WolfVision EYE Series User manual
1
Ceiling Tile
EYE Series Mounting Kit
Part 1: Tile Bridge Installation
The Ceiling Tile Bridge is designed to support the WolfVision EYE Series models only. T-Grid ceilings are not
designed to support weight loads –support wires must be attached to the structural ceiling above. It is the
responsibility of the installer to ensure this product is properly supported and meets all local building codes
and plenum requirements. Make sure the ceiling structure is capable of holding at least 12 lbs. (4x the
combined weight of the mount and camera).
Steps:
I Inspect Installation Location
1) Determine mounting location within T-
grid ceiling based upon the center of the
desired focal point on the working
surface.
Note: An adjacent tile will also have to
removable for access.
2) Verify structural support (T-grid wire
above the ceiling tile). Check overhead
clearance. A minimum of 8 1/2’’ above
Ceiling tile is required. After you have
verified all clearances, replace the ceiling
tile.
Note: Center of installation must be at least
3 11/16’’ from both ceiling grid structures
to allow for hole clearance.
8 ½ ’’
3 11/16 ‘’
3 11/16 ‘’
2
Ceiling Tile
Ceiling Tile
A
C
B
G
F
E
D
II Assemble Unit
3)
ACamera Bracket
BTrim Mounting Screw
CMounting Tab
DMounting Screw
EMounting Screw
FRail Clamp Screw
GAlignment Ring Nut
H (Optional) Light Mask
4) Using Mounting Screw (E), attach Camera
Bracket (A) to circular plate.
Note: For installations using optional lenses,
longer brackets are available for purchase.
5) Slide circular plate into mounting
assembly.
6) Secure circular plate into mounting
assembly using Mounting Tabs (C) and
Mounting Screws (D).
Note: Use the center hole of the Mounting Tab
(C). (Countersunk screw hole is not
needed in this step). Only 2 Tabs are
required. You must use the screw holes
closest to rail clamps (see photo).
H
Rail clamp
Rail Clamp
3
Ceiling Tile
7) Slide assembly into the frame.
Note: After assembly is in place, insert the two
Rail Clamp Screws (F).
8) Loosen frame screws.
9) Install camera into the assembly –tighten
¼ - 20 knurled screws (supplied with
camera).
Note: It is recommended that the lens cap be
left on for the entire installation process.
4
Ceiling Tile
Ceiling Tile
III Mounting Instructions
10) Using the center focal point on the table,
run a plum-line to the ceiling tile and mark
the center point where the camera will
mount.
11) At this point you are ready to cut the hole.
Be sure you have checked the clearances
side to side and above the tile.
(As stipulated in step 2)
12) Cut a 7 3/8’’ diameter hole. The alignment
ring may be used as a template.
5
Ceiling Tile
13) Install assembly above ceiling tile.
Verify the hole alignment.
14) Secure assembly by tightening the Frame
Screws onto the grid and tightening the
Rail Clamp Screws (F).
Note: If you need to change the orientation
of the image to match the architectural
specifications of the room, loosen the
Mounting Tabs (
C) and rotate the camera
assembly as needed. Secure Tabs.
6
Ceiling Tile
Ceiling Tile
15) Using this anchor point, attach safety cable
to building structure.
(Safety cable not included)
16) Loosen knurled screws and lower camera
until flush with bottom of ceiling tile. A
straight edge may be used to verify.
17) Attach alignment ring to face-plate with
Nuts (G) provided.
7
Ceiling Tile
18) (Optional)
Place the four Trim Mounting Screws (B)
though the trim ring. Peel back the
adhesive backing from the Light Mask (H
).
Use the four screws (B) to align the mask
properly and adhere to rear of trim ring.
Note: The Light mask (H) is optional. It may be
used to block light and/or airflow from
the camera opening.
19) Install face-plate ring using Trim Mounting
Screws (
B).
Final Product
8
Ceiling Tile
Ceiling Tile
EYE Series Mounting Kit
Part 2: Sheetrock Installation Guide
This lightweight mounting bracket is designed to support the WolfVision EYE Series models above sheetrock
ceilings. A safety cable anchor point is provided to secure the unit to the building structure. It is the
responsibility of the installer to ensure this product is properly supported and meets all local building codes
and plenum requirements. Make sure the ceiling structure is capable of holding at least 12 lbs. (4x the
combined weight of the mount and camera).
Steps:
I Inspect Installation Location
1) Determine mounting location ceiling based
upon the center of the desired focal point
on the working surface.
A minimum of 8 1/2’’ clearance above
ceiling is required.
Center of installation must be at least 3
11/16’’ from structural members in ceiling
to allow for hole clearance.
II Assemble Unit
2)
ACamera Bracket
BTrim Mounting Screw
CMounting Tab
DMounting Screw
EMounting Screw
(Not used in sheetrock installation)
FRail Clamp Screw
GAlignment Ring Nut
H (Optional) Light Mask
3) Using Mounting Screw (E), attach Camera
Bracket (A) to circular plate.
Note: For installations using optional lenses,
longer brackets are available for purchase.
A
C
B
G
F
E
D
1
Sheetrock
H
9
Ceiling Tile
4) Slide circular plate into mounting
assembly.
5) Secure circular plate into mounting
assembly using Mounting Tabs (C) and
Mounting Screws (D).
Note: Use the center hole of the Mounting Tab
(C
). (Countersunk screw hole is not needed
in this step). Only 2 Tabs are required. You
must use the screw holes closest to rail
clamps (see photo).
6) Attach the four Mounting Tabs (C) with
Mounting Screws (E). Do not tighten
screws.
2
Sheetrock
Rail clamp
Other manuals for EYE Series
1
Table of contents
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
