XINDAO Multi sport E-ink User manual
Multi Sport
E-ink watch
Copyright © XD P330.92x
2
3
Content
English p. 4
Français p. 14
Italiano p. 24
Deutsch p. 34
Polski p. 44
Español p. 54
Svenska p. 64
Nederlands p. 74
4
ENGLISH
Compatible with below versions:
Apple Store:
Google Play store:
Support Bluetooth 4.0
iOS 8.0 & above
Android 4.4 and above
Congratulations with your Multi sport E-ink watch! All activities are displayed on the APP after synching with the
data from the wristband. Please read this manual carefully and check the FAQ if needed.
Please note: the screenshots below diers from versions of the APP due updates of the new versions.
1. Specification:
Notice: IP67 standard means under normal temperature, product could be in 1m deep water last for 30 minutes.
Please pay attention to following two points:
1. IP67 means that it can pass the test of soak 30 min in 1m deep water, but doesn’t mean to swim without being
aected
2. IP67 means that it can keep working under 1 m deep water within 30 min, but doesn’t mean vapor proof, so you
may find the steam in screen after shower, because waterproof standard is based on cold water.
2. Device activate & charger:
1. Charge the watch for 1 hour before using it.
2. Make sure that the watch is full charge in order to work properly. Once the device with low battery status, please
charge the device with the charger. Clamp the charging clip to the 3 point positioned on the back of the watch.
1.28 inch 128*128 pixel E-ink display
Display:
Waterproof:
Charging:
Function: Dynamic heart rate measurement, sleep monitor, activities reminder, pedometer,
distance, calorie, remote camera control, call remind, SMS notifications from social
media.
IP67 waterproof
3 point connect charge DC 5V/0.5A
5
iOS 8.0 & above
Android 4.4 and above
3. Device Charging
Please place the Magnetic Charging Cable on the back of the watch (as shown in the figure ).Plug it into the power
adapter, or 5V/500mA(or above) standard USB adapter. For example: Laptop, USB adapter, Bank Power and others.
When wristband screen appears icon,which means is being charged.
Place the Magnetic
Charging Cable on the
reverse side.
4. Download Application
Before connecting with the app Linksmart, please make sure the Bluetooth connection of your mobile device has
been enabled. To use “LinkSmart” APP, make sure your mobile device is connected to the internet via Wi-Fi / 4G/ 3G.
5. Wear the device
1. Press and hold the screen until the display will switch on (If there is still no response, please try again after
charging)
2. Put the watch on the wrist with the screen facing up. Make sure it fits well for accurate results.
1. Apple iPhone (IOS 8.0 and up), please search “LinkSmart” in the App store to
download/ install it.
2. Android phone (4.4 and up), please search “LinkSmart” in Google Play to
download and install it.
Download the app by either scanning the QR code below or search for “LinkSmart”
and download in the Apple Store or Google Playstore.
6
6. Pair the device
• On your mobile device make sure the Bluetooth is enabled.
• Power on the watch
• Open the APP Linksmart, Click the [Device] In the bottom of main interface.
• In the bottom of [Device], click the “Add device”.
For example: The watch ID code is 3892 in the Bracel03-3892.
Notice:
If connection problems occur and the APP keeps showing pairing but cannot pair successfully. Please power o the
watch first. Then power on the watch,long press the code,the watch will vibrate three times. Connect the APP again.
7. Function icons:
CyclingBadminton Basketball Body mechanics Climbing
7
Pull-upDance Fitness Football Plank
CameraTraining Schedule Music Power o
SkatingPush-up Sit-up Shuttlecock Running
VolleyballSkipping Yoga Table Tennis Tennis
Heart rateBowling Mountaineering Skiing Sedentary reminder
FunctionSteps Distance Calories Message
8
Left & right Press and hold to start Long press
Press and hold to endUp & down
Alarm clock Remote camera
5. Function schematic diagram:
1. Operation mode: touch or slide screen , hold and long press to confirm.
2. Operate the watch
9
6. Synchronize data
The Watch synchronizes data automatically after pairing/connecting with your
smartphone. Syncing data includes steps, calorie, distance, date and time. To synchronize,
please click the above left corner to synchronize; it will take 1-2 minutes. When unable to
synchronize data, disconnected the Bluetooth and retry to connect again.
8. Calling and message reminder
Go to [Device] tab, click [Device setting] to choose
[message push] . For Android smartphones, it will show
you below, allow ‘LinkSmart’ to send you notifications
7. Sleeping monitor
The watch/device could detect and recognize automatically your sleeping status and
monitors the whole sleeping progress. This device will analyze/tracks your sleeping
quality based on the movements you make during night.
Bad quality sleep > lots of movement
Good quality sleep > little movements
Note: you will need to wear the watch during the nighttime
in order to get the results of your sleeping quality during
the night.
Enable the sleep monitoring in the app by going to the
“Device” tab and then enable the sleep monitor, the watch
will detect automatically if you are under sleeping mode.
Icon Function Operation
Dial pictures optional Long press and slide to choose dial pictures
Long press to shift on/o
Long press
Test heart rate automatic
Find your phone
10
10. (Remote) Camera Control
By going to the “Device” tab, you can click on
“Camera”. You will see a circle icon on the screen of
the app. By touching/press on the icon , you can
control the remote of making photos.
11. Sports type
Go to the [Activity] tab, click on the “+” to add sport
type. Or go to [Device] interface, click on the [Target
setting]. You can choose any five type of sports. You
can set an exercise goal and reminder.
9. Alarm and activity/sedentary reminder
Set alarm by going to “Device” tab in order to add alarm. The watch will vibrate to remind you. To remind you to be
active after (adjusted) period without any movements, please enable “sedentary reminder” in the “Device” tab in
order to adjust the setting according to your preference.
For IOS smartphones, you need to allow “LinkSmart” to
send your notifications, once you download the app or go
to phone Setting to allow the notifications.
For IOS smartphones, you need to allow “LinkSmart” to
send your notifications, once you download the app or go
to phone Setting to allow the notifications.
Call/message reminder
Incoming call/messages (WhatsApp, SMS, etc.) will show
on the watch screen and will vibrate. Once enabled the
function, the name of the caller will show on the screen.
For messages, you will see the name of the sender and the
content of the messages
Table of contents
Languages:
