YOKOGAWA DL850E Operation instructions
1
Precision Making
ScopeCorder Introduction
Workbook
DL850E series
Peter Schutte
Product Marketing Europe
Version 1.2 –August 2016
2 Precision Making
Introduction
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
This is the ‘ScopeCorder Introduction Workbook’ for the DL850E series ScopeCorders. This workbook is created to
help ScopeCorder users understand the basic principles of working with their instrument.
In a series of exercises we will walk through the most commonly used functionality, but also address some unique
ScopeCorder features.
To get familiar with the ScopeCorder’s knobs & keys and their functions, please consider starting with AppendixA.
In case you have questions, remarks or suggestions related to this document or the ScopeCorder instrument, please
contact your local representative, myself or go to the Additional resources for support.
Enjoy the exercises!
Regards,
Peter Schutte
Product Marketing –ScopeCorder
Phone +31 (0)88 –464 1817
Email peter[email protected]okogawa.com
3 Precision Making
Table of contents
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Appendix
a. DL850E(V) knobs and keys
b. Using a USB keyboard and mouse
c. Sample rate & measurement time
Additional resources
1. Factory Reset
2. A simple acquisition
3. Sample rate calculation
4. Zoom to get more detail
5. Save a waveform
6. Load & view a waveform
7. Save a screen image
8. RMS measurement
9. Cursor measurement
10. Hard disk recording –setup & create
11. Hard disk recording –load & view
12. Save a settings file
13. Load a settings file
14. Action on trigger
15. Window based OR trigger
16. Dual Capture
17. Channel labeling
18. Scaling & Units
19. Phase measurement between 2 channels
4 Precision Making
1. Factory reset
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
A Factory RESET may be performed if the set-up status of the ScopeCorder is unknown.
It may be useful before performing these exercises, or before beginning a new test procedure.
Follow these steps:
1. Turn OFF the ScopeCorder
2. Hold the RESET button while turning ON the ScopeCorder
3. Continue to hold the RESET button
4. Wait for the confirmation message (you will hear a BEEP):
‘Turned on pressing the RESET key. Will initialize’
5. Release the RESET button
6. Press the ESC button
DONE! Factory reset has been completed.
Initialize vs. Factory Reset
A factory reset will initialize ALL
settings, including those of the
communication interfaces. To
maintain communication interface
settings, use SETUP » INITIALIZE.
« Table of contents
5 Precision Making
Setup
2. A simple acquisition
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Prerequisite: You may wish to perform a factory reset (Exercise 1) before this exercise to ensure your
ScopeCorder matches the setup of the ScopeCorder used in these exercises.
In this exercise you will make a simple waveform acquisition. Please connect CH1 to the PROBE
COMP pins on the front of the ScopeCorder using a suitable 10:1 or 1:1 probe / test lead. Leave all
other channel inputs disconnected. Press CH1 and adjust PROBE to either 10:1 / 1:1 as appropriate
for the input lead-set being used.
Follow these keystrokes:
Active Channels
If other channels are still enabled, please
turn them OFF by double-pressing each one
of the corresponding channel buttons, such
as CH 2, etc.
PROBE COMP connection
DONE!
Results are displayed
on the next page.
« Table of contents
Next slide »
6 Precision Making
Results
2. A simple acquisition
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Show the signal over a longer time period
Use the Tim/DIV knob to change the length
of your acquisition.
Longer memory, higher sample rate
Increase the record length (memory size) to
increase the sample rate. To do so, press:
ACQUIRE » Use the Jog Shuttle to adjust the
Record Length.
« Table of contents
7 Precision Making
3. Sample rate calculation
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Sample Rate= Main (Record Length)
Total Time
=10.000 points
200μs/DIV×10 DIV
=10.000
2000μs=10.000
0,002s
=5MS/s
What sample rate & measurement time
settings are possible?
Dependent on channel count, available
memory and other parameters different
sample rates & measurement times are
available. Review Appendix C for more
information.
« Table of contents
8 Precision Making
Setup
4. Zoom to get more detail
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Prerequisite: Perform Exercise 2 first, or acquire a waveform.
In this exercise you will use the Zoom functionality to get more detailed insight in the acquired signal, while still having
the ability to make long acquisitions.
Follow these keystrokes:
10ms/div 200μs/div
DONE!
Results are displayed
on the next page.
« Table of contents
Next slide »
9 Precision Making
Results
4. Zoom to get more detail
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Use the 2nd Zoom channel
In the given example, the second Zoom
channel has been activated to get even more
detail by zooming in on Zoom channel 1. To
do this press:
Zoom1/Zoom2 » Display (set to: On) » Zoom2
Source (set to: Zoom1)
Now use the Magnitude and Position knobs
to fine tune the Zoom windows.
« Table of contents
10 Precision Making
Setup
5. Save a waveform
ScopeCorder introduction workbook
Copyright © Yokogawa Electric Corporation
Prerequisite: Perform Exercise 2 first, or acquire a waveform.
In this exercise you will save a waveform to a binary file.
Follow these keystrokes:
Enter a file name with the navigation keys
DONE!
One button operation
After you have performed the
above setup, you simply press one
button SAVE. You can skip all but
the last step, if you wish for the
DL850E(V) to name file(s) for you.
File Directory
To see a directory listing with your
file, press: FILE » UTILITY and use
the SET button and SHUTTLE-knob
to set PATH=HDD, in this example.
« Table of contents
Other manuals for DL850E
3
Table of contents
Other YOKOGAWA Test Equipment manuals
YOKOGAWA
YOKOGAWA 3226 User manual
YOKOGAWA
YOKOGAWA AQ1200A User manual
YOKOGAWA
YOKOGAWA DLM2000 Series User manual
YOKOGAWA
YOKOGAWA DL7440 User manual
YOKOGAWA
YOKOGAWA CA320 User manual
YOKOGAWA
YOKOGAWA CA310 User manual
YOKOGAWA
YOKOGAWA DL 1540 User manual
YOKOGAWA
YOKOGAWA AQ1100A User manual
YOKOGAWA
YOKOGAWA 90020B User manual
YOKOGAWA
YOKOGAWA EY200 User manual
YOKOGAWA
YOKOGAWA 279301 User manual
YOKOGAWA
YOKOGAWA DLM2000 Series User manual
YOKOGAWA
YOKOGAWA DLM3022 User manual
YOKOGAWA
YOKOGAWA DLM4000 Series User manual
YOKOGAWA
YOKOGAWA CA700 User manual
YOKOGAWA
YOKOGAWA AQ1215A User manual
YOKOGAWA
YOKOGAWA ScopeCorder DL350 User manual
YOKOGAWA
YOKOGAWA CA550 User manual
YOKOGAWA
YOKOGAWA 30031A User manual
YOKOGAWA
YOKOGAWA 30032A User manual
