CPE as following
pictures:
P2 Power Connection and Installation
Chapter 2: Working Diagram
Then outdoor CPE with panel antenna, mostly for Point to Point and Point to multi Point connections.
Take outdoor CPE work with IP camera for example to show the working diagram:
A. PTP Working Diagram of Outdoor CPE work in Elevator:
P3: Working diagram
6
B. PTP Working Diagram of Outdoor CPE work with Multiple IP Camera:
P4: Working diagram
C. PTMP Working Diagram of Outdoor CPE work with IP Camera:
P5: Working diagram
D. PTMP Working Diagram of Outdoor CPE work with Multiple IP Camera:
P6: Working diagram
7
E. PTP Working Diagram of Outdoor CPE applied to Wireless Coverage:
P7: Working diagram
Chapter 3: WDS Switch Button Configuration
This Outdoor CPE support Wireless AP, Gateway, WISP, Wireless Bridge, WDS operation mode, effective solution for
PTP, PTMP application and outdoor long range wifi coverage application. What’s more, there is WDS button on the
case, easy to do PTP,PTMP connection by press the WDS button and reset button, no need to access into product
GUI.
P9: WDS Switch Button
Here we are show how to the connection by press the WDS switch button:
S: Mean Slave AP
M: Mean Master AP
When WDS switch button on M side, mean this outdoor CPE is a master AP;
When WDS switch button on S side, mean this outdoor CPE is an slave AP
8
Remark:
The master AP can connect with 1~4 slave AP
The WDS switch button in S side in default
The default IP address of master AP and slave AP is 192.168.288.253.
Operation:
1st : Power on the Master AP and Slave AP;
2nd: Push the WDS switch button to M side on Master AP, Master AP’s IP address will change to 192.168.188.252.
3rd: Press the reset button on master AP and Slave AP together in 1 second, then 4 signal LED light will flash together
like following picture:
P10: LED Light Status
4th: Wait a while, the slave AP will connect with master AP automatically, then master AP and slave AP LED signal LED
lights flash one by one as following picture:
9
P11: LED Light Status
If there are 2~4 Slave APs, the 4 steps will change to as follow:
Press the reset button around 1 second on the 2nd slave AP, 3rd slave AP, 4th slave AP, and finish this step in 2 mins,
then all slave AP will connect with master AP automatically; The LED lights status is same.
Chapter 4: WEB GUI Login
1）Connect the Outdoor CPE with computer by wired or wireless
2）The default IP address of this outdoor CPE is 192.168.188.253, Configure the PC’s local connection IP address as
192.168.188.X (X is number from 2 to 254), subnet mask is 255.255.255.0, follow P4 and P5 to finish.
10
P12 Setting of computer’s IP address
P13 Setting of computer’s IP address
Input 192.168.188.253 into IE browser, then pop up the login page, there are user/admin login page, input admin to
login the user page; or input root to login the admin page.
Table of contents
Other Yunlink Wireless Access Point manuals
