Xiaomi Mijia DC User manual
Operation Instructions for Mijia DC Frequency Conversion Tower Fan
Safety Instructions Please read this manual carefully and keep it properly
before.
Attention
Installation
Please be sure to install this product correctly according to the instructions, otherwise electric
shock, fire, personal injury and other damages will occur.
The tower fan has not been assembled, please do not connect the power supply.
Handling
When moving, be sure to stop the tower fan and unplug the power plug.
When moving, please hold the tower fan firmly to avoid machine damage or personal safety
caused by falling.
Using
If the product has abnormal noise, peculiar smell, high temperature, tilt, body shaking and other
abnormalities, please stop using it immediately.
Do not lean against or tilt the tower fan during operation.
Do not swing the tower fan body manually to avoid damage to the internal transmission
mechanism.
Power cord
Please unplug the power cord from the power outlet before performing maintenance work or
moving the tower fan.
When pulling out the power cord, pull it up from the power plug. Do not pull the power cord.
If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from
the manufacturer, its maintenance department or similar departments.
Warning
If it is not used properly, electric shock, fire personal injury and other damages may occur.
Do not use this product in nearby places where there are easily inclined or unstable objects.
Please do not use this product in high temperature and humid environment such as bathroom.
Do not use this product when the power cord is damaged or the power plug is loose.
Do not run this product when the rear grille is not installed or when the rear grille is loose or
falls off.
Do not allow children or adults who do not understand this instruction to operate this product.
Please do not disassemble and repair this product without permission.
Do not excessively pinch, bend or twist the power cord to prevent the core from being
exposed or broken.
Do not insert fingers or foreign matter into the tower fan grille or the running impeller.
Do not put hair, fabric, etc. close to the tower fan to avoid danger caused by being involved.
Do not use inappropriate power outlets.
Before removing the rear grille, it must be ensured that the tower fan is disconnected.
包装清单
Packing List
①Tower fan main body ②front chassis ③rear chassis ④M5 screw × 2 ⑤special wrench ⑥
operation manual
Hint: The illustrations of products, accessories and user interfaces in the manual are all schematic
diagrams for reference only. Due to the update and upgrade of the product, there may be slight
differences between the physical product and the schematic diagram, please refer to the physical
product.
Product Introduction
Top view of tower fan Timing adjustment key
Air Volume/Timing Indicator
Wi-Fi Indicator
Shake the head key
Sleep Wind Mode Indicator
Mode Switch Key
Natural Wind Mode Indicator
Direct Blowing Mode Indicator
Power
Air volume adjusting key
chassis, front grille, tower fan main body Rear grille, power cord outlet, chassis bottom
Installation
Step 1: Splice the chassis
定位柱 定位孔 底盘
Positioning column, positioning hole, chassis
1.
As shown in the figure, insert the positioning column of the rear chassis ③into the positioning
hole of the front chassis ②and press it to buckle it in place to splice the rear chassis and the front
chassis into a flat chassis.
2.
Pass the power cord at the bottom of the tower fan main body ①through the round hole in the
center of the chassis.
Step 3: Arrange the power cord
Install the power cord into the trunking at the bottom of the chassis, lead it out from the outlet of
the power cord, and complete the installation of the tower fan.
Hint: normally straighten out the power cord and load it into the trunking, which will not damage
the power cord.
Use
Connect the power supply
Insert the power plug into the qualified power socket, and after hearing the "beep" tone, the tower
fan is successfully connected to the power supply.
Switch on and off
Switch on
Press key and the tower fan starts to work. For the first time, the default is direct blowing
mode, with 1 windshield.
Switch off
Press the key in the startup state to stop the tower fan from working.
Switching air volume
Press the key to switch the air volume gear, and the corresponding air volume indicator light
will be on for a long time (as shown in the following table). The next time you start up, the
default is the air volume gear used when you last shut down.
挡位
Gear
1挡
1st gear
2挡
2nd gear
3挡
3rd gear
4挡
4th gear
显示状态
Display Status *●●● **●● ***● ****
Tip: * Lighted State ● Off State
Switch Mode
Press the key to switch the modes of direct blowing, natural wind and sleep wind, and the
corresponding mode indicator lights will be on for a long time. The next time you start up, the
default is the mode used when you last shut down.
Set Shake Head
Press the key to turn it on or off and shake your head. Users can set the shaking angle in
APP.
The next time you start up, the default is the shaking head setting used when you last shut down.
Hint: After resetting Wi-Fi, the tower fan shaking angle will return to the default angle of 90.
Timing shutdown
Press the key to switch the timing gear cyclically: 1 hour, 2 hours, 3 hours and 4 hours, turn
off the timing, and the corresponding timing indicator light will be on for 5 seconds (the
following table). After the timing indicator light is on for 5 seconds, it will return to the air
volume indicator mode.
定时
Timing
关闭定时
Close Timing
1小时
1 hour
2小时
2 hours
3小时
3 hours
4小时
4 hours
显示状态
Display
Status
●●●● *●●● **●● ***● ****
Tip: * Lighted State ● Off State
Connect Mijia APP
This product has been connected to Mijia and can be controlled by Mijia APP or Classmate
XiaoAi, and is interconnected with other products.
Scan the QR Code, download and install the Mijia APP. Users who have installed the Mijia APP
can directly enter the device connection page. Or search for "Mijia" in the application store,
download and install Mijia APP. Open the home page of Mijia APP, click "+" in the upper right
corner of the page, and add devices according to the APP prompt.
Hint: Due to the upgrade and update of Mijia APP, the actual operation may be slightly different
from the above description. Please follow the current guidelines in Mijia APP.
works with mijia
Accessed to Works with Mijia
Connect to Wi-Fi
At the same time, press the key and the mode switch key for a long time. After hearing
the long sound "beep", enter the waiting connection state and connect the device according to the
APP prompt.
Wi-Fi Indicator Display Status:
Wi-Fi 状态
Wi-Fi Status
等待连接
Waiting for
Connection
连接中
Connecting
已连接
Connected
连接失败
Connection
failed
指示灯状态
Indicator status
橙色闪烁
Orange flicker
蓝色闪烁
Blue flicker
蓝色长亮
Blue long bright
橙色长亮
Orange long
bright
Maintenance
Washable parts: rear grille, and impeller
Rear grille, impeller
Table of contents
Other Xiaomi Fan manuals
Popular Fan manuals by other brands
ELTA FANS
ELTA FANS H03VV-F installation guide
Hunter
Hunter 20714 Owner's guide and installation manual
Emerson
Emerson CARRERA VERANDA CF542ORB00 owner's manual
Hunter
Hunter Caraway Owner's guide and installation manual
Panasonic
Panasonic FV-15NLFS1 Service manual
Kompernass
Kompernass KH 1150 operating instructions
