York GHGD18 Quick start guide

SPLIT-SYSTEM HEAT PUMPS

13 SEER – R-410A – Single Phase

MODELS:

GHGD18 THRU 60

(1.5 THRU 5 NOMINAL TONS)

Due to continuous product improvement, specifications

are subject to change without notice.

Visit us on the web at www.york.com

Additional rating information can be found at

www.ahridirectory.org

WARRANTY

5-year limited parts warranty.

5-year limited compressor warranty.

LISTED

TECHNICAL

GUIDE

TECHNICAL

GUIDE

571921-UTG-A-0410

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

DESCRIPTION

The 13 SEER Series unit is the outdoor part of a versatile cli-

mate system. It is designed with a matching indoor coil compo-

nent from Johnson Controls Unitary Products. Available for

typical applications this climate system is supported with acces-

sories and documents to serve specific functions.

FEATURES

•Quality Condenser Coils - The coil is constructed of copper

tubing and enhanced aluminum fins for increased efficiency

and corrosion protection.

•Protected Compressor - The compressor is internally pro-

tected against high pressure, temperature, and externally by

a factory installed high pressure switch. This is accomplished

by the simultaneous operation of high pressure relief valve

and a temperature sensor which protects the compressor if

undesirable operating conditions occur. A liquid line filter-

drier further protects the compressor.

•Durable Finish - The cabinet is made of pre-painted steel.

The pre-treated galvanized steel provides a better paint to

steel bond, which resists corrosion and rust creep. Special

primer formulas and matted-textured finish insure less fading

when exposed to sunlight.

•Lower Installed Cost - Installation time and costs are

reduced by easy power and control wiring connections.

Available in sweat connect models only. The unit contains

enough refrigerant for matching indoor coils and 15 feet of

interconnecting piping. The small base dimension means

less space is required on the ground or roof.

•Top Discharge - The warm air from the top mounted fan is

blown up away from the structure and any landscaping. This

allows compact location on multi-unit applications.

•Low Operating Sound Level - The upward air flow carries

the normal operating noise away from the living area. The

rigid top panel effectively isolates any motor sound. Isolator

mounted compressor and the rippled fins of the condenser

coil muffle the normal fan motor and compressor operating

sounds.

•Low Maintenance - Long life permanently lubricated motor-

bearings need no annual servicing.

•Easy Service Access - Fully exposed refrigerant connec-

tions, and a single panel covering the electrical controls

make for easy servicing of the unit.

•Secured Service Valves - Secured re-usable service valves

are provided on both the liquid and vapor sweat connections

for ease of evacuating and charging.

•U.L. and C.U.L. listed - approved for outdoor application.

•Agency Listed -U.L. and C.U.L. listed - approved for out-

door application. The unit is certified in accordance with the

Unitary Small Equipment certification program, which is

based on ARI Standard 210/240.

571921-UTG-A-0410

2Johnson Controls Unitary Products

All dimensions are in inches. They are subject to change with-

out notice. Certified dimensions will be provided upon request.

Physical and Electrical Data

MODEL GHGD18

S41S3 GHGD24

S41S4 GHGD30

S41S4 GHGD36

S41S4 GHGD42

S41S4 GHGD48

S41S4 GHGD60

S41S4

Unit Supply Voltage 208-230V, 1 60Hz

Normal Voltage Range 1187 to 252

Minimum Circuit Ampacity 11.9 11.2 14.1 19.7 20.9 25.6 34.9

Max. Overcurrent Device Amps 220 15 20 30 35 45 60

Min. Overcurrent Device Amps 315 15 15 20 25 30 35

Compressor Type Scroll Recip Recip Recip Recip Recip Scroll

Compressor Amps Rated Load 9.0 8.3 10.6 14.7 15.7 19.4 26.9

Locked Rotor 48.0 43.0 54.0 74.0 88.0 88.0 135.0

Crankcase Heater No Yes Yes Yes Yes Yes No

Fan Motor Amps Rated Load 0.70 0.80 0.80 1.3 1.3 1.3 1.3

Fan Diameter Inches 24 24 24 24 24 24 24

Fan Motor Rated HP 1/10 1/8 1/8 1/4 1/4 1/4 1/4

Nominal RPM 825 1075 1075 850 850 850 850

Nominal CFM 2000 2900 3000 3800 3800 3600 3600

Coil Face Area Sq. Ft. 15.7 18.3 21.0 23.6 23.6 23.6 23.6

Rows Deep 1 1 1 1 1 2 2

Fin / Inches 22 22 22 22 22 18 18

Liquid Line Set OD (Field Installed) 3/8 3/8 3/8 3/8 3/8 3/8 3/8

Vapor Line Set OD (Field Installed) 3/4 3/4 3/4 3/4 7/8 7/8 7/8

Unit Charge (Lbs. - Oz.) 46 - 6 9 - 6 9 - 0 10 - 0 9 - 10 14 - 12 13 - 13

Charge Per Foot, Oz. 0.62 0.62 0.62 0.62 0.67 0.67 0.67

Operating Weight Lbs. 172 194 206 218 218 285 284

1. Rated in accordance with ARI Standard 110, utilization range “A”.

2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection.

3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection.

4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add

or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value.

Unit

Model

Dimensions

(Inches) Refrigerant Connection

Service Valve Size

1. Including Fan Guard.

B C Liquid Vapor

18 28 34 34

3/8”

3/4”

24 32 34 34

30 36 34 34

36 40 34 34

42 40 34 34 7/8”48 40 34 34

60 40 34 34

571921-UTG-A-0410

Johnson Controls Unitary Products 3

PROCEDURES:

1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting

line tubing.

2. Verify the TXV and additional charge required for specific evaporator coil in the system using the above table.

3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in Physical and Electrical Data Table.

4. For TXV matches requiring additional charge, the refrigerant needs to be weighed in for specific coil match and lineset length.

5. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator +

adder for line set.

System Charge for Various Matched Systems

Outdoor Unit GHGD18S41S3 GHGD24S41S4 GHGD30S41S4 GHGD36S41S4 GHGD42S41S4 GHGD48S41S4 GHGD60S41S4

Required Orifice or TXV 1

1. For applications requiring a TXV use 1TVM0 series kit.

.051/4F1 .054/4G1 .063/4G1 .071/4H1 .075/4H1 4J1 4K1

Factory Charge, lbs-oz 6 - 6 9 - 6 9 - 0 10 - 0 9 - 10 14 - 12 13 - 13

Indoor Coil2,3

2. Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224.

3. PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications.

Additional Charge, Oz

FC/MC/PC/UC18 .051/ TXV + 0 ––––––

FC/MC/PC/UC24 .051/ TXV + 5 ––––––

FC/MC/PC/UC30 .051/ TXV + 5 ––––––

FC/MC/PC32 –.054/TXV+0.063/TXV+0––––

FC/MC/PC35 –.054/TXV+0.063/TXV+0––––

FC/MC/PC37 – .054 / TXV + 5 .063 / TXV + 6 .071 / TXV + 0 – – –

FC/MC/PC43 – .054 / TXV + 5 .063 / TXV + 6 .071 / TXV + 0 – – –

FC/MC/PC/UC48 – – – .071 / TXV + 10 .075 / TXV + 0 – –

FC/MC/PC/UC60 ––––.075/TXV+8TXV+0–

FC/PC62 –––––TXV+5TXV+0

FC64 ––––––TXV+8

HD18 .051/ TXV + 14 ––––––

HD24 .051/ TXV + 0 ––––––

HD48 – – – .071 / TXV + 13 – – –

HD60 ––––.075/TXV+10––

AHP18 .051/ TXV + 0 ––––––

AHP24 .051/ TXV + 2 ––––––

AHP30 –.054/TXV+0.063/TXV+0––––

AHP36 – – .063 / TXV + 6 .071 / TXV + 0 – – –

AHP42 – – – .071 / TXV + 0 – – –

AHP48 ––––.075/TXV+8TXV+0–

AHP60 ––––.075/TXV+8TXV+0–

AHX18 .051/ TXV + 0 ––––––

AHX30 –.054/TXV+0.063/TXV+0––––

AHX36 – .054 / TXV + 5 .063 / TXV + 6 .071 / TXV + 0 – – –

AHX42 – – – .071 / TXV + 10 .075 / TXV + 0 – –

AHX48 ––––.075/TXV+8TXV+0–

AHX60 –––––TXV+5TXV+0

AV24 .051/ TXV + 2 ––––––

AV36 – .054 / TXV + 5 .063 / TXV + 6 .071 / TXV + 0 – – –

AV48 ––––.075/TXV+8TXV+0–

AV60 ––––.075/TXV+8TXV+0–

F4FP024 .051/ TXV + 0 ––––––

F4FP040 –.054/TXV+0.063/TXV+0––––

F4FP045 – .071 / TXV + 14 .075 / TXV + 8 – –

F4FV060 – .075 / TXV + 8 TXV + 0 –

F5FP048 – .071 / TXV + 12 .075 / TXV + 0 – –

F5FP060 – – .075 / TXV + 8 TXV + 0 –

F6FP018 .051/ TXV + 0 ––––

F6FP024 .051/ TXV + 2 ––––

F6FP030 –.054/TXV+0.063/TXV+0––––

F6FP036 –.054/TXV+0.063/TXV+0––––

F6FP042 – – – .071 / TXV + 10 .075 / TXV + 0 – –

F6FP048 ––––.075/TXV+8TXV+0–

F6FP060 –––––TXV+5TXV+0

FOOTNOTES:

571921-UTG-A-0410

4Johnson Controls Unitary Products

COOLING CAPACITY - With Air Handler Coils

UNIT

MODEL

AIR HANDLER COIL

MODEL1

COOLING

MODEL W RATED

CFM NET MBH SEER EER

TOTAL SENS.

13 SEER HP WITH MA

GHGD18S41S3 MA08B 17 FC/MC18B 600 18.0 14.0 13.00 11.00

MA08B 17 FC/MC24B 600 18.0 14.0 13.50 11.00

GHGD24S41S4 MA12B 17 FC/MC35 800 23.6 17.1 13.00 11.00

MA12B 17 FC/MC43 800 24.0 17.3 13.00 11.00

GHGD30S41S4 MA12B 17 FC/MC35 1000 29.8 21.8 13.00 11.00

MA12B 17 FC/MC43 1000 30.0 22.2 13.00 11.00

GHGD36S41S4 MA12B 17 FC/MC43 1200 36.0 26.6 13.00 11.00

GHGD42S41S4 MA16C 21 FC/MC60 1400 41.0 31.8 13.00 11.00

GHGD48S41S4 MA16C 24 FC/MC60 1600 44.0 33.4 13.00 11.00

GHGD60S41S4 MA20D 24 FC/MC62 1800 55.0 40.0 13.00 11.00

MA20D 24 FC64 1800 56.0 41.5 13.00 11.00

13 SEER HP WITH MV - VARIABLE SPEED

GHGD18S41S3 MV12B 17 FC/MC18B 600 18.0 13.7 14.00 12.00

MV12B 17 FC/MC24B 600 18.0 13.7 14.00 12.00

GHGD24S41S4 MV12B 17 FC/MC35B 800 24.0 17.5 14.50 12.00

MV12B 17 FC/MC43B 800 24.0 17.3 14.50 12.00

GHGD30S41S4

MV12B 17 FC/MC35B 1010 30.0 22.0 14.50 12.00

MV16C 21 FC/MC35C 1070 30.0 23.0 14.50 12.00

MV12B 17 FC/MC43B 1000 30.0 22.2 14.50 12.00

MV16C 21 FC/MC43C 1000 30.0 22.2 14.50 12.00

GHGD36S41S4

MV12B 17 FC/MC43B 1225 36.0 27.2 14.50 12.00

MV16C 21 FC/MC43C 1200 36.0 26.8 14.50 12.00

MV12D 24 FC/MC48D 1160 36.0 26.6 14.50 12.00

MV16C 21 FC/MC48C 1200 36.0 26.6 14.50 12.00

GHGD42S41S4

MV16C 21 FC/MC48C 1400 40.0 32.0 13.50 11.50

MV20D 24 FC/MC48D 1440 40.5 32.8 14.00 12.00

MV16C 21 FC/MC60C 1400 41.5 32.4 14.00 12.00

MV20D 24 FC/MC60D 1400 42.0 32.4 14.00 12.00

GHGD48S41S4 MV16C 21 FC/PC60C 1600 44.0 33.4 14.00 11.50

MV20D 24 FC/MC60D 1600 44.5 33.8 14.50 12.00

MV20D 24 FC/MC62D 1630 45.5 34.4 14.50 12.00

GHGD60S41S4 MV20D 24 FC/MC62D 1855 55.5 40.5 13.75 11.50

MV20D 24 FC64D 1855 56.0 41.5 14.00 12.00

13 SEER HP WITH AV / SV / F*FV - VARIABLE SPEED

GHGD18S41S3 AV*24 17 – 550 18.0 13.7 14.00 12.00

GHGD24S41S4 AV*36 21 – 725 24.0 17.0 14.50 12.00

GHGD30S41S4 AV*36 21 – 960 30.0 22.4 14.50 12.00

GHGD36S41S4 AV*36 21 – 1190 36.0 26.8 14.50 12.00

GHGD42S41S4 F4FV060 24 – 1350 40.5 32.2 14.00 12.00

AV*48 24 – 1385 42.0 32.6 14.50 12.00

AV*60 24 – 1360 42.0 32.6 14.50 12.00

GHGD48S41S4 F4FV060 24 – 1665 44.5 34.2 14.50 12.00

AV*48 24 – 1625 45.0 34.4 14.50 12.00

AV*60 24 – 1560 45.0 34.6 14.50 12.00

For Notes See Page 5.

571921-UTG-A-0410

Johnson Controls Unitary Products 5

— = Not applicable.

13 SEER HP WITH AHP / SHP / AHX / F*FP

GHGD18S41S3

AHP18 17 – 600 18.0 14.0 13.00 11.00

AHX18 17 – 600 18.0 14.0 14.50 12.00

F4FP024 17 – 600 18.0 14.0 13.00 11.00

F6FP018 17 – 600 18.0 14.0 14.50 12.00

F6FP024 17 – 610 18.0 14.0 14.50 12.00

GHGD24S41S4

AHP30 17 – 800 23.8 17.1 13.00 11.00

F4FP040 21 – 800 23.8 17.1 13.00 11.00

AHX30 17 – 820 24.0 17.5 14.00 12.00

AHX36 21 – 820 24.0 17.5 14.00 12.00

F6FP030 17 – 850 24.0 17.6 14.00 12.00

F6FP036 21 – 855 24.0 17.6 14.00 12.00

GHGD30S41S4

AHP30 17 – 1000 30.0 22.2 13.00 11.00

AHP36 21 – 1000 30.0 22.2 13.00 11.00

AHX30 17 – 1025 30.0 22.6 14.50 12.00

AHX36 21 – 1005 30.0 22.4 14.50 12.00

F4FP040 21 – 1000 29.8 21.8 13.00 11.00

F6FP030 17 – 1035 30.0 22.0 14.00 11.50

F6FP036 21 – 980 30.0 22.0 14.50 12.00

GHGD36S41S4

AHP36 21 – 1200 36.0 26.4 13.00 11.00

AHX36 21 – 1225 36.0 26.8 14.50 12.00

F6FP042 24 – 1290 36.0 27.6 14.50 12.00

F5FP048 24 – 1235 36.0 27.2 14.50 12.00

F4FP045 24 – 1200 36.0 26.8 13.00 11.00

AHX42 21 – 1190 36.0 26.8 14.50 12.00

AHP42 21 – 1255 36.0 27.2 13.00 11.00

GHGD42S41S4

AHX42 21 – 1395 40.5 32.4 14.00 12.00

F6FP042 24 – 1455 40.5 32.8 13.50 11.50

AHP60 24 – 1400 42.0 32.4 14.00 12.00

AHP48 24 – 1370 41.0 31.0 13.00 11.00

AHX48 24 – 1445 42.0 33.0 14.50 12.00

F4FP045 24 – 1400 41.0 31.8 13.00 11.00

F5FP048 24 – 1455 41.5 32.6 14.00 12.00

F6FP048 24 – 1380 42.0 32.4 14.50 12.00

F5FP060 24 – 1485 42.0 33.2 14.00 12.00

GHGD48S41S4

AHP48 24 – 1685 45.0 34.6 13.00 11.00

AHP60 24 – 1600 44.5 34.0 14.50 12.00

AHX48 24 – 1660 45.5 35.0 14.50 12.00

AHX60 24 – 1570 45.5 34.4 14.50 12.00

F5FP060 24 – 1665 44.5 34.2 14.50 12.00

F6FP048 24 – 1625 45.0 34.4 14.50 12.00

F6FP060 24 – 1570 45.5 34.4 14.50 12.00

GHGD60S41S4 AHX60 24 – 1830 55.0 40.5 14.00 11.50

F6FP060 24 – 1875 56.0 41.5 14.00 12.00

Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210.

Cooling MBH based on 8°F entering air temperature, 50% RH, and rated air flow.

EER (Energy Efficiency Ratio) is the total cooling output in BTU’s at 95°F outdoor ambient divided by the total electric power in watt-hours at those conditions.

SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU’s during a normal annual usage period for cooling divided by the total electric power

input in watt-hours during the same period.

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.

COOLING CAPACITY - With Air Handler Coils (Continued)

UNIT

MODEL

AIR HANDLER COIL

MODEL1

COOLING

MODEL W RATED

CFM NET MBH SEER EER

TOTAL SENS.

571921-UTG-A-0410

6Johnson Controls Unitary Products

COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils

UNIT MODEL

FURNACE** COIL

MODEL

COOLING

CFM RANGE

(Min.-max.) WRATED

CFM NET MBH SEER1EER

TOTAL SENS.

GHGD18S41S3

450 - 750 14,17 FC/MC/PC18 600 18.0 14.0 13.00 11.00

450 - 750 14,17 FC/MC/PC24 600 18.0 14.0 13.50 11.00

450 - 750 14 HC18 600 18.0 14.0 13.00 11.00

450 - 750 14 HD24 600 18.0 14.0 13.50 11.00

GHGD24S41S4

600 - 1000 14 FC/MC/PC32 800 23.8 17.1 13.00 11.00

600 - 1000 17,21 FC/MC/PC35 800 23.6 17.1 13.00 11.00

600 - 1000 14 FC/MC/PC37 800 24.0 17.3 13.00 11.00

600 - 1000 17,21 FC/MC/PC43 800 24.0 17.3 13.00 11.00

GHGD30S41S4

800 - 1200 14 FC/MC/PC32 1000 29.8 21.8 13.00 11.00

800 - 1200 17,21 FC/MC/PC35 1000 29.8 21.8 13.00 11.00

800 - 1200 14 FC/MC/PC37 1000 30.0 22.2 13.00 11.00

800 - 1200 17,21 FC/MC/PC43 1000 30.0 22.2 13.00 11.00

GHGD36S41S4

1000 - 1400 17,21 FC/MC/PC43 1200 36.0 26.6 13.00 11.00

1000 - 1400 14 FC/MC/PC37 1200 36.0 26.8 13.00 11.00

1000 - 1400 – HD48 1200 36.0 26.4 13.00 11.00

1000 - 1400 21,24 FC/MC/PC48 1200 36.0 26.6 13.00 11.00

1000 - 1400 21,24 UC48 1200 36.0 26.8 13.00 11.00

GHGD42S41S4 1200 - 1600 21,24 FC/MC/PC60 1400 41.0 31.8 13.00 11.00

1200 - 1600 – HD60 1400 41.0 31.4 13.00 11.00

1200 - 1600 21,24 UC60 1400 40.5 31.0 13.00 11.00

GHGD48S41S4 1400 - 1800 21,24 FC/MC/PC60 1600 44.0 33.4 13.00 11.00

1400 - 1800 24 FC/MC62 1600 44.5 33.8 13.00 11.00

1400 - 1800 21,24 UC60 1600 44.0 32.8 13.00 11.00

GHGD60S41S4 1600 - 2000 24 FC/MC62 1800 55.0 40.0 13.00 11.00

1600 - 2000 24 FC64 1800 56.0 41.5 13.00 11.00

1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one.

** Refer to Quick Selection Chart for specific furnace match-up.

571921-UTG-A-0410

Johnson Controls Unitary Products 7

COOLING CAPACITY - With High Efficiency Motor Furnaces

UNIT

MODEL FURNACE

MODEL COIL

MODEL1WCOOLING

RATED

CFM Net MBH SEER EER

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES2

GHGD18S41S3

T*(8,L)X*A12 FC/MC/PC18A 14 540 18.0 14.3 14.00 12.00

T*(8,L)X*B12 FC/MC/PC18B 17 580 18.0 14.6 14.00 12.00

T*9X*B12 FC/MC/PC18B 17 590 18.0 14.7 14.00 12.00

T*(8,L)X*A12 FC/MC/PC24A 14 595 18.0 14.9 14.00 12.00

T*(8,L)X*B12 FC/MC/PC24B 17 620 18.0 14.9 14.00 12.00

T*9X*B12 FC/MC/PC24B 17 615 18.0 14.9 14.00 12.00

T*(8,L)X*A12 FC/MC/PC30A 14 595 18.0 14.9 14.00 12.00

T*(8,L)X*B12 FC/MC/PC30B 17 620 18.0 14.9 14.00 12.00

T*9X*B12 FC/MC/PC30B 17 615 18.0 14.9 14.00 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC18A 14 620 18.0 12.3 14.50 12.30

(T*(8,L)C/T*8V)*B12 FC/MC/PC18B 17 580 18.0 11.9 14.40 12.20

(T*9C/T*9V)*B12 FC/MC/PC18B 17 610 18.0 12.2 14.60 12.40

(T*(8,L)C/T*8V)*A12 FC/MC/PC24A 14 640 18.0 12.7 14.80 12.50

(T*(8,L)C/T*8V)*B12 FC/MC/PC24B 17 575 18.0 12.2 14.90 12.60

(T*9C/T*9V)*B12 FC/MC/PC24B 17 610 18.0 12.7 14.90 12.60

(T*(8,L)C/T*8V)*A12 FC/MC/PC30A 14 640 18.0 12.7 14.80 12.50

(T*(8,L)C/T*8V)*B12 FC/MC/PC30B 17 575 18.0 12.2 14.90 12.60

(T*9C/T*9V)*B12 FC/MC/PC30B 17 610 18.0 12.7 14.90 12.60

(T*(8,L)C/T*8V)*A12 HC18 14 620 18.0 12.3 14.50 12.30

(T*(8,L)C/T*8V)*A12 HD24 14 640 18.0 12.6 14.90 12.60

(T*(8,L)C/T*8V)*B12 HD24 17 575 18.0 12.2 14.90 12.60

(T*9C/T*9V)*B12 HD24 17 610 18.0 12.6 15.00 12.70

(T*(8,L)C/T*8V)*A12 UC18A 14 620 18.0 12.4 14.60 12.30

(T*(8,L)C/T*8V)*B12 UC18B 17 580 18.0 12.0 14.60 12.30

(T*9C/T*9V)*B12 UC18B 17 610 18.0 12.3 14.80 12.40

(T*(8,L)C/T*8V)*A12 UC24A 14 640 18.0 12.8 14.80 12.50

(T*(8,L)C/T*8V)*B12 UC24B 17 575 18.0 12.3 14.90 12.60

(T*9C/T*9V)*B12 UC24B 17 610 18.0 12.8 14.90 12.60

(T*(8,L)C/T*8V)*A12 UC30A 14 640 18.0 12.8 14.80 12.50

(T*(8,L)C/T*8V)*B12 UC30B 17 575 18.0 12.3 15.00 12.60

(T*9C/T*9V)*B12 UC30B 17 610 18.0 12.8 15.00 12.60

GHGD24S41S4

T*(8,L)X*A12 FC/MC/PC32A 14 800 24.0 17.5 14.50 12.00

T*(8,L)X*B12 FC/MC/PC35B 17 850 24.0 17.6 14.50 12.00

T*(8,L)X*C16 FC/MC/PC35C 21 865 24.0 17.6 14.50 12.00

T*(8,L)X*C20 FC/MC/PC35C 21 885 24.0 17.6 14.50 12.00

T*9X*B12 FC/MC/PC35B 17 785 24.0 17.4 14.50 12.00

T*9X*C16 FC/MC/PC35C 21 765 24.0 17.3 14.50 12.00

T*9X*C20 FC/MC/PC35C 21 825 24.0 17.6 14.50 12.00

T*(8,L)X*A12 FC/MC/PC37A 14 840 24.0 17.8 14.50 12.00

T*(8,L)X*B12 FC/MC/PC43B 17 865 24.0 18.0 14.50 12.00

T*(8,L)X*C16 FC/MC/PC43C 21 855 24.0 17.9 14.50 12.00

T*(8,L)X*C20 FC/MC/PC43C 21 815 24.0 17.3 14.50 12.00

T*9X*B12 FC/MC/PC43B 17 800 24.0 17.3 14.50 12.00

T*9X*C16 FC/MC/PC43C 21 785 24.0 17.3 14.50 12.00

T*9X*C20 FC/MC/PC43C 21 790 24.0 17.3 14.50 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 14 775 24.0 17.2 14.00 12.00

(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 17 760 24.0 17.2 14.00 12.00

(T*(8,L)C/T*8V)*C16 FC/MC/PC35C 21 855 24.0 17.6 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC35C 21 740 24.0 17.0 14.50 12.00

(T*9C/T*9V)*B12 FC/MC/PC35B 17 815 24.0 17.6 14.00 12.00

(T*9C/T*9V)*C16 FC/MC/PC35C 21 900 24.0 18.1 14.50 12.00

For Notes See Page 10.

571921-UTG-A-0410

8Johnson Controls Unitary Products

GHGD24S41S4

(T*9C/T*9V)*C20 FC/MC/PC35C 21 755 24.0 17.2 14.50 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 805 24.0 17.3 14.50 12.00

(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 760 24.0 17.2 14.00 12.00

(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 895 24.0 18.1 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 760 24.0 17.2 14.50 12.00

(T*9C/T*9V)*B12 FC/MC/PC43B 17 800 24.0 17.3 14.50 12.00

(T*9C/T*9V)*C16 FC/MC/PC43C 21 810 24.0 17.3 14.50 12.00

(T*9C/T*9V)*C20 FC/MC/PC43C 21 890 24.0 18.1 14.50 12.00

GHGD30S41S4

T*(8,L)X*A12 FC/MC/PC32A 14 970 30.0 22.0 14.00 12.00

T*(8,L)X*B12 FC/MC/PC35B 17 1120 30.0 23.2 14.50 12.00

T*(8,L)X*C16 FC/MC/PC35C 21 1105 30.0 23.2 14.50 12.00

T*(8,L)X*C20 FC/MC/PC35C 21 850 29.8 21.4 14.50 12.00

T*9X*B12 FC/MC/PC35B 17 1085 30.0 23.0 14.50 12.00

T*9X*C16 FC/MC/PC35C 21 1075 30.0 23.0 14.50 12.00

T*9X*C20 FC/MC/PC35C 21 835 29.8 21.2 14.50 12.00

T*(8,L)X*A12 FC/MC/PC37A 14 1105 30.0 23.2 14.50 12.00

T*(8,L)X*B12 FC/MC/PC43B 17 1125 30.0 23.4 14.50 12.00

T*(8,L)X*C16 FC/MC/PC43C 21 955 30.0 22.2 14.50 12.00

T*(8,L)X*C20 FC/MC/PC43C 21 870 30.0 21.6 14.50 12.00

T*9X*B12 FC/MC/PC43B 17 1095 30.0 23.2 14.50 12.00

T*9X*C16 FC/MC/PC43C 21 1055 30.0 22.8 14.50 12.00

T*9X*C20 FC/MC/PC43C 21 720 29.2 19.9 14.50 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC32A 14 1045 30.0 22.0 13.50 11.00

(T*(8,L)C/T*8V)*B12 FC/MC/PC35B 17 995 30.0 22.0 14.50 12.00

(T*(8,L)C/T*8V)*C16 FC/MC/PC35C 21 1025 30.0 22.0 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC35C 21 1080 30.0 23.0 14.50 12.00

(T*9C/T*9V)*B12 FC/MC/PC35B 17 1045 30.0 22.0 14.00 11.50

(T*9C/T*9V)*C16 FC/MC/PC35C 21 1005 30.0 22.0 14.50 12.00

(T*9C/T*9V)*C20 FC/MC/PC35C 21 985 30.0 22.0 14.50 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 950 30.0 22.0 14.50 12.00

(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 1040 30.0 22.8 14.50 12.00

(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 990 30.0 22.2 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 1000 30.0 22.2 14.50 12.00

(T*9C/T*9V)*B12 FC/MC/PC43B 17 1035 30.0 22.2 14.50 12.00

(T*9C/T*9V)*C16 FC/MC/PC43C 21 1030 30.0 22.2 14.50 12.00

(T*9C/T*9V)*C20 FC/MC/PC43C 21 995 30.0 22.2 14.50 12.00

GHGD36S41S4

T*(8,L)X*A12 FC/MC/PC37A 14 1290 36.0 27.6 14.50 12.00

T*(8,L)X*B12 FC/MC/PC43B 17 1300 36.0 27.6 14.50 12.00

T*(8,L)X*C16 FC/MC/PC43C 21 1175 36.0 26.8 14.50 12.00

T*(8,L)X*C20 FC/MC/PC43C 21 1250 36.0 27.4 14.50 12.00

T*9X*B12 FC/MC/PC43B 17 1270 36.0 27.4 14.50 12.00

T*9X*C16 FC/MC/PC43C 21 1260 36.0 27.4 14.50 12.00

T*9X*C20 FC/MC/PC43C 21 1185 36.0 26.8 14.50 12.00

T*(8,L)X*C16 FC/MC/PC48C 21 1185 36.0 26.6 14.50 12.00

T*(8,L)X*C20 FC/MC/PC48C 21 1270 36.0 27.2 14.50 12.00

T*9X*C16 FC/MC/PC48C 21 1280 36.0 27.2 14.50 12.00

T*9X*C20 FC/MC/PC48C 21 1205 36.0 26.6 14.50 12.00

T*9X*D20 FC/MC/PC48D 24 1240 36.0 26.6 14.50 12.00

T*(8,L)X*C16 UC48C 21 1185 36.0 26.8 14.50 12.00

T*(8,L)X*C20 UC48C 21 1270 36.0 27.4 14.50 12.00

T*9X*C16 UC48C 21 1280 36.0 27.4 14.50 12.00

T*9X*C20 UC48C 21 1205 36.0 26.8 14.50 12.00

T*9X*D20 UC48D 24 1240 36.0 26.8 14.50 12.00

For Notes See Page 10.

COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL FURNACE

MODEL COIL

MODEL1WCOOLING

RATED

CFM Net MBH SEER EER

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES2

571921-UTG-A-0410

Johnson Controls Unitary Products 9

GHGD36S41S4

(T*(8,L)C/T*8V)*B12 FC/MC/PC43B 17 1270 36.0 27.2 13.75 11.50

(T*(8,L)C/T*8V)*C16 FC/MC/PC43C 21 1205 36.0 26.8 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC43C 21 1190 36.0 26.8 14.50 12.00

(T*9C/T*9V)*B12 FC/MC/PC43B 17 1200 36.0 26.8 14.00 11.50

(T*9C/T*9V)*C16 FC/MC/PC43C 21 1240 36.0 27.0 14.00 12.00

(T*9C/T*9V)*C20 FC/MC/PC43C 21 1200 36.0 26.8 14.50 12.00

(T*(8,L)C/T*8V)*A12 FC/MC/PC37A 14 1150 36.0 26.4 13.75 11.50

(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 21 1210 36.0 26.6 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 21 1155 36.0 26.6 14.50 12.00

(T*9C/T*9V)*C16 FC/MC/PC48C 21 1195 36.0 26.6 14.50 12.00

(T*9C/T*9V)*C20 FC/MC/PC48C 21 1330 36.0 27.6 14.50 12.00

(T*9C/T*9V)*D20 FC/MC/PC48D 24 1240 36.0 26.6 14.50 12.00

(T*(8,L)C/T*8V)*C16 UC48C 21 1210 36.0 26.8 14.50 12.00

(T*(8,L)C/T*8V)*C20 UC48C 21 1155 36.0 26.8 14.50 12.00

(T*9C/T*9V)*C16 UC48C 21 1195 36.0 26.8 14.50 12.00

(T*9C/T*9V)*C20 UC48C 21 1330 36.0 27.8 14.50 12.00

(T*9C/T*9V)*D20 UC48D 24 1240 36.0 26.8 14.50 12.00

GHGD42S41S4

T*(8,L)X*C16 FC/MC/PC48C 21 1360 40.5 29.4 14.00 12.00

T*(8,L)X*C20 FC/MC/PC48C 21 1475 40.5 30.4 14.00 12.00

T*9X*C16 FC/MC/PC48C 21 1425 40.5 29.8 13.50 11.50

T*9X*C20 FC/MC/PC48C 21 1420 40.5 29.8 13.75 11.50

T*9X*D20 FC/MC/PC48D 24 1435 40.5 30.0 14.00 12.00

T*(8,L)X*C16 FC/PC60C 21 1360 42.0 32.6 14.50 12.00

T*(8,L)X*C20 FC/PC60C 21 1485 42.0 33.4 14.50 12.00

T*9X*C16 FC/PC60C 21 1460 42.0 33.2 14.00 12.00

T*9X*C20 FC/PC60C 21 1460 42.0 33.2 14.50 12.00

T*9X*D20 FC/MC/PC60D 24 1515 42.0 33.6 14.50 12.00

T*(8,L)X*C16 HD60 21 1420 41.5 32.2 14.00 12.00

T*(8,L)X*C20 HD60 21 1410 42.0 32.4 14.00 12.00

T*9X*C16 HD60 21 1465 41.5 32.0 14.00 12.00

T*9X*C20 HD60 21 1465 42.0 32.0 14.00 12.00

T*9X*D20 HD60 24 1460 42.0 32.0 14.00 12.00

T*(8,L)X*C16 UC60C 21 1400 41.5 31.6 14.00 12.00

T*(8,L)X*C20 UC60C 21 1485 41.5 32.8 14.00 12.00

T*9X*C16 UC60C 21 1460 41.0 31.4 13.75 11.50

T*9X*C20 UC60C 21 1460 41.5 31.6 14.00 12.00

T*9X*D20 UC60D 24 1515 42.0 33.2 14.50 12.00

(T*(8,L)C/T*8V)*C16 FC/MC/PC48C 21 1435 40.0 29.8 13.25 11.50

(T*(8,L)C/T*8V)*C20 FC/MC/PC48C 21 1410 40.0 29.6 13.50 11.50

(T*9C/T*9V)*C16 FC/MC/PC48C 21 1395 40.0 29.2 13.20 11.50

(T*9C/T*9V)*C20 FC/MC/PC48C 21 1430 40.0 29.6 13.15 11.50

(T*9C/T*9V)*D20 FC/MC/PC48D 24 1450 40.5 29.8 13.25 11.50

(T*(8,L)C/T*8V)*C16 FC/PC60C 21 1420 41.5 32.2 14.00 12.00

(T*(8,L)C/T*8V)*C20 FC/PC60C 21 1410 42.0 32.4 14.00 12.00

(T*9C/T*9V)*C16 FC/PC60C 21 1445 41.0 32.0 13.25 11.50

(T*9C/T*9V)*C20 FC/PC60C 21 1445 41.5 32.0 13.75 11.50

(T*9C/T*9V)*D20 FC/MC/PC60D 24 1445 41.5 32.2 13.75 11.50

(T*(8,L)C/T*8V)*C16 HD60 21 1420 41.5 31.8 14.00 12.00

(T*(8,L)C/T*8V)*C20 HD60 21 1410 41.5 32.0 14.00 12.00

(T*9C/T*9V)*C16 HD60 21 1445 41.0 31.6 13.25 11.50

(T*9C/T*9V)*C20 HD60 21 1445 41.5 31.8 13.50 11.50

(T*9C/T*9V)*D20 HD60 24 1445 41.5 31.8 13.75 11.50

For Notes See Page 10.

COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL FURNACE

MODEL COIL

MODEL1WCOOLING

RATED

CFM Net MBH SEER EER

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES2

571921-UTG-A-0410

10 Johnson Controls Unitary Products

GHGD42S41S4

(T*(8,L)C/T*8V)*C16 UC60C 21 1420 41.0 31.4 13.75 11.50

(T*(8,L)C/T*8V)*C20 UC60C 21 1410 41.0 31.4 14.00 12.00

(T*9C/T*9V)*C16 UC60C 21 1445 40.5 31.0 13.20 11.50

(T*9C/T*9V)*C20 UC60C 21 1445 41.0 31.2 13.50 11.50

(T*9C/T*9V)*D20 UC60D 24 1445 41.0 31.4 13.50 11.50

GHGD48S41S4

T*(8,L)X*C16 FC/PC60C 21 1605 44.5 33.8 14.50 12.00

T*(8,L)X*C20 FC/PC60C 21 1595 44.5 34.0 14.50 12.00

T*9X*C16 FC/PC60C 21 1575 44.5 33.8 14.50 12.00

T*9X*C20 FC/PC60C 21 1625 44.5 34.0 14.50 12.00

T*9X*D20 FC/MC/PC60D 24 1490 45.5 33.6 14.50 12.00

T*(8,L)X*C16 FC/MC62D 21 1610 45.0 34.2 14.50 12.00

T*(8,L)X*C20 FC/MC62D 21 1665 45.5 34.4 14.50 12.00

T*9X*C16 FC/MC62D 21 1550 45.0 34.2 14.50 12.00

T*9X*C20 FC/MC62D 21 1595 45.0 34.2 14.50 12.00

T*9X*D20 FC/MC62D 24 1610 45.0 34.2 14.50 12.00

T*(8,L)X*C16 UC60C 21 1605 44.5 33.2 14.50 12.00

T*(8,L)X*C20 UC60C 21 1540 45.0 33.6 14.50 12.00

T*9X*C16 UC60C 21 1575 44.5 33.2 14.50 12.00

T*9X*C20 UC60C 21 1625 44.5 33.2 14.50 12.00

T*9X*D20 UC60D 24 1490 44.5 32.8 14.50 12.00

(T*(8,L)C/T*8V)*C16 FC/PC60C 21 1600 44.5 33.6 14.00 12.00

(T*(8,L)C/T*8V)*C20 FC/PC60C 21 1620 44.5 33.8 14.00 12.00

(T*9C/T*9V)*C16 FC/PC60C 21 1590 44.0 33.6 14.00 12.00

(T*9C/T*9V)*C20 FC/PC60C 21 1645 44.0 33.6 14.00 12.00

(T*9C/T*9V)*D20 FC/MC/PC60D 24 1615 44.5 33.6 14.00 12.00

(T*(8,L)C/T*8V)*C16 FC/MC62D 21 1635 45.0 34.2 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC62D 21 1615 45.0 34.2 14.50 12.00

(T*9C/T*9V)*C16 FC/MC62D 21 1590 45.0 34.0 14.00 12.00

(T*9C/T*9V)*C20 FC/MC62D 21 1655 44.5 33.8 14.00 12.00

(T*9C/T*9V)*D20 FC/MC62D 24 1630 45.0 34.0 14.00 12.00

(T*(8,L)C/T*8V)*C16 UC60C 21 1625 44.0 33.0 14.00 12.00

(T*(8,L)C/T*8V)*C20 UC60C 21 1605 44.5 33.2 14.50 12.00

(T*9C/T*9V)*C16 UC60C 21 1590 44.0 33.0 14.00 12.00

(T*9C/T*9V)*C20 UC60C 21 1645 44.0 33.0 13.75 11.50

(T*9C/T*9V)*D20 UC60D 24 1615 44.0 33.0 14.00 12.00

GHGD60S41S4

T*(8,L)X*C20 FC/MC62D 21 1665 55.0 39.5 14.00 12.00

T*9X*C20 FC/MC62D 21 1595 55.0 38.5 14.00 12.00

T*9X*D20 FC/MC62D 24 1645 55.0 39.0 14.00 12.00

T*(8,L)X*C20 FC64D 21 1665 56.0 40.5 14.50 12.00

T*9X*C20 FC64D 21 1595 56.0 39.5 14.50 12.00

T*9X*D20 FC64D 24 1645 56.0 40.0 14.50 12.00

(T*(8,L)C/T*8V)*C20 FC/MC62D 21 1615 54.5 38.5 14.00 12.00

(T*9C/T*9V)*C20 FC/MC62D 21 1655 54.5 38.5 13.50 11.50

(T*9C/T*9V)*D20 FC/MC62D 24 1630 54.5 38.5 13.75 11.50

(T*(8,L)C/T*8V)*C20 FC64D 21 1615 55.5 40.0 14.00 12.00

(T*9C/T*9V)*C20 FC64D 21 1655 55.5 40.0 14.00 11.50

(T*9C/T*9V)*D20 FC64D 24 1630 55.5 39.5 14.00 11.50

1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number.

2. Variable speed furnaces have B.O.D (Blower on Delay) standard.

COOLING CAPACITY - With High Efficiency Motor Furnaces (Continued)

UNIT

MODEL FURNACE

MODEL COIL

MODEL1WCOOLING

RATED

CFM Net MBH SEER EER

TOTAL SENS.

13 SEER HP WITH VARIABLE SPEED FURNACES2

This manual suits for next models

Table of contents

Other York Heat Pump manuals

York

York E4FH018 User manual

York

York LX series Quick start guide

York

York H1RA018S78 Quick start guide

York

York TIWM006B21S Installation and operation manual

York

York YZB018 THRU 060 Quick start guide

York

York Sunline 2000 User manual

York

York YLCA 50 User manual

York

York EVJC 12 User manual

York

York Predator XP Series User manual

York

York MH Quick start guide

York

York Geysir User manual

York

York AFFINITY BHX Series Quick start guide

York

York Sunline 2000 BQ 036 Quick start guide

York

York Champion Series Quick start guide

York

York 10 Seer User manual

York

York 14 SEER-YHE SERIES User manual

York

York YZB018 THRU 060 Quick start guide

York

York YCUL0020 Installation and operating instructions

York

York YLUA0248 Series Owner's manual

York

York HMH7 Series Quick start guide

York

York STELLAR PLUS E*FH018 Quick start guide

York

York YCL09 User manual

York

York B1HH018 User manual

York

York SUNLINE 2000 BP 072 Quick start guide

Popular Heat Pump manuals by other brands

MICROWELL

MICROWELL HP 1000 GREEN Installation and user manual

Sanyo

Sanyo SAP120FCH Service manual

Daikin

Daikin EHYHBH05AA Operation manual

Panasonic

Panasonic WH-SDF03E3E5 Design handbook

Bryant

Bryant 544B Specifications

Airxcel

Airxcel 45000 Series Installation, operation and maintenance instructions

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Service manual

Dimplex

Dimplex LI 16I-TUR Installation and operating instruction

Carrier

Carrier WSHP Open v3 Integration guide

TGM

TGM CTV14CN018A Technical manual

Carrier

Carrier 38MGQ Series installation instructions

Kokido

Kokido K2O K880BX/EU Owner's manual & installation guide

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Installation and service instructions

Carrier

Carrier 48EZN installation instructions

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Installation and service instructions for contractors

Ariston

Ariston NIMBUS user manual

Weishaupt

Weishaupt WWP L 7 Installation and operating instruction

GE Zoneline AZ85H09EAC datasheet