Xtreme X-400 User manual

Page

(photos may vary)

X-Treme TM Electric Scooters

Model: X-400

Product Handbook

Page

PLEASE BE SAFE WHEN RIDING

ALWAYS WEAR AHELMET AND OBEY ALL LAWS!

BATTERY MAINTENANCE and

CHARGING INSTRUCTIONS

1. You MUST charge completely prior to initial use. (Follow

charging instructions in your Product Handbook)

2. Charge immediately after each use.

3. Charge before storage. You must charge every 30 days if not

in use.

4. Charge the unit for 6-8 hours after the light on the charger turns

green.

5. DO NOT allow this unit to deep discharge the battery.

6. For safety purposes, DO NOT charge for over 24 hours.

7. Turn the unit OFF when not in use.

This PRODUCT IS NOT INTENDED FOR EXTREME or

OFF-ROAD Use! Please take care of your X-400!

DO NOT JUMP or ABUSE THIS PRODUCT!

DO NOT RIDE IN WET/ICY CONDITIONS!

Failure to follow these instructions will

VOID YOUR WARRANTY!

IMPORTANT

Failure to follow these INSTRUCTIONS will

VOID YOUR WARRANTY!

Page

WARNING

This product does not conform to Federal Motor Vehicle Standards and is not

intended for operation on public streets, roads or highways. Serious injury can

result from the unsafe operations of this product. Operator can minimize these

risks by using certain safety equipment such as: safety helmet, goggles, gloves,

elbow and kneepads and appropriate footwear.

DO NOT operate this product in traffic, on wet, frozen, oily or unpaved surfaces or

under the influence of drugs and/or alcohol. Avoid uneven surfaces, potholes,

surface cracks and obstacles.

DO NOT use a water hose to clean this product. See Product Handbook for more

information.

This product is recommended for riders 12 YEARS OF AGE and older.

SAFETY

Persons without excellent vision, balance, coordination, reflex, muscle and

bone strength and good decision-making capabilities should not use this

product.

Minors without adult supervision should not use this product.

Persons unwilling or unable to take responsibility for their own actions should

not use this product.

The user of this product assumes ALL risks associated with its use. To

minimize these RISKS, the user must wear safety helmet, goggles, gloves,

elbow and kneepads and appropriate footwear.

This product is ELECTRIC! DO NOT ride this product in wet conditions,

puddles or rainy weather.

IMPORTANT

PLEASE READ THIS BEFORE USING THIS PRODUCT

READ THIS FIRST!

Page

SAFETY GUIDE

The recommended age for riding this scooter is 16 years old.

To avoid damage to the motor and footplate, do not overload the scooter.

Never ride with more than one person.

Inspect your scooter thoroughly before each use for loose or missing parts.

Avoid unintentional starts by turning the scooter off while not in use.

To avoid the risk of a short circuit in the electrical parts, do not use your

X-Treme Electric scooter in the rain and never spray or wash off your scooter

with water.

Do not place the battery near fire or heat.

To avoid damage to the battery, do not use the charger if it has been damaged

in any way.

Keep hands, face, feet and hair away from all moving parts.

Do not touch the motor or wheels while they are rotating.

Brakes are designed to control speed as well as stop the scooter. Practice

braking for proper slowing down and smooth stops.

Maintain your X-Treme X-400 as recommended in this Product Handbook.

Use only quality replacement parts as recommended by the manufacturer.

Inspect the entire scooter prior to each use. Replace any part that is cracked,

chipped or damaged before use.

*NEVER ALLOW CHILDREN TO OPERATE THE SCOOTER WITHOUT ADULT

SUPERVISION.

*NEVER ATTEMPT TO OPERATE THE SCOOTER WHILE UNDER THE

INFLUENCE OF ALCOHOL.

If a situation arises that is not covered in the manual,

proceed with caution and use good judgment.

Contact your dealer or X-Treme (www.x-tremescooters.com/support/)

if you need further assistance

QUICK

REFERENCE

SAFETY GUIDE

Page

TABLE OF CONTENTS

IMPORTANT NFORMATION…………………………………….………………2-3

QUICK REFERENCE……………………………………………………………….4

TABLE OF CONTENTS……………………………….…………….………………5

GETTING TO KNOW YOUR X-TREME X-400…………………………………..6

PACKAGE CONTENTS…………………………………………………………….7

GETTING STARTED/ASSEMBLY....……………………………..………………..7

CHARGING…………….…………………………………………………………….8

RIDING…………………….……….………………………..……………………….9

STOPPING AND BRAKING. …………………………………….…………………9

FOLDING & STORAGE………………………………………………………..……9

BRAKING SYSTEM…………..…………………………………….…………….…9

ADJUSTING THE BRAKES……….…………….………………………..……9-10

TIRES……………………………………………………….………………………11

BATTERIES…………………..……………………………………...……………..11

MAINTENANCE…….….…………………………………………………………..11

ADJUSTING THE CHAIN………………………...……………………………….11

MAINTENANCE SCHEDULE…………………………………………………….12

OTHER QUESTIONS…………………………………………………………...…12

GENERAL INFORMATION/TECH SUPPORT………………………………….13

Page

GETTING TO KNOW YOUR X-TREME X-400

(Photo’s may vary)

Page

PACKAGE CONTENTS

Your X-Treme X-400 comes with the following items in the box. Please locate

all of the following:

1. The X-Treme X-400 Scooter

2. 36V Battery Charger

3. Tool Kit

4. Product Handbook

5. Seat & Seat Post

GETTING STARTED

Please read and understand these instructions and the OPERATING

PROCEDURES section, prior to starting or riding your X-400

Fig, 1

Fig. 2

Fig. 3

Assembly

1. Carefully remove the X-400 from the box.

2. To unfold the X-400, begin by lifting up on

the FOLDING HANDLE CLAMO with one

hand (Fig.1), while gently pulling up on the

handlebars with the other (Fig.1)

3. Secure the handlebars in the upright

position by tightening the handlebar-folding

clamp. Fig. 2

4. Assemble the T-Handlebar by inserting it

into the handlebar post. Fig. 3

5. Secure the T-handlebar to the post by

tightening the clamp at the desired position.

This setting is adjustable if required. Fig.

6. Insert the assembled T-Handlebar into the

Front Fork as shown in figure 4.

7. Tighten the bottom handlebar clamp using

the appropriate tools as shown in figure 5.

8. Insert the seat into the silver seat post and

tighten the nuts securely.

9. Insert the assembled seat and seat post

into the seat post as shown in figure 6.

10. Finally insert the seat post into the seat

post receiver in the frame and tighten the

clamp. Fig. 7

Page

Fig. 4 Fig. 5

Fig. 6 Fig. 7

Charging

Your scooter comes charged out of the carton. We still recommend charging the unit for

8-10 hours prior to it’s first use. We also recommend charging your scooter after each

use and prior to storage.

WARNING: Do not allow your scooter to go into deep discharge, as this will damage the

batteries.

Fig. 8

Fig. 9

1. Make sure unit is turned off.

2. Open the charging socket cover

located on the right side of the

scooter frame, under the

footplate. (Fig. 8)

3. Locate your Battery Charger.

(Fig. 9) Find the charger socket

end plug it into the scooter.

4. Next, plug the AC plug into a wall

outlet.

When first plugged in, the charger has

two red lights that will illuminate at the

same time, indicating that the charging

process has started. Once the light on

the charger turns green, you may remove

the charger and close the safety cap.

Page

Fig. 10

**Your scooter has a variable speed hand throttle. You can control the speed of your

scooter by the amount of pressure you use when rotating the hand throttle. The more

you rotate, the faster you will go.

Kill Switch

The kill switch is located on the right handlebar next to the throttle. This switch when

depressed kills all power to the motor.

STOPPING & BRAKING

To brake, release the THROTTLE GRIP and depress the BRAKE LEVERS (on the

left/right side of the handlebars. Depressing the brake will disengage power to the motor.

When the unit feels like it is loosing power or not accelerating to full speed, the scooter is

ready to be re-charged.

FOLDING & STORAGE

When you are done riding the X-400 you can fold it for compact storage and transportation.

To fold down the X-400, loosen the handlebar-folding clamp. Raise the clamp while

pulling the handlebar down with your other hand. BE CAREFUL NOT TO HIT YOUR

HEAD WITH THE HANDLEBAR. Push down until you feel the mechanism lock into the

down position.

BRAKING SYSTEM

The X-400 uses a pinch braking system for the front, and a hub system for the rear. They

are both activated by a hand brake lever on the left and right side of the handlebar.

Squeezing the hand brake lever with your left hand activates the rear brake. Squeezing

the hand brake lever with your right hand activates the front brake. Make sure to release

the HAND THROTTLE GRIP when engaging the brakes. Practice braking on a smooth,

dry surface to get used to the feel of the braking system. Braking distance is affected by

wet conditions and loose and uneven riding surfaces.

ADJUSTING THE BRAKES

The Brakes on the X-400 should come fully adjusted from the factory.

However, it may be necessary to adjust the brakes from time to time.

RIDING

1. Make sure that all of the exposed bolts and screws

are tightened.

2. Raise the kickstand to its upright position.

3. Turn the scooter on using the key switch located on

the left side of the scooter under the footplate. Fig.

4. Gently rotate the THROTTLE GRIP, on the right

side of the handlebars. The X-400 will begin to

move on its own power.

Page

Fig. 11

Fig. 12

Fig. 13

Fig. 14

Fig. 15

To adjust the Rear Brakes:

For brakes that are adjusted too tight:

1. Loosen the tension screw on the

left right hand brake lever by

rotating it counter-clockwise until

the wheel spins freely. (Fig. 11)

For brakes that are adjusted too loose:

2. Tighten the tension screw on the

left hand brake lever by rotating it

clockwise until the wheel has a

slight drag. (Fig. 11)

For further adjustment, locate the

adjustment screw on the rear brake hub

and follow the instructions below.

For brakes that are adjusted too tight:

3. Loosen the tension screw on the

brake hub by rotating it clockwise

until the wheel spins freely. (Fig. 12)

For brakes that are adjusted too loose:

4. Tighten the tension screw on the

brake hub by rotating it

counter-clockwise until the wheel

has a slight drag. (Fig. 12)

For further adjustment:

5. Locate the adjustment screw on the

front brake assembly (located

above the front wheel, Fig. 123)

Tighten or loosen as necessary.

To adjust the Front Brakes:

**For brakes that are adjusted too tight

or too loose, follow steps 1-2 above.

For further adjustment, follow the steps

below.

To adjust the brakes to the desired

tension:

1. Loosen the pinch nut by turning

counterclockwise. Fig. 12

2. Using your free hand, pinch the

brake arms and pull or loosen the

crossover brake cable to the

desired tension. Fig. 13

3. When the desired tension has been

obtained, tighten the pinch nut by

turning clockwise. Fig. 14

Table of contents

Popular Scooter manuals by other brands

TEKTRO

TEKTRO CHEETAH owner's manual

Douglas

Douglas Vespa Sprint Operation and maintenance

PLAYTIVE

PLAYTIVE AS-2448 Instructions for use

Ebinger

Ebinger DONKEY XL User instructions

Flyer

Flyer Mountain Original instruction manual

BackCountry eBikes

BackCountry eBikes Storm owner's manual

equipmed

equipmed FreeRoam II user manual

Yoto

Yoto Lion owner's manual

WESTHILL BIKES

WESTHILL BIKES LINK user manual

BAnff

BAnff eProdigy series Assembly manual

Winther

Winther 475 Assembly instruction

Jetson

Jetson JBZL17 user manual

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 user manual

Carrera

Carrera impel manual

Afikim

Afikim Superlight SL-3 user manual

CareCo

CareCo ZOOM owner's manual

Douglas

Douglas Vespa G.S. Service manual

Gazelle

Gazelle with BOSCH System user manual